Search the Community

On that time scale you're going to struggle, local vendors aren't with us anymore to my knowledge. Best bet will be to get hunting for some appropriate black Chelsea boots and crack out the white leather paint. That said I'll have a word with the local armoury team, see if I can find a lead. The way they work is they do "runs". They next open on May 17th until 24th, and then close orders again. They then spend the next few weeks manufacturing everything on that run. This means they can benefit from economies of scale, on made to order products or having to hold a lot of expensive stock they might never sell.

Keep Trooping does monthly runs. You likely could not get one in a couple weeks. If it was about 6 weeks away, it would be no problem. You're looking for model 421 on the keeptrooping website. They're just white chelsea boots though. If you can find a set locally, you can paint with any leather paint.

Below is an amended Nightrooper/R1 CRL. Items known to not be on the costume, such as cod and posterior, have been committed. Please remember this is a work in progress and is not final. Required Costume Components The following costume components are present and appear as described below. General Construction Notes All costume elements are painted and weathered to match the specific visual references for this costume. At basic level, level 2 gold or gold colored leaf is not required. At basic level cracks can be painted on, but must be engraved to obtain EIB (Level 2). All Armor is constructed from a durable material such as Metal, Fiberglass, Resin, Sintra, HIPS, PVC, PLA, Vac-formed ABS, or similar. EVA foam & Similar materials are not appropriate. 3D printed components must have no visible print lines or joins. Armor is scaled proportionately to the wearer. Please Note: All damage must be 100% screen accurate if individual wishes to obtain EIB (Level 2) approval from Detachment. Helmet Helmet is based on the Rogue One/Anthology style stormtrooper helmet. The face plate is gold in color Vocoder (vertically ribbed chin detail) is painted black. Lenses are black or grey in color. Lenses sufficiently dark enough to obscure the costumer's eyes. There are two cheek tubes that extend from the ears. Two vent greeblies are present in the end of each cheek tube at the bottom front of the helmet. Trapezoids on dome and tears on the cheeks of helmets are grey. Rear traps and tears have vertical black lines. There are 2 red imperial cogs on the front dome of the helmet. The cogs are positioned symmetrically, one on each side. The cogs have light weathering. The cogs are rotated as per references. Light to medium weathering as per references. Cracking as per references. Cracks may be painted on surface in metallic gold paint. Gray and gold color patches as per references. Note: The helmet is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): Eye Lenses are domed in shape. Cracks are engraved into the surface. Ear screws must not have a visible slot mark and be flush to the ear. Any gap between the ears and helmet will only appear to be a seam, not any bigger. OPTIONAL Level three certification (if applicable): Face plate and gold patches are covered with gold colored leaf. Cracks are filled with gold colored leaf. Vocoder is tubular in nature with 7 vertical tubes. A visible gap must be present between the Vocoder and the helmet. The inside of each rear trap will be a raised area that is grey, with 13 engraved black vertical lines, hand painted lines like ANH are not permitted. The inside of each side trap will be a raised area that is grey. Neck Seal Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to conceal the entire neck. Under Suit Dark Burgundy, non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs. OPTIONAL Level two certification (if applicable): Where visible shall be fully ribbed with all horizontal ribbing on the arms, legs, and back. The centre of chest and back may be mesh as long as it is covered by armor. OPTIONAL Level three certification (if applicable): All ribbing on knees, arms, chest, and back must be proportion to official references. Where visible around the neck the under suit is black. Shoulder Straps They may be affixed with Velcro or adhesive. Light to medium weathering as per references. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): These shall be inserted behind the chest tabs and into slots of the backplate. Shoulder Armor One on each shoulder. The shoulders are considered effectively symmetrical; but are not interchangeable. Left shoulder must be gold colored. Right shoulder must have 1 gold colored area per references. Light to medium weathering as per references. Cracking as per references. Cracks may be painted on surface in metallic gold paint. OPTIONAL Level two certification (if applicable): Cracks are engraved into the surface. OPTIONAL Level three certification (if applicable): There is no swoop on the shoulder bell raised area. There is no elastic strap that wraps around the inside of the bicep. Gold sections are covered with gold colored leaf. Cracks are filled with gold colored leaf. Upper Arm Armor The front strip is bevelled and approximately ⅛" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. Light to medium weathering as per references. Cracking as per references. Cracks may be painted on surface in metallic gold paint. Left side is approximately 3/4 grey as per references. Right side has 1 grey area that wraps the part as per references. OPTIONAL Level two certification (if applicable): Cracks are engraved into the surface. OPTIONAL Level three certification (if applicable): Cover strips will cover both the front and back joints. Biceps are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cracks are filled with gold colored leaf. Forearm Armor The front strip is bevelled and approximately ⅛" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. Light to medium weathering as per references. Cracking as per references. Cracks may be painted on surface in metallic gold paint. