gmrhodes13

Congratulations and welcome to the ranks

Good luck, hopefully it’s not a long wait. Looking good.

If you have used E6000 then they will come apart with a little bit of gentle force, then you can clean the glue by rubbing with your thumb or some rags.

Can be as simple as just a belt with loops of elastic or nylon attached to suspend the thighs

Congratulations trooper

Congratulations

You can adjust the size of photos in a lot of programs and apps, depends on what you are using, once reduce you can then upload and add to the post

The image was posted as an approximate guide, to show the knee ammo strip. But in regards to the belt, from the CRL L3: The corners of the plastic ammo belt shall be trimmed at a 45 degree angle that that meets the outer edge of the cloth belt.

Any chance you would have some references we could add to the galleries, seems a lot of images from the older ROTJ posts are now inaccessible

Star Wars Resistance Star Wars Resistance is the new animated television series inspired by Japanese anime and produced by Lucasfilm Animation. The series premiered on Disney Channel on October 7, 2018, and later debuted on Disney XD in the United States and worldwide. The series is set decades after the events of Return of the Jedi, in the era of the Star Wars sequel trilogy. It follows Kazuda Xiono, a pilot who is recruited into the Resistance to spy on the growing threat of the First Order. The series begins six months before The Force Awakens and will eventually cross over with it. Created by: Created by Carrie Beck, Dave Filoni, Kiri Hart. Plot: Kazuda Xiono, a young pilot for the Resistance, is tasked with a top secret mission to investigate the First Order, a growing threat in the galaxy. SPOILERS AHEAD V V V V V So far episodes 1 to 4 have been a very slow, there has been the appearance of a new First Order Interceptor and red Pilot (with a very strange helmet mashup design) and of course First Order Stormtroopers (why the long face troopers) http://digitalspyuk.cdnds.net/18/41/768x438/gallery-1538992089-star-wars-resistance-tie-interceptor.jpg We also see Phasma. A throw back to original Stormtrooper's with a helmet and armor worn by one of the pirates in episode 3. One character yet to make an appearance, the Gold Stormtrooper "Commander" http://cdn.epicstream.com/assets/uploads/newscover/760x400/153869534904_-_Star_Wars_Resistance,_Commander_Pyre.jpg Hopefully the pace will pick up in the coming episodes. Star Wars Resistance has received 91% on Rotten Tomatoes, average audience score 80% happy. Also received an average 5.0 out of 10 on IMDb

I use the bottom of a spray can and trace around. Just as a guide Some other info: https://www.whitearmor.net/forum/topic/38020-ammo-pack-to-thigh-whats-the-correct-alignment/

Check out Tony's build thread https://www.whitearmor.net/forum/topic/35086-uswraths-anovos-tk-build-stunt/?page=5 Gallery references here https://www.whitearmor.net/forum/gallery/album/23-knee-ammo-pack-a-new-hope/

I used snaps behind the rivets and made two strips of abs with the opposite snaps and elastic between those, so that whole section can be removed from the armor, mainly did this because of trying to fit in a hard plastic suitcase for air transport. Rivets can can be there functioning or not.

ANH was the first one I had seen on the big screen so always had a special place in my heart, plus with one costume with some additional parts you can do a few others

If you are 501st approved and a Stormtrooper you have to have an access upgrade :

Congratulations once again Jason, welcome to the ranks and FISD trooper

Never too late to start, least you had time to do some research Good luck with the build

In regards to the ROTJ Paul posted these two images in another thread: This is an original ROTJ armour on display. And this is in the LFL archives. From the same display as the first image, the knee ammo strip has the middle rivet Bit hard to make out what was used on the sides to attach the strip as it is covered by tape and unclear in the other side image.

Normally the large tab and between 3 to 5 of the smaller tabs, ideal being @ 4 1/2

Nice work, I don't see any hold ups, good luck with approval

White soles Sniper plate - CRL says one pop style rivet, but my understanding is that it's one on each side. One of the various shin photos in the CRL shows this. This is being addressed currently, should be a CRL update soon, one either side painted white, Also evidence some had a rivet unpainted in the middle of the knee ammo strip, you can see the back of the rivet and washer inside the thigh No kidney/ab rivets

https://www.whitearmor.net/forum/topic/42866-how-to-make-abs-paste/

Just a shame it's a little on the thin side and is susceptible to cracking over time

I have two sets, both have some distortion but there are areas you can see through fine, not as bad as most make them out to be

Looking smart, good luck with approval