Leaderboard

Last stock part completed,,, spring plate

I noticed that some time ago with one of the photos so I made them straight and overlapped and the different sizes

I guess we'll all find out in Q4 of 2017 Q1 of 2018 Q2 of 2018 Q3 of 2018 Q4 of 2018 Q1 of 2019!

There was a recent question that asked how to remove split rivets and thought I would share my method, as well as encourage other troopers to post their methods here as well in order to help others that need to tackle this problem. Tools: - Diagonal Cutters "Side Cutters" - Needle Nose pliers or standard pliers depending on the application I prefer using the Diagonal Cutters / "Side Cutters" as the edges of the cutters catch the tails of the rivet without damaging your armor. Using the cutters, squeeze the tails together. Then use pliers to straighten the tails out for removal Good luck Troopers, and many thanks in advance to those who post their methods here. Troopers helping Troopers WHOOO-WAHHH!!! [emoji38][emoji106]

Name: Jorge Alegre 501st ID: TK-34727 FISD Forum Name: trooperGonzo Garrison: NEG EIB: http://www.whitearmor.net/forum/topic/40420-tk-34727-requesting-anh-eib-status-rs-prop-masters-680/?hl=34727 501st Member Page: http://www.501st.com...hp?userID=19548 Armor Maker = RS Prop Masters Helmet Maker = RS Prop Masters Blaster Type = E-11 RS Prop Masters Height = 5' 6" Weight = 135 lbs Boots Maker = Imperial Boots Canvas Belt = RS Prop Masters Hand Plates Type = RS Prop Masters Electronics = Aker, Icomm Neck Seal Type = RS Prop Masters Holster Maker = RS Prop Masters Ab and Kidney armor fit around my midsection has been addressed per EIB application. Thank you for your comments and suggestions!

They will be soon...... Im almost done with the stock setup

Those split rivets look too far in to my eye. I can't remember off the top of my head the correct measurement but the proportioning vs the vertical distances look off to me.

Name: Darren Elkins TK ID: 70670 FISD Forum name: xSCDx Garrison: United Kingdom Garrison http://501st.com/members/displaymemberdetails.php?userID=25411 EIB Clearance: Link Armour Maker: DA Props 2mm standard ABS Helmet maker: DA Props 2mm standard ABS Blaster Type: E11, DoopyDoo - Resin cast Height: 170 cm Weight: 68 KG Boots maker: Loake of London (style 290b) Canvas Belt: ISD Hand plates: Latex ISD Gloves: Rubber Electronics: TrooperTalk Neckseal: ISD Holster: ISD DoopyDoo Build thread: https://www.ukgarrison.co.uk/forum/viewtopic.php?f=139&t=63286 TK Build thread: https://www.ukgarrison.co.uk/forum/viewtopic.php?f=126&t=63854 FRONT: Back: Left: Right: Left Arm Up: Right Arm Up: Helmet: Shoulder Bridges Back: Front: Knee Plate: Forearms Wrist Ends: Ab Plates: Belt: Box: Thigh Ammo Plate: Shoulder Strap design: Cod Piece Neck Seal: E-11: Holster:

Thanks Joseph, I did indeed, it was always my goal to reach Centurion from the off. I was in awe of my fellow troopers, they all looked fantastic.

Basic information. Name: Francisco Rodriguez FISD name: pistolero. 501 st ID 30778 http://www.501st.com/members/displaymember.php?userID=23815&costumeID=12 Spanish Garrison. EIB status: https://www.whitearmor.net/forum/topic/41583-tk-30778-requesting-anh-stunt-eib-statussds723/ Mandatory information. Armor: SDS. Helmet:SDS. Blaster:SDS. Optional. Height: 190 cm. Weight: 94 kg. Age: 46. Boots: CK. Canvas Belt: traumtrooper. Spanish garrison. Neack seal: Traumtrooper. Spanish Garrison. Holster: autism school (PAUTA) Madrid spanish. handplates: Antillis. Spanish Garrison.

Congrats Jared and welcome to the centurion rank!

Whoop!! One of my last expected deliveries - and it's a good one. I have just received my TRamp. I've had a quick play and it seems really good. Will give it a proper test later and report back. For those that haven't seen it before, it's essentially an Aker speaker/amp with all the clever stuff built in. In built audio loops, many voice presets and loops for TK, Vader, Fett, droids etc... Comes with two mics, USB charging cable, strap, 3.5 to 3.5mm jack (not actually required for this setup, just comes with the aker I think), and I opted for the remote version. This allows samples to be triggered, static bursts on request, volume adjustment etc., or you can just talk through it and enjoy the trademark pops and bursts. Sent from my iPhone using Tapatalk

So, let's build a thermal detonator. Kids can play with explosives. Can't they? For reference, here's my TD I started thinking, "what would be best for the cylinder shape"? PVC would be great but probably too heavy, this is only foam armor after all. So, the trusty paper towel roll was the winner. Luckily I had one in the kids craft/marker drawer that I'm sure would have ended up as a pirate telescope but now will be transformed in the imperial armory a.k.a. my basement. I determined the length based on the size of my TD relative to a part of my chest armor then used that as a rough approximation for the scaled down version. The tube is pretty flimsy and I'm sure my son will be playing with this thing so it needed to be beefed up. I glued some scrap pieces of foam into the tube to give it some rigidity. The foam strips run full length. Then I cut 4mm foam to wrap the outside of the tube and used contact cement to glue it on. Don't forget to glue the seam too. I cut out some circular shapes to cap off the tube ends. 4mm again. Not the best circle but close enough. Glue these on. Once the ends were glued I cut some 2mm foam strips which would simulate the end caps. Cement these into place. More 2mm foam for the control panel plate. To make the rectangular piece I used some 4mm foam. I marked out some lines and cut half way thru along each line. Then I hit it with the heat gun to open up the seams. It didn't look quite right so I went back and too ok additional 45 degree cuts along each joint. Then another heat gun treatment. Here's the final TD, minus the clips. To do those I bough aluminum strip metal at the local hardware store. Just need to cut it to length and bend it into shape. Once the TD is painted, I'll attach the clips, probably with the hot glue gun.

i love the spring plate

So awesome.

