RocketFinch[TK] Posted January 9, 2008 Report Share Posted January 9, 2008 (edited) Help. Newbie with a problem. I was working on my AP helmet and got a crack in one of the dimples for the mic tips. The plastic was thin in this area to begin with, now this. I am worried about supporting the mic tip. I am afraid if I drill the hole and add the mic tip that it will just tear. Is there anyway to repair and strengthen this area? Edited February 12, 2021 by gmrhodes13 photos updated gmrhodes13 2021 Quote Link to comment Share on other sites More sharing options...
DesTROYer[501st] Posted January 9, 2008 Report Share Posted January 9, 2008 You could try reinforcing it from behind with a two part epoxy, by building up a thick paste behind the dimple. But also I would get on the email to AP and see if they will replace it. Quote Link to comment Share on other sites More sharing options...
Runnriottt Posted January 9, 2008 Report Share Posted January 9, 2008 Hmmm... Could use superglue to firm up the back, let it dry and then drill. Or Glue on a small piece of ABS, to the back, then drill from the front. If you are useing a dremel, High speed man... less chance of grabbing. I start a hole by useing an Icepick to make a center. Then the drill wont wonder. Tips arent all that heavy, and there pretty shielded from being bumped by the helmet design anyway. I hpe that helped a little... Quote Link to comment Share on other sites More sharing options...
trooper1[TK] Posted January 10, 2008 Report Share Posted January 10, 2008 Hey dude, I just recieved my AP armor today and it is thin also. I emailed AP today and got a reply that this is normal, thin that is, I dont have a crack but there is a weak divet. I rough cut all of my armor out in about 4 hours and have went ahead and did the two part epoxy thing and put a thin coat all over the back to reinforce it. It seems to have worked. I havent drilled it yet but it is much stronger. Quote Link to comment Share on other sites More sharing options...
RocketFinch[TK] Posted January 10, 2008 Author Report Share Posted January 10, 2008 Thanks for the ideas. From what I have read around here AP helmets can be thin in some places, like the place I had a problem. I think that I will try the epoxy and see if I can reinforce it. With the mic tips in place I don't think the crack will be noticeable and the epoxy should help with the strength. Quote Link to comment Share on other sites More sharing options...
Smitty Posted January 10, 2008 Report Share Posted January 10, 2008 Use large washers on the back of the hovis, inside the helmet.It will give it more structural support. Quote Link to comment Share on other sites More sharing options...
troopermaster Posted January 10, 2008 Report Share Posted January 10, 2008 Better still, use a rubber washer Quote Link to comment Share on other sites More sharing options...
Smitty Posted January 10, 2008 Report Share Posted January 10, 2008 Better still, use a rubber washer I didnt think you were supposed to reuse those. du-dump tshh! Why rubber over metal washers? Quote Link to comment Share on other sites More sharing options...
Bigturc Posted January 11, 2008 Report Share Posted January 11, 2008 Do not worry, I have thin area too on my bucket, and never even reinforced it myself. Never caused me any problem with the helmet yet, and I've manipulated it more often then not! Quote Link to comment Share on other sites More sharing options...
TK-4510[501st] Posted January 11, 2008 Report Share Posted January 11, 2008 Try this too possibly. I have taken a small 1x1 inch square of t-shirt material and soaked it good with super glue. Then just spread it over the back of the cracked area and work out the bubbles. In about 5 minutes it will be rock solid. I call it miniature fiberglass repair dont get that stuff on your fingers though!!!! Quote Link to comment Share on other sites More sharing options...
TK-4510[501st] Posted January 11, 2008 Report Share Posted January 11, 2008 Try this too possibly. I have taken a small 1x1 inch square of t-shirt material and soaked it good with super glue. Then just spread it over the back of the cracked area and work out the bubbles. In about 5-10 minutes it will be rock solid. I call it miniature fiberglass repair dont get that stuff on your fingers though!!!! Quote Link to comment Share on other sites More sharing options...
Smitty Posted January 11, 2008 Report Share Posted January 11, 2008 An idea so good he had to say it twice Quote Link to comment Share on other sites More sharing options...
Ketariniii Posted January 11, 2008 Report Share Posted January 11, 2008 you can also get som epoxy paste and roll it out with a round object (something you dont care about) and use a think sheet of that to reinforce it from the inside. Quote Link to comment Share on other sites More sharing options...
troopermaster Posted January 11, 2008 Report Share Posted January 11, 2008 Why rubber over metal washers? Well, a rubber washer would give you some amount of 'play' if the mic tips were knocked and not crack the thin area. The mic tip area is notorious for being thin due to the shape when the plastic is pulled into the cavitiy. You could try heating up a piece of scrap ABS and applying it over the crack on the inside. This should at least give you a bit more strength when glued in place. Quote Link to comment Share on other sites More sharing options...
Darth Clouds Posted January 12, 2008 Report Share Posted January 12, 2008 (edited) Trooperbluecow said: Thanks for the ideas. From what I have read around here AP helmets can be thin in some places, like the place I had a problem. I think that I will try the epoxy and see if I can reinforce it. With the mic tips in place I don't think the crack will be noticeable and the epoxy should help with the strength. I tried strengthening that area with "abs goo", but it need some prior experience in using that stuff. If we use the wrong amount of acetone in the goo, bad news. It will also cause softening of the hovi tips area in the lid. I would recommend super glue because it is colourless, as compared to a two part epoxy. But be aware of the dust particles in the lid, if you happen to sand the dried super glue or epoxy. Some people are allegic to that type of dust. I will post some pictures over the weekend on my build------------ pertaining to my attempt in strengthening that area. Well, I have not found the time to consolidate them as yet but here is some of them piece meal. Edited February 12, 2021 by gmrhodes13 link not working, removed gmrhodes13 2021 Quote Link to comment Share on other sites More sharing options...
Scootch[TK] Posted April 14, 2008 Report Share Posted April 14, 2008 I've had several guys tell me super glue plus baking soda = big time bonding to plastic. Never tried this but if it works you could glue a piece of your trim scraps in the inside of the bucket to reinforce it. You could use ABS glue for that as well. Quote Link to comment Share on other sites More sharing options...
TN-TROOPER Posted October 4, 2008 Report Share Posted October 4, 2008 the best thing I have came up with to repair plastic cracks is fiberglass resin Quote Link to comment Share on other sites More sharing options...
rapstertee Posted October 12, 2008 Report Share Posted October 12, 2008 the best thing I have came up with to repair plastic cracks is fiberglass resin take a small square of t-shirt material and soak it with super glue. Then just spread it over the back of the cracked area. In about 5 minutes it will be rock solid. It takes minutes and is really easy to do. I used it - see my AP build - and Great results - but don't use a drill on it - use a pointy scalpel blade or exacto knife. Quote Link to comment Share on other sites More sharing options...
tatooine Posted November 5, 2008 Report Share Posted November 5, 2008 EA956 (Hysol product) resin matrix impregnated on a small square of fiberglass cloth. Your bucket would fall apart around that repair! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.