gmrhodes13

ONLY 10 spots remaining . Last approved EIB #990 Ueli "carcharoth" TK19844

Hello and welcome to the ranks trooper

SE14R reference pix, restored by gmrhodes13 SE14R build, restored by gmrhodes13 SE14R greeblies, restored by gmrhodes13 SE14R holster, restored by gmrhodes13 Need help about SE14R, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/9925-se-14r-eu-reference-pix/ https://www.whitearmor.net/forum/topic/25093-se-14r-build/ https://www.whitearmor.net/forum/topic/28078-se-14r-greeblies/ https://www.whitearmor.net/forum/topic/35912-need-help-about-se-14r/ https://www.whitearmor.net/forum/topic/28745-se-r14-holster/

Images updated

Real world has affected a lot of people, good to see you back, hope things improve for you and all of us

Nice work trooper, a couple of suggestions. Watch the spacing of your armor, thigh is hitting the butt plate, it is also being pushed backward leaving a gap in the sides, biceps are also not equal Belt boxes are not quite aligned with the end of the belt You are probably just on the edge of paint on leaving the teeth Frown is painted gray and does not leave the teeth area., wouldn't hurt to take off a little paint but may not be picked on. TD screws should be black, there should be no gap from the end caps to the clips, also screws on the clips could be closer to the panel. There is a little gouged out area under your cover strip, you could add a little ABS paste You will need photos of the sides of your sniper plate. Also thigh ammo strip rivets inside and out. Right side top ab snap Great work and good luck with approval

This will make a few people happy, Commander Pyre Black Series realistic version, coming to Target US

Note: head here for your centurion certificate

Could very well be, there have been months in the past were we have only seen 2 or 3 applications. I know some are just waiting on last pieces, approval and access. I really hope some aren't waiting for the 1000th, that's not what FISD is about, troopers helping troopers, not glory hunters

Looking good. For a couple of my builds I added some snaps on the triangle section of the rear harness, keeps the backplate up well. Cods on the R1's are pretty big, yours as is looks a little small height wise when you compare to screen images Butt plate looks good. You could reduce the V area if you wanted more movement, notice on the screen reference the V alignment to the rectangle recess area This image of the cod looks better in this image, remember too that the thighs are a lot lower with R1 compared to OTTK, they have a big black area showing I have found that a lot of Jim's kits do need quite a lot of trimming especially on thighs, must be some big thighed models around. Feels great actually putting pieces on

Incinerator trooper plasma canon flamethrower, restored by gmrhodes13 Custom flamethrower, restored by gmrhodes13 flamethrower V2, restored by gmrhodes13 flamethrower, restored by gmrhodes13 My plasma rifle build, restored by gmrhodes13 Plasma rifle rough draft, restored by gmrhodes13 Flamethrower question, restored by gmrhodes13 flamethrower speed build, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/14958-incinerator-trooper-plasma-canon-flamethrower/ https://www.whitearmor.net/forum/topic/12214-custom-flamethrower/ https://www.whitearmor.net/forum/topic/12504-flamethrower-v2/ https://www.whitearmor.net/forum/topic/10547-flamthrower/ https://www.whitearmor.net/forum/topic/32403-my-plasma-rifle-build-0/ https://www.whitearmor.net/forum/topic/10867-plasma-rifle-rough-draft/ https://www.whitearmor.net/forum/topic/15582-flamethrower-question/ https://www.whitearmor.net/forum/topic/15205-flamethrower-speed-build/

Congratulations trooper and welcome to the ranks, good luck with your EIB application

$14,000 for a 501st approved costume, if only we could all sell ours for this, I'd be pumping out a set of armor every week At first I was like ok but it's not Mandalorian specific era armor BUT the Propstore has mentioned several times it's a costume created by the 501st and appeared throughout the series so the buyer should know what they are getting. At the end of the day it's a nice payday for the member and it did appear on screen and I'm sure the purchaser is happy. The helmet, those ear screws, "he cringes"

Looking forward to seeing the finished photos

Congratulations trooper and welcome to the Centurion ranks

Just watch the elbow sections of the forearms as they are also different between TFA and TLJ Nice work

Certainly does

Looking good. I also noticed blue in the rectangle from a few threads but I think that was before other references became available. Grey or black seems to be the way to go, still haven't seen a definitive image so I'd stick with grey for the time being.

my new t21 new body barrel detail, restored by gmrhodes13 my new batch of T21's, restored by gmrhodes13 Yoshixs T21 spool68, restored by gmrhodes13 Incinerator plasma cannon screen grabs, restored by gmrhodes13 V3 flamethrower, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/20537-my-new-t-21s-new-body-barrel-detail-and-3-stain-choices/ https://www.whitearmor.net/forum/topic/19547-my-new-batch-of-t-21s/ https://www.whitearmor.net/forum/topic/38623-yoshixs-t-21-w-spool68s-kit/ https://www.whitearmor.net/forum/topic/18342-incinerator-plasma-cannon-sceen-grabs-4-images-tfu/ https://www.whitearmor.net/forum/topic/13678-v3-flamethrower/

Lewis manuals, restored by gmrhodes13 MG15 RT07C reference, restored by gmrhodes13 MG15 tutorial, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/27023-lewis-user-manuals/ https://www.whitearmor.net/forum/topic/21474-mg-15-rt-97c-reference/ https://www.whitearmor.net/forum/topic/10709-mg-15-tutorial/