Jump to content

TKC-69901 Requesting EIB status ( RS Props ) 1010


Ruck

Recommended Posts

Personal Info:

Name: Scott Ruckert

Call sign: Ruck

501st ID: TX / TKC 69901

 

Armor Info:

Armor Maker:  RS Props

Helmet: RS Props ( S neck trim )

Neck seal: RS Props

Under suit: RS Props

Rubber gloves and silicon hand plates:

RS Props

Canvas belt: RS Props 

Boots: RS Props 

All seams over lap ( no cover strips )

 

 

 Helmet Front:

VHhmS0F.jpg

 

Helmet Front Mic tips / Vocdor: 

voGrtxi.jpg
 

Helmet Right Side:

aaFE6bL.jpg
 

Helmet Right Side Ear screws:xMN5ti1.jpg

 

Helmet Rear:

H913tqt.jpg
 

Helmet Left Side:

aOfZRMA.jpg

 

Helmet Left Side Ear Screws:

dT4t6dF.jpg

 

S trim / Green lenses: 

LBlDYoC.jpg


Armor Front: 

EqyQwFJ.jpg


Armor Chest and Ab:

HZ15Xlw.jpg
 

Ab Buttons:

m4oMT9w.jpg
 

Armor Front Legs:

8L1p3LP.jpg

Armor Side Right:

nnvVs0R.jpg

 

Armor Side Right Ab / Kidney:

PA8JfSP.jpg
 

Armor Right Side Legs:

HSvt0fn.jpg
 

Armor Rear:

k0S6kis.jpg

 

Armor Back / Kidney: 

tNrY3Mi.jpg
 

Armor Rear Legs:

652JUlr.jpg

 

Armor Left Side:

N1nNPr1.jpg

 

Armor Left Side Kidney / Ab:

G7mRShO.jpg

 

Armor Left Side Legs:

dunsrbU.jpg
 

Sniper Plate: 

fj9sfWX.jpg

BFm5pkX.jpg

 

Ammo Belt inside Right Leg: 

JKabQnL.jpg
 

Ammo Belt Outside Right Leg: 

hnpvYd1.jpg

 

Boots:

2Z6Zmpq.jpg

 

Thermal Detonator Game Version Front: 

OW11pfL.jpg

 

Thermal Detonator Game Version Rear:

wJGSE3X.jpg

 

Rubber Gloves / Silicon Hand Guards: 

joL1rBq.jpg

 

Neck Seal: 

lSIbxVo.jpg

 

Forearms ( no return edge ) 

uMjSWxo.jpg

 

No Rivets / Snaps in Cod or Posterior:

eXpHBug.jpg 

 

Inside Strapping:

wQQ2Hmw.jpg 
 

Proper Split Rivets Used Throughout:

GXc7rLa.jpg
 

Belt Front:
wrhtmIE.jpg
 

Belt Front:

cDMAhIS.jpg

 

Belt Left Front ( Buttons on outer edge, ammo boxes lined up with edge of ammo belt, canvas belt aligns with 45 * inside angle, canvas belt has 4 split rivets 

cSDcjgz.jpg

 

Belt Front Right: ( same specs as Front Left ): 

rHwa1XB.jpg

 

Belt Rear ( With Closed Drop Boxes ):

Bj2lXqq.jpg

 

Belt Rear Left ( Closed Drop Box ):

2SnNdop.jpg

 

Belt Rear Right ( Closed Drop Box ) 

kTScU90.jpg
 

Weaponry:

SK Game Version Lightsaber: 

fHsNiaY.jpg

 

RIpx0A2.jpg
 

hlyGFSD.jpg

 

aFiny39.jpg4xPGU5j.jpg

 

Bucket Off Photo:

dD4JXTB.jpg


Action Pose ( 1  The Ruck):

StkA4Cq.jpg

Action Photo ( 2 ):

96T6fuh.jpg
 

Action Photo ( 3 ): 

 

KzFhf8Y.jpg
 

Action Photo ( 4 ): 

QCyJLJm.jpg
 

END TRANSMISSION......

 

Link to comment
Share on other sites

Thank you both.  I hope my work is up to the standards of the DO.  I’ve followed expert advice to get this armor up to snuff hope my work is good enough.  

  • Like 2
Link to comment
Share on other sites

Hi Scott .  I'll be the D.O.  doing your EIB review.  At this starting point I'll need you to add some datil photos:

 

 

1-The Crl states for Basic Approval about Shoulder Bridges:    

 

These shall be securely mounted in front and may free float in back.

 

Looking at your provided photos, It couldn't be appreciated if the shoulder bridges has some kind of Velcro attached, could you please add a close photo of their back  inner side and the back plate's shoulder detail to check it?

 

 

                                                                                                                                  Reference images

Def1Xth.jpg?1       ItY51T5.jpg?1    Jg2iyOG.jpg?1

 

2- The crl also for Shoulder Bridges for L2  states:

 

Shoulder straps shall not have a flat end at the ends of them. They shall be ribbed 100%.

 

Could you please add a close photo of the back section of the shoulder bridges to check they have no flat end? something like the reference bellow.

 

 

8MDVjQ0.jpg?1

 

thank you.  :salute:

 

 

 

 

 

 

 

 

 

  • Like 1
Link to comment
Share on other sites

Shoulder straps:

Trimmed to the end of the last rib no flat spot 

Left shoulder Strap:

x2m7SPC.jpg

 

Right Shoulder Strap:

dtYol9D.jpg

 

 

Edited by Ruck
Link to comment
Share on other sites

Hi Scott, and thank you for the additional  photos and for your patience.

 

A quick fix will be needed to your shoulder bridges and it's to trim a bit the back section to match the crl requirement.

 

rear section

 

RH729qY.jpg?2  SA9Q8OV.jpg?2

 

References  

 

44bpDOl.jpg?1   YMMURYx.jpg

 

 

Almost there Trooper.  

 

 

 

Link to comment
Share on other sites

With the little ABS piece I made underneath I pushed the hot ABS over it to form another ridge so my shoulder straps weren’t too short: 
LBcO5HM.jpg

Edited by Ruck
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...