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Forearms are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the top and bottom joints. Gold sections are covered with gold colored leaf. Cracks are filled with gold colored leaf. Hand Plates Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material. Light to medium weathering as per references. Cracking as per references. Cracks may be painted on surface in metallic gold paint. Left handplate is gold colored. OPTIONAL Level two certification (if applicable): Hand guards shall be made of plastic. Cracks are engraved into the surface. OPTIONAL Level three certification (if applicable): Hand guards should follow the correct RO shape, ANH hand guards are not acceptable. A small indent in the front of the hand plate shall be present. Cracks are filled with gold colored leaf. Left handplate is covered with gold colored leaf. Gloves Dark Burgundy, leather or leather-like, enclosed fingered, non-textured, (normal leather grain/texture/lines are acceptable) fitted style. No buckles, straps, or decorative stitching. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Chest Armor Chest plate overlaps the abdominal plate. Light to medium weathering as per references. Cracking as per references. Cracks may be painted on surface in metallic gold paint. Right side must have 1 gold colored area per references. OPTIONAL Level two certification (if applicable): Cracks are engraved into the surface. There are raised trapezoids at the top of the shoulder section beneath which the straps insert. The chest and back sides shall be connected by black extensions pieces. OPTIONAL Level three certification (if applicable): Top pectoral out lines swoop correctly outward. Gold sections are covered with gold colored leaf. Cracks are filled with gold colored leaf. Back Armor There are raised trapezoids at the top of the backplate section beneath which the shoulder straps insert. The backplate continues past these trapezoids towards the top of the shoulder Right side There is a black square shaped greeblie with a circular gold recess detail Left Side There is a rectangular raised section. There is a black colored rectangular frame. There is a gray section on the left. There are 2 raised vertical bars that are gold in color. Lower section There is a black square greeblie below the right greeblie. There is a small vertical rectangle to the right of the black square greeblie. There is a small rectangular greeblie with rounded ends below the right side black greeblie. Light to medium weathering as per references. Cracking as per references. Cracks may be painted on surface in metallic gold paint. There is a gold colored section along the bottom of the armor as per references. OPTIONAL Level two certification (if applicable): Cracks are engraved into the surface. Top of box wall has a trapezoidal indentation. OPTIONAL Level three certification (if applicable): Bottom of backplate is curved and extends past abdominal back cover plate. Gold sections are covered with gold colored leaf. Cracks are filled with gold colored leaf. Abdomen Armor The abdominal armor consists of a one-piece corset design with a vertical opening centered on the back. The back opening is covered by a rectangular cover plate that is worn under the back armor. There are 3 vertical ribs centered on the front of the abdomen and two (one left and one right) ribs further spaced to each side of the center. There are two (one left and one right) angled (approximately 70 degrees) ribs on each side of the abdominal armor. There are two (one left and one right) angled (approximately 70 degrees) recessed ribs on each side of the abdominal armor behind the raised angled ribs that are black Any side shims added are to be added to the white areas of the armor. The center front detail consists of a raised rectangular panel. On the right half of the panel, there is a vertical column of 4 buttons approximately ⁷⁄₁₆" (11mm) in diameter. The bottom button is blue while the other three are grey. On the left half of the panel, there is a vertical column of raised evenly spaced horizontal gear teeth with a recessed trapezoid at the top of the column. The rectangular inside bottom of the trapezoid is black. The left front detail consists of a raised rectangular panel with an angled top. There is a vertical column of 4 buttons approximately ⁷⁄₁₆" (11mm) in diameter. The right front detail consists of a primary raised rectangular panel with an additional secondary raised rectangular panel