gmrhodes13

Great work on the EIB updates, a few suggestions before the DO's get here: You appear to have a small amount of paint on the gums Top corners of your kidney are sticking out, perhaps some plastic tabs behind my keep them in alignment with the ab. Also you have different gaps at the top of your thighs between them and your cod. Also different gaps at your wrists, perhaps it is the handplates positioning Your thighs are touching in a few areas, you may want to address these Vocoder paint is a little wobbly on one side A few other photos will no doubt be needed Close up of the sniper plate, front and both sides Close up of the thigh ammo strip connectors/rivets, inside and outside Close up of your side ab/kidney rivets Ear bottom screws Full side photos arms up Close up of the detonator scews/clips Helmet S trim Helmet lens color Full right side of blaster Blaster D ring Good luck with approval

They are pretty darn close, I would suggest leaving them for now and see if the DO's address them in your applications

Nice work, almost there

Apparently the guy also appeared in Indiana Jones

Hello and welcome aboard, sounds like you have research well in hand, good luck and hope to see a build thread from you soon.

Cheers guys

Great advice, using a test piece of plastic to prefect the countersink From memory I think my right ear was the worse to fit, trying to get the "ideal" angle of the ears, ended up slotting the holes on the backplate to move around a little. Paint work is looking great

Glad I could be of help (and that's the only seeds I'm planting ) Just one thing, I would glue them on the front: These shall be affixed in the front

Some references

And Hex3D on FB is working on some 3D files for those action figure collectors, based on Matt the radar technician

Great idea came out well, nice work

I've not heard of these before, looks like it may need some tweaking for higher level approval, the counter is very low but not a bad looking blaster Comparison

Nice work trooper, a great build overall, a couple of suggestions before the DO's get here: Your shoulder straps on the back are not quite centered to the backplate, also there is white excess elastic showing Noticed your cocking lever is silver, these are normally black star- Could you also post thigh ammo strip inside connectors, I know the DO's like to see that Good luck with approval although I doubt you will need it.

I can just see people dressed up holder a corridor wall walking around celebration

https://www.whitearmor.net/forum/topic/8240-the-right-hand-side-snap-and-chest-and-back-question/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/8760-ap-armor-questions-assembly-glue/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/8758-something-a-little-different-with-a-twist/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/8694-show-me-your-shims/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/8801-attaching-shoulder-covers/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/8424-sds-hdpe-faceplate/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/8647-how-i-closed-the-side-gaps-on-my-tx/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/8621-what-i-have-accomplished-in-2-days/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/7466-non-matching-abs-conundrum/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/8527-my-rt-mod-sandtrooper-helmet-pre-weathering/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/7526-my-ata-helmet-in-progress/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/5486-shimmery-green-looking-lenses/, restored by gmrhodes13 80

We've been joking about this in command, must be real, he has his own figure, and a Lego figure

Helps to leave a little excess on the front bottoms of the backplate, from memory the right side doesn't quite cover as well as the left. As I wanted a specific brow height I ended up with a small gap between these pieces but it was covered by the ears

Congratulations once again trooper, it was worth the extra work

Nice work, you could take a smidgeon more just on a couple of the lower sections, appears on this view that there is still some paint excess

Could be the actual helmet but a couple of the teeth cut outs look a little curved when you do a comparison

Great work on the fixes

Congratulations trooper and welcome to the Centurion ranks

Looking forward to see the progress

You can always re-dril another hole, remember the ear will cover this area

https://www.whitearmor.net/forum/topic/9171-how-to-get-metal-blaster-past-customs/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/9465-mrce-tube-stripe-placement/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/9460-501st-bucket-or-just-a-display/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/9320-found-a-nice-chin-strap-and-padding-for-your-buckets/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/9191-hand-plates-and-thighs-hassles/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/9166-femtrooper-minifig-mod/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/8880-tie-paint-jobdecal-questions/, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/9149-ata-helmet-trimming-questions/, restored by gmrhodes13 78