gmrhodes13

Nothing like a nice BBB of armor to start trimming. Although there isn't my h in the way of Phasma references you will find a lot of items are similar between Phasma and FOTK's, some great reference material can be found in the gallery sections https://www.whitearmor.net/forum/gallery/category/20-fotk-reference/ Tony has a great FOTK build showing step by step assembly, although his AB boxes were numbered you should still be able to tell what goes were by sizes

The DO's try to use consistent clear images when possible although there's always the odd trooper that can be different. It will really be up to the DO's to call on so don't stress for the time being. Even the "Han" snap is a little far away from the edge but as you say it is a commission so again it's up to the DO's That's a much better gap from handplate to forearm

Here are some references, you will notice that the sides do have a slight curve from about 1/2 way upwards curving out. Also the sides meet with the cod bulge sides Your butt plate is very rounded, again compare with some references and you will notice they are quite angular and straight lined You can find more images in the gallery sections for reference https://www.whitearmor.net/forum/gallery/category/28-r1-tk-reference/

It's very hard to get scratches off lens material, you could use some ultrafine sandpaper @2000 grit, or even some cutting polish, may be a little more forgiving

Nice fixt on those thighs, coming along nicely

Nice work trooper, a couple of suggestions you may want to take on board before the DO's get to work Your thigh ammo strip rivets are very close the the edge You may want to move your handguards further forward they appear to be hitting your forearms. Also add some foam behind your sniper plate to help hold it away from your thigh or it may get caught when walking and bending You may want to trim the curve from the sides of your sniper plate example Just watch your sides too as in one of your images the AB and Kidney are misaligned at the top on your side image Can you also post an image of your right side top ab snap Good luck with approval

Congratulations Basti and thank you for sharing

ANH Holster, although we see Stunt holsters on most Stormtroopers, strap size and color varies from trooper to trooper as well as position on belt. Majority having long straps Approximate guide Hero Holsters, the following are what are seen on Han and Luke, E-11 style with the 4 rivet attachment, although slightly different Approximate guide A nice shot of Han and Luke both with E-11's holstered and Han carrying the DLT19. Note the droop on Han's belt from the weight Incidentally how many of you noticed when TK421 (Luke) comes out of the falcon wearing the comlink and grappling box he is also sporting a detonator? RS Holster worn by Hero helmet trooper below, mid attachment, believed to be a rebel DH-17 holster put on a TK belt (incorrectly). Also note the stitching is on the left (front) of the holster and the standard E-11 is on the right (back), it is shorter than the E-11 and also angled on the bottom. At first only believed to be worn by 1 trooper we have the image below showing 2 troopers sporting this style of holster Very easy to spot as the holster is a lot shorter than an E-11 holster and slightly angled on the bottom Hero Promo, short like the RS holster also stitching on the left (front) BUT with a cut-out section and SE-14R in the holster, once again you can see it is a lot shorter than an E-11 holster as it is high on the thigh. This could very well be one of the RS style holsters modified with the cut out seen below. 4 rivet attachment as you can see the two rivets on the one strap below No Holster and of course there has to be someone who's been in a rush to dress and forgotten his holster (note not approvable) For anyone wishing to make their holster removeable IMAGES RS Props belt comparison Luke belt references

Congratulations trooper and welcome to the EI ranks

ONLY 10 spots remaining . Last approved EIB #990 Ueli "carcharoth" TK19844

Hello and welcome to the ranks trooper

SE14R reference pix, restored by gmrhodes13 SE14R build, restored by gmrhodes13 SE14R greeblies, restored by gmrhodes13 SE14R holster, restored by gmrhodes13 Need help about SE14R, restored by gmrhodes13 https://www.whitearmor.net/forum/topic/9925-se-14r-eu-reference-pix/ https://www.whitearmor.net/forum/topic/25093-se-14r-build/ https://www.whitearmor.net/forum/topic/28078-se-14r-greeblies/ https://www.whitearmor.net/forum/topic/35912-need-help-about-se-14r/ https://www.whitearmor.net/forum/topic/28745-se-r14-holster/

Images updated

Real world has affected a lot of people, good to see you back, hope things improve for you and all of us

Nice work trooper, a couple of suggestions. Watch the spacing of your armor, thigh is hitting the butt plate, it is also being pushed backward leaving a gap in the sides, biceps are also not equal Belt boxes are not quite aligned with the end of the belt You are probably just on the edge of paint on leaving the teeth Frown is painted gray and does not leave the teeth area., wouldn't hurt to take off a little paint but may not be picked on. TD screws should be black, there should be no gap from the end caps to the clips, also screws on the clips could be closer to the panel. There is a little gouged out area under your cover strip, you could add a little ABS paste You will need photos of the sides of your sniper plate. Also thigh ammo strip rivets inside and out. Right side top ab snap Great work and good luck with approval

This will make a few people happy, Commander Pyre Black Series realistic version, coming to Target US

Note: head here for your centurion certificate

Could very well be, there have been months in the past were we have only seen 2 or 3 applications. I know some are just waiting on last pieces, approval and access. I really hope some aren't waiting for the 1000th, that's not what FISD is about, troopers helping troopers, not glory hunters

Looking good. For a couple of my builds I added some snaps on the triangle section of the rear harness, keeps the backplate up well. Cods on the R1's are pretty big, yours as is looks a little small height wise when you compare to screen images Butt plate looks good. You could reduce the V area if you wanted more movement, notice on the screen reference the V alignment to the rectangle recess area This image of the cod looks better in this image, remember too that the thighs are a lot lower with R1 compared to OTTK, they have a big black area showing I have found that a lot of Jim's kits do need quite a lot of trimming especially on thighs, must be some big thighed models around. Feels great actually putting pieces on