Sly11

100% agree with Steve, the journey is awesome. Sent from my iPad using Tapatalk

I think you are on the right track, I am approx 5'9" 148 pounds and I went with AP, you will not be disappointed . Sent from my iPad using Tapatalk

Had the same drama with the humidity and fogging even with two fans running. Sent from my iPad using Tapatalk

Industrial Velcro Sent from my iPad using Tapatalk

Nice neat job, shouldn't take too much to clean up, and it looks better already. Sent from my iPad using Tapatalk

Looking awesome. Sent from my iPad using Tapatalk

Or of course you can just go and buy some Plasti Polish that does the same or similar thing although not as much fun as mixing up your own poisonous concoctions. Sent from my iPad using Tapatalk

Lol[emoji23], and of course, I would not expect any less of an observation from you Steve. Sent from my iPad using Tapatalk

Sorry one more thing, how easy is it to get your hands through the wrist of your fore arms? , it should be a tight fit pushing them through. Sent from my iPad using Tapatalk

I think once you shorten up the bottom of your shins and the tops off your thighs, it's going to look fantastic. I would also shorten the elastic strapping from your shoulder bells to the bridges until the two are touching at the top. Also your biceps are sitting too high so drop those down so there is a smaller gap between the top of the forearms and the bottom of those biceps. Sent from my iPad using Tapatalk

Congrats and welcome to the ranks. Sent from my iPad using Tapatalk

Still trying to find it here in Australia, can get it on line. Sent from my iPad using Tapatalk

That thigh is looking much, much better I did think it looked too tight at the bottom. Sent from my iPad using Tapatalk

My sympathy goes out to your wife on the morning sickness, as mine had it real bad when she was pregnant with our daughter. Sent from my iPad using Tapatalk

I recon you would have to keep an eye on it or it will get knock off, $70 gone......... Sent from my iPad using Tapatalk

On a side note, you don't want to overcrowd the inside of your bucket either, in the warmer months you want some form of air circulation or it's going to get real stuffy, real fast even with fans. Sent from my iPad using Tapatalk

I must be lucky cause my bucket virtually touches my neck seal at the front. I have simply used a few pieces of dark grey foam in appropriate places, my 8 year old says she can't see up inside the helmet . Sent from my iPad using Tapatalk

I thought that may have been the case, based on your photo. Looking forward to seeing the new shot. Sent from my iPad using Tapatalk

You can use the other plate with the bolts for basic approval, but if you tend to go for higher levels, they are not accurate. Sent from my iPad using Tapatalk

Maguires also make a plastic polish, Plast X, could be cheaper than Novus, also good on uv yellowing. Sent from my iPad using Tapatalk

For the record, I took all the ridge off one half and most off the other. Sent from my iPad using Tapatalk

Mine is velcroed to the top left side of my helmet, but am considering cutting it down and placing in the chin for better weigh distribution. Sent from my iPad using Tapatalk

Agree with Tolo on both accounts. Much better than Vox as sometimes mine even picks up breathing, and that static burst gets annoying if it goes off too frequently. Sent from my iPad using Tapatalk

It was fine when I logged in to it last night Peter. Sent from my iPad using Tapatalk

As a suggestion, perhaps don't trim quite as much off the bottom, make the tapper of the thigh more gradual rather than so steep as it is in your picture. Then reassess, take another shot and post it up as you have done here. I think it won't look as bad. Is the top tight against your thigh or is there movement? Sent from my iPad using Tapatalk