covering the top ⅓ of the primary panel. There is a column of three thin horizontal evenly spaced raised lines across the top ½ of the secondary panel. The abdominal armor is accurate in detail and proportion to official references. Light to medium weathering as per references. Cracking as per references. Cracks may be painted on surface in metalic gold paint. The armor is gold in color. OPTIONAL Level two certification (if applicable): Cracks are engraved into the surface. The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. OPTIONAL Level three certification (if applicable): The abdomen armour is covered with gold colored leaf. The abdomen armor has two horizontal recessed rectangles centered above the center front detail panel and on each side of the center rib. All 8 Button details are recessed and bordered with a thin edge, only the recessed portion is painted. The center front panel column of raised gear teeth has only 9 teeth. There is a recessed edge (approximately ⅛" 3mm wide) along all four sides around the face of the center front panel The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. There is a recessed edge (approximately ⅛" 3mm wide) along the sides and top around the face of the left front detail pane The abdominal armor back cover plate has two protruding tabs along the bottom that rest inside the back hard belt. Kama There is a red fabric waist band approx 2.5-3x the width of the belt. The top fabric band is level with the bottom of the 3rd button down on the abdomen. There are 2 padded fabric panels at the font, these panels are not rectangular and have a slight trapezoid shape. The front panels end approximately at the knee. There is a third padded front panel, rectangular in shape behind the front two, and approx 2/3rds their length. There are two trapezoidal quilted hip panels, these panels end mid thigh. The quilting forms a vertical diamond pattern. There are two rear padded panels THIS NEEDS CONFIRMATION FROM REFERENCE, could it be pleated? The panels are same length as the front panels. The panels do not wrap past the front of the hip. The panels over lap by approx 6" at the rear, left over right. All panels have a border and backing that matches the waist fabric. Kama is lightly weathered. Belt Is made from black leather, or leather like material. Sits in the middle of the fabric band of the Kama. Is approx XXmm wide MUST CONFIRM There is a front rectangular section approx XXm tall MUST CONFIRM and is rounded on the right side. There is a raised section on the left side which is pointed on the right end. A thinner top strip runs the length of the belt and over laps the front section, with a pointed ends, forming the detail on the front of the rectangular section. Is closed at the rear. There is a single popper shortly before the holster. Staps There are two straps approx XXmm wide MUST CONFIRM that loop down from the belt. Mount to a short strap at the rear that hangs vertically on each side, and is looped over the belt. There is a single belt loop to the left of the rectangular section, level with the strap. Holster Is made from black leather, or leather like material. Is worn on the right hip Hangs from a single wide loop. Has 2 black poppers just under the belt loop. Thigh Armor The thigh armor is mirrored for each leg and not interchangeable. The cover strips are beveled and approximately ⅛" thick that does not extend beyond the thigh and has a smaller cover strip layered thereon. The top edge of the thigh armor is unadorned, and the bottom edge has a raised detail that fallows the bottom edge contour. Light to medium weathering as per references Cracking as per references. Cracks may be painted on surface in metalic gold paint. Right Side The thigh is predominantly gray There is a gold colored section at the bottom of the thigh There is a white colored section at the bottom of the thigh The small ammo belt consists of 5 evenly spaced rectangle ammunition boxes and is installed on the bottom of the right thigh, there are no visible screws or rivets. The ammo belt it gold in color Left Side White in color There is a gold colored section on the outside of the thigh at the bottom. OPTIONAL Level two certification (if applicable): Cracks are engraved into the surface. Thighs are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the front and rear joints. OPTIONAL Level three certification (if applicable): The bottom outside edges of the small ammunition belt are angled at approximately 45 degrees. Thigh armor is suspended by a black strap approximately 1" 25mm in width with a plastic side release buckle that is covered by black webbing or elastic that runs down the side seam of the leg. Gold sections are covered with gold colored leaf. Cracks are filled with gold colored leaf. Lower Leg Armor The greaves are mirrored for each leg and are not interchangeable. The top edge of the greaves has a raised detail that fallows the top edge contour. The bottom edge of the greaves flairs out to cover the top of the ankle and boots. The cover strips are beveled and approximately ⅛" thick that does not extend beyond the greave and has a smaller cover strip layered thereon. Greaves are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the front and rear joints. The trapezoid knee plate (sniper knee plate) is affixed to the top of the left greave and there are no visible screws or rivets. Sniper knee plate must be aligned with the vertical cover strip and the top raised edge detail on the greave and is accurate in detail and proportion to official reference. Light to medium weathering as per references. Cracking as per references. Cracks may be painted on surface in metallic gold paint. OPTIONAL Level two certification (if applicable): Cracks are engraved into the surface. The sniper knee plate has raised detail that fallows the top edge contour. The sniper knee plate has 3 trapezoidal lugs on each side and 2 on the center bottom edge (totalling 8) of the knee plate. OPTIONAL Level three certification (if applicable): Gold sections are covered with gold colored leaf. Cracks are filled with gold colored leaf. Boots Boots are above ankle height and the same style as the First Order TK. Chelsea type boots in the style of OT TK are not acceptable. Boots are all white and made of leather or leather-like material Flat black soles without a heel. Patent leather or high gloss is not permitted. Light to medium weathering as per references OPTIONAL Level two certification (if applicable): There is no seam present on the front of the boot. The wearer's inner side of the boots have zippers and no side elastic. OPTIONAL Level three certification (if applicable): Optional Accessories Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use. Captain Enoch SE-14 Blaster The blaster has an extended cone shaped barrel. There are 3 gold colored rings on the blaster 1 on the extended barrel 1 at the start of the barrel 1 at the rear of the blaster There is a narrow scope that runs approximately from the rear of the blaster to the top front sight. The scope is flared out at the rear Hand grips are white in color.

Boots. This is the only other point where I hope basic requirements for the costume are also changed (the first point being my mention of basic requirements for tube stripes above). The boots are really difficult to find in general. The long-running tale across the Legacy build threads has been difficulty in sourcing boots that fit the CRL. Folks in 2018 were fortunate to have the run of boots from Imperial Boots (Keep Trooping), and some earlier Legacies used Gio's boots (but it seems some have had trouble lately getting approved with Gio's boots). Those who have built this costume certainly don't need to be reminded of the difficulty of getting the boots, because we have lived it, but I say this all here to document how difficult sourcing boots has been so those not familiar with the costume understand the difficulties. I argue a change should be made to basic requirements to reflect the difficulty of sourcing boots, not just when it comes to L2 and L3. This brings me to a point I read in a different thread in reference to the accuracy of the boots for Version A. The boots on the Jes Gistang statue don't have that tall of a heel (unlike what is currently noted in the CRL). Here's the thread with that discussion: Here's a photo of the boots on the statue (more photos are in the thread linked above): The statue heel isn't all that tall. There is still a noticable heel, but it is much shorter than currently portrayed in the CRL. As I mentioned above, this is the only other place where I think a change in the basic requirements is warranted (and I argue this change would be more important than the one about tube stripes, if there could only be one change). Perhaps the CRL could note Version A could have either the tall or short heel. Keeping the tall heel on the CRL would accommodate those who already wear the costume with tall heel boots, and also including the short heel would allow for greater options in sourcing boots for basic approval. The L2 and L3 requirements could indicate only a short heel. Additionally, to reflect the difficulty of sourcing boots in line with the CRL, perhaps a note could be added to the section about boots to inform GMLs that sourcing proper boots is really difficult and the availability of suitable boots needs to also be taken into account, especially because of variation in sourcing and supply chains in different countries. This would certainly help as a common boot that can be found, and can be modified to include the needed strip from toe to tongue (that is clearly shown in the photo of the statue, as well as currently required in the CRL), tends to be the Chelsea-type boot, commonly with a lug sole and elastic on the sides. After gluing on the strip from toe to tongue, the only sticking point tends to be the elastic on the sides (and occasionally the sole). Some GMLs have allowed the elastic, while others have not (or have required the elastic be covered). I think clarifying language on the difficulty of sourcing boots without elastic sides may help with consitency across garrisons. To review the boots, allowing a shorter heel in addition to the tall heel for basic approval (for Version A of the costume), as well as language clarifying the difficulty of sourcing boots that look like the photos in the CRL, would help address the difficulty many have had with completing the Legacy Fem costume. As far as L2 and L3, perhaps the short heel should be called for as a requirement.