ONE DAY LEFT! Also, just wanted to say a big THANKS to all of you who participated in this. These stories are amazing, and many bring back some of my own memories. The Attaches have quite a job on front of them choosing a winner. Best of luck to all of you!

comfy-ness", I like it

The little extra won't make too much of a difference, my ears tend to catch when putting on my Hero version, Stunt helmet not so much, if you can get in and out without seeing blood you should be fine

Got some great news and if all goes to plan and the postal service uses the force my big box could arrive at the end of next week #fingers#crossed

Hello FISD! I came across this charity drive that is being hosted by Walts Trooper Factory. They are offering a patch and a sticker which will help support Team Rubicon as they volunteer their time to aid the victims of Hurricane Harvey in Texas. I know many of you have probably already donated time and money to help our brothers and sisters in Texas but in case you haven't and you are looking for a way to help then here is a way to do so. Below are the informational links. www.waltstrooperfactory.com www.teamrubiconusa.org Troopers Helping Troopers

You did your first troop as Centurion? WOW! Sounds like you set the bar really high for for your fellow UKG Troopers, Darren. Outstanding job, brother, and a big WELCOME to level 3!!!!

Armor-AM 2.0 Helmet-AM 2.0 Blaster- 3D printed EIB post TK10596 requesting EIB status AM 2.0 (ESB) [APPROVED] https://r.tapatalk.com/shareLink?share_fid=44557&share_tid=41877&url=https://www.whitearmor.net/forum/index.php?/topic/41877-TK10596-requesting-EIB-status-AM-2%2E0-%28ESB%29--%5BAPPROVED%5D&share_type=t Optional Height- 5'10" Weight-190lbs Boots-TK Canvas belt-Trooper bay Hand plates-AM 2.0 Electronics-TRamp with ukswrath cooling fans. Neck seal-Trooper bay Holster-Trooper bay Front Back Left Right Forearms Cod Butt Ammo pack Knee plate Inside strapping Shoulder bridge back Should bridge front Hand plates Gloves Belt back Neck seal Thermal detonator Holster Helmet front Sides Back S trim Lens color Hovi tips Blaster sides Ab details So I raised the belt to just cover the bottom ab buttons. I trimmed the 4 button set down a little and made sure belt wasn't sagging as per requested in my EIB submission. Have a great day and thanks for the advise. Sent from my iPhone using Tapatalk

Trooper Info Name: Sarah Bailey Forum name: Alay Garrison: Connecticut Garrison Legion Number: 20466 501st Legion Member Page: http://501st.com/members/displaymemberdetails.php?userID=22318 Height: 5' 8" Weight: 125lb Costume Information Armor: AP Authentic Props Helmet: AP Authentic Props Blaster: SE-14r by Shawn Morgan Boots: ImperialBoots Canvas belt: TKittell Hand Plates: AP Kit Neck Seal: Veedox Pouches: Anthony Bailey EIB Application Thread: Front Left Left (Arm Raised) Left (Detail) Right Right (Arm Raised) Right (Detail) Back Helmet Detail Green Eyes S-Trim Ab details (Belt lowered as per EIB suggestion... I was actually wearing it upside down last time so the snaps were in the wrong spot... heh) Backpack details (redid weathering as per EIB suggestion. Dry brushed with silver many of the screws/raised elements. Shadowed up the earlier silver splatches to either remove or fade. Added more charcoal weathering) Gloves Shins Thigh (adjusted as per EIB) Belt connections Neckseal Rivet Alignment Forearms Removed return edge Interior strapping SE-14R Backwards scope (as per promotional reference shot, no wonder stormtroopers always miss) Pauldron weathering My ugly mug Requisite action shots Thanks for taking the time to review! I appreciate any and all feedback ~Sarah

Name: Gary Hill 501st ID: 11146 FISD: sentry71 Midwest Garrison Mandatory Information Armor = Authentic Props (AP) Helmet = AP Blaster = Hyperfirm E11 EIB: https://www.whitearmor.net/forum/topic/36499-tk-11146-requesting-anh-stunt-eib-status-ap-554/ Optional Height = 5' 7" Weight = 175 lbs Boots = Imperial Boots Canvas belt = TKittell Hand Plates = Sonnenschein Neck Seal = Geeky Pink Holster = Darman Edited to remove photo links... will reupload and relink ASAP. Front Back Left Right Hand plates Shoulder Thigh pack Sniper knee Drop box back / holster Cod/posterior Helmet front Helmet back Helmet left Helmet right Hovi tip Lens color S Trim Ammo belt (45 degree corner) Neck seal Blaster left Blaster right Bottom Thermal Det Action shot