kylebeagle[TK] Posted November 10, 2013 Report Share Posted November 10, 2013 Mandatory Information: Armor Maker = RS | ABSHelmet Maker = RS | ABSBlaster Maker = SciFire | Hyperfirm Optional: Height = 5' 11"Weight = 205#Boots Maker = TKBootsCanvas Belt = RSHand Plates Type = RS | AccurateElectronics = Aker AMP | Standard Set UpNeck Seal Type = Trooper BayHolster Maker = RS ---------- Centurion Suggestions - This is a totally stupid one... but I suggest removing the paint from the two snaps in the cod. - If possible tighten up the strapping between the parts on your back. - Your thighs should come up to get away from your shins and reduce black space. I would normally say raise the ab (my answer to everything) but if you've got the screen accurate strapping your ab plate won't be able to come up much. Can you hork up on whatever is holding your thighs up? ---------- Full Body Front - Arms at side Back - Arms at Side Left - Arm Raised Right-Arm Raised Armor Details Ab/Kidney Attachment - Button Orientation Butt/Kidney - Fixed = Yes Hand Plates Shoulder Bridge Back Shoulder Bridge Front Back/Chest Connection Thigh Pack Attachment Knee Plate Drop Box Back / Belt Back Cod and Butt Plate Attachment Helmet Detials Front Side Left/Right Back Hovi Mic Tip Details Lens Color (Backlit) S-Trim Blaster Details Blaster-Right Blaster-Left Accessories Detials Neck Seal Thermal Detonator - Back Holster Attachment Quote Link to comment Share on other sites More sharing options...
captsafe66[Admin] Posted November 10, 2013 Report Share Posted November 10, 2013 Looks Sharp! Good Luck!! Quote Link to comment Share on other sites More sharing options...
Rezablad3[TK] Posted November 10, 2013 Report Share Posted November 10, 2013 Another one for GGG..... Quote Link to comment Share on other sites More sharing options...
Cantina Security[501st] Posted November 11, 2013 Report Share Posted November 11, 2013 So this is RS, mostly? Are you happy with the fit? Quote Link to comment Share on other sites More sharing options...
TK bondservnt[501st] Posted November 11, 2013 Report Share Posted November 11, 2013 I'd say this one is a GO! Quote Link to comment Share on other sites More sharing options...
kylebeagle[TK] Posted November 11, 2013 Author Report Share Posted November 11, 2013 So this is RS, mostly? Are you happy with the fit? Yes. I am very happy with the fit and quality. Quote Link to comment Share on other sites More sharing options...
kylebeagle[TK] Posted November 11, 2013 Author Report Share Posted November 11, 2013 I'd say this one is a GO! Thank you for the support. Quote Link to comment Share on other sites More sharing options...
kylebeagle[TK] Posted November 11, 2013 Author Report Share Posted November 11, 2013 Looks Sharp! Good Luck!! Thank you... Hoping all is in order and meets standards. Quote Link to comment Share on other sites More sharing options...
The5thHorseman[501st] Posted November 11, 2013 Report Share Posted November 11, 2013 (edited) I'd say there's some points to work on. First, it's nice to see your side junctions looking perfect now, good job on that ! Now the few things i would improve: - Hyperfirm put really too much brass on their scopes. You should reduce the weathering down with black paint. - Also you could clean up the molding lines on the blaster (e.g: on the end cap/ the top of the scope, etc...) - Your shoulder bells could be more closed on the front. For proper shoulder belles like RS ones, you should be able to close them more than they are right now. The Closer the Better ! - Your right thigh could be brought up a little (again:p). - What's the holster tan straps width ? RS has the tendency to make them too wide. They should be around 20mm. - Also on the holster, you have fastened the top of the strap to hold the blaster really off-centered. i don't know if it matters but i've always see them fastened to the middle. And this strap should go through the holster and be fastened by the side facing the thigh. And lastly a cosmetical one: i would switch the neck trim junction to the front of the helmet as the gap between the two lips is rather big. This way it would be hidden Good luck with your approval ! Edited November 15, 2013 by The5thHorseman Quote Link to comment Share on other sites More sharing options...
vecspeed12 Posted November 12, 2013 Report Share Posted November 12, 2013 Lookin good! Quote Link to comment Share on other sites More sharing options...
kylebeagle[TK] Posted November 12, 2013 Author Report Share Posted November 12, 2013 Lookin good! Thank you! Quote Link to comment Share on other sites More sharing options...
Darth Aloha[Admin] Posted November 15, 2013 Report Share Posted November 15, 2013 Approved. Congrats trooper! -Eric Quote Link to comment Share on other sites More sharing options...
Clamps[TK] Posted November 15, 2013 Report Share Posted November 15, 2013 Congrats and welcome to Centurion! Quote Link to comment Share on other sites More sharing options...
kylebeagle[TK] Posted November 15, 2013 Author Report Share Posted November 15, 2013 Approved. Congrats trooper! -Eric Thank you!! I am honored. Congrats and welcome to Centurion! Thank you. I greatly appreicate your congrats. Quote Link to comment Share on other sites More sharing options...
Jancelot[TK] Posted November 15, 2013 Report Share Posted November 15, 2013 Well done and congrats! Quote Link to comment Share on other sites More sharing options...
Rezablad3[TK] Posted November 15, 2013 Report Share Posted November 15, 2013 Congrats trooper.... Quote Link to comment Share on other sites More sharing options...
kylebeagle[TK] Posted November 15, 2013 Author Report Share Posted November 15, 2013 Well done and congrats! Congrats trooper.... Thank you both!! Quote Link to comment Share on other sites More sharing options...
vecspeed12 Posted November 15, 2013 Report Share Posted November 15, 2013 awesome work Kyle! Quote Link to comment Share on other sites More sharing options...
Marc[TK] Posted November 15, 2013 Report Share Posted November 15, 2013 congrats Quote Link to comment Share on other sites More sharing options...
kylebeagle[TK] Posted November 15, 2013 Author Report Share Posted November 15, 2013 awesome work Kyle! Thank you for the acknowledgement as well as the encouragement to submit for both EIB and Centurion designations. congrats Thank you sir! Quote Link to comment Share on other sites More sharing options...
Haribon72[TK] Posted January 27, 2014 Report Share Posted January 27, 2014 Congrats on your CL approval!!! Quote Link to comment Share on other sites More sharing options...
kylebeagle[TK] Posted January 27, 2014 Author Report Share Posted January 27, 2014 Thank you Walter... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.