The goal is to get this CRL complete as it's never been done before. I've asked Ingrid Moon (LadyInWhite) and Misty Melillo to lead this. Along with Teresa, Jana, Molly and several others, this is what they have so far. Yes, this is the TFA as the base and I'll make changes based on what they have posted in their GoogleDoc as updates, but wanted to get the base post started. NOTES: 1. This first post will always be the master list. Any agreed upon changes will be reflected here. 2. I will cite any change, e.g. [TFAL2] as something that is copied from the TFA L2, or [Ingrid] as an Ingrid change. 3. Goal is to have this 100% complete by the end of the year. Alrighty, so, let's get the party started. // Helmet *The helmet is mirror reflective and shall not be weathered. *Lenses are smoky brown or gray in color. They may be bubble in shape or flat and must be sufficiently dark enough to obscure the costumer's eyes. *The frown is solid black and covered in black hexagonal mesh that extends to the tears. *There are three slight grooves that circumvents the helmet above the brow, which is the same color as the helmet. *There is a slight groove that circumvents the helmet along the bottom and over the chin. *The bottom of the helmet flares slightly outward and is horizontal and flat on the bottom. *A “Mohawk”-like ridge is raised along the center of the helmet from the brow to the bottom back. *Parallel to either side of the raised ridge are three slight grooves; the third groove may cut back toward the trap. L2 *Grooves in helmet are not black or otherwise colored in. Neck Seal * Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to conceal the entire neck. L2 *Neckseal has a bib on front and back. *Neckseal shall have 11 ribs. Chest Armor *Chest is mirror reflective and shall not be weathered. *The chest plate overlaps the abdominal plate. *The “cut-out” in the center-top of the chest plate is recessed and black on the side and upward facing edges. *A small clasp greeblie shall be present on each side of the chest, just inside a small indented area the size of the greeblie. *There is a groove running vertical on each lateral side of the chest that angles toward the center. *Six recessed black ovals are on the wearer's right side, left of the greeblie. L3 *Channel on sides of chest should show clear separation. Back/Yoke *Yoke is mirror reflective and shall not be weathered. *The back plate contains a "O II" design. *The back/yoke is one seamless piece. *The yoke portion extends over the wearer's shoulders and curves under the armpits. Thermal Detonator* The thermal detonator mounting plate is mirror reflective, unweathered, and sits under the back plate and rests above the belt.* The control panel is black.* The right-hand recessed end cape is black.* The left-hand end cap extends from the detonator assembly and is black all around the cylinder as well as the end surface. A silver stripe is present around the end of the cylinder that extends slightly onto the circular surface.* There should be no visible seams. L2 *Small section of black around the base of the left extended end cap shall be present. Shoulder Gaskets *Gaskets shall be rubber or a shiny black material with ridges. *The shoulder gaskets must cover all exposed areas under the shoulder bell, between the bicep and chest, and between bicep and back. L3 *Gaskets shall be made of rubber. Fabric gaskets are not acceptable. Shoulder Bells *One on each shoulder. *Bells are mirror reflective and shall not be weathered. *The shoulders are considered effectively symmetrical. They may be worn interchangeably on the left and right shoulders. *Shoulders have small round extension at the top under the bell itself that butts up against the yoke. Biceps *Biceps are mirror reflective and shall not be weathered. *Biceps have only one seam on the side that faces forward. *A clip greeblie is present low and across the seam. *Two black ovals are present on the outward facing side of the bicep. L3 *Ridges in bicep must be present (small detailed section). Elbow Gaskets *Gaskets shall be rubber or a shiny black material with ridges. *The elbow gaskets must cover all exposed areas between the bicep and forearm. L3 *Gaskets shall be made of rubber. Fabric gaskets are not acceptable. Forearms *Forearms are mirror reflective and shall not be weathered. *Forearms shall have ridged rail, similar to a picatinny, embedded on the inside of the forearm. *Forearms shall have a box on the bottom the wrist end, roughly covering 1/3rd of the embedded rail. *Each forearm shall have two 'clasp greeblies' on the outward facing surface, near the wrist. *Detail box includes black rectangle on small edge perpendicular and closest to wrist. Gloves/fingers *Hand armor is mirror reflective and shall not be weathered. *Gloves are black. *Gloves extend underneath the forearm. *Hand plates are rigid square boxes and the hand plates are mounted securely over the back of the glove. *A trapezoidal wrist plate is mounted securely between the hand plate and the forearm, contoured to match the hand plate.*Finger armor is three rigid pieces per finger, proportionate in size to the fingers, with the fingertips ending in small, contoured trapezoids. L2 *There shall be a scribed border on the top, approximately 1/2" from the edge all the way around each plate. L3 *Glove inner palm must have black stitching. Abdomen Section *Abdomen section is mirror reflective and shall not be weathered. *The abdomen section must wrap around the wearer's body. *The abdomen has 7 boxes attached that matches the order and placement shown. *The large box has a small black recessed square to on the lower left of the wearer. *The second box to the right of the wearer has a small black recessed rectangle near the top. Codpiece *The codpiece is mirror reflective and shall not be weathered. *The codpiece sits below the abdomen and under the belt. *The codpiece is relatively flat, triangular, and contains two rectangular indentations, one on either side of the center. Posterior armor *Posterior armor is mirror reflective and shall not be weathered. *The posterior armor sits below the abdomen and under the belt. *The top portion of the part is hidden by the belt and used to connect the plate to the abdomen armor. Belt *The belt is ribbed and made from a rubber or a rubber like material. *The belt boxes consist of 2 horizontal boxes, 2 small vertical boxes, and 2 medium vertical boxes. There are no soft pouches with covers on the belt. *The two horizontal boxes worn on the front, one on each side of the center. They are mirror reflective on the outside/front half and black on the inside/back half. *Next to each horizontal box is a small vertical box, then the medium vertical box. The two sides of the belt are symmetrical. Undersuit *An undergarment must be worn such that the space between the thighs and the belt shows a black material. The black material may be shiny or matte. *The reference photo shows the type used on screen but is not required for basic approval. L3 *The shorts area of the undersuit should be shiny. Thighs *Thighs are mirror reflective and shall not be weathered. *There are seams on the inside and outside of each thigh. *A clip greeblie is present high and across the outside seams of each thigh. *The wearer's right thigh includes a base for a weapon holster. Holster does not need to be functional. Knee Gaskets *Gaskets shall be rubber or a shiny black material with ridges. *The knee gaskets must cover all exposed areas between the thigh and shin. L3 *Gaskets shall be made of rubber. Fabric gaskets are not acceptable. Knee Plates *The knee plates are mirror reflective and shall not be weathered. *The knee plates mirror each other and are placed evenly between the thigh and the shin. *Convex edge of knee plate faces downward. Shins *Shins are mirror reflective and shall not be weathered. *There are seams on the inside and outside of the shins, with the opening on the inside. *A clip greeblie is present high and across the outside seams of each shin. *The wearer's left outside shin includes two vertical thin boxes that are seamless. L2 *There are pills at the bottom of the shins just above the spats. Boots *Boots are black suede, leather, or leather-like, absent of laces, with no pronounced heel. They may be Chelsea (TK) or First Order (TK) style boots. L3 *Boots must have a small heel, unlike regular FO style boots. Shin Armor *Shin and foot armor are mirror reflective and shall not be weathered. * The foot armor consists of four pieces: ** A toe armor plate that is rigid and has a contoured curve that covers the front top of the boot ** A heel cover that is a semi-circular piece that affixes to the rear heel of the boot ** Instep armor which is a rounded edged rectangle that sits above the toe armor and rests against the shin piece ** A circular spat piece that has a greeblie on the outside edge of each spat, and a matching contour indent in the front that aligns with the shin armor. Cape *The cape is a black cotton canvas or rubberized canvas that crosses the chest diagonally from the right shoulder to the left elbow area. *There is a red stripe painted down the entire left seam of the cape. The stripe and seam are approximately 1.25” - 1.5” wide. *There is a seam down The right side of the cape approximately 1” - 1.25” wide. *The cape attaches at the right shoulder with a semi hidden closure and there is a black leather or leather like strap approximately 1.5” x 14” that drapes over the right shoulder onto the costumer’s back. *There are 4 pockets on the back left side of the cape starting approximately in the shoulder blade area in a 1, 2, and 1 pattern. The top and bottom pockets are approximately 4.5” x 9” and the 2 middle pockets are approximately 5.5” x 11.5”. The bottom pocket has a black leather or leather like strap approximately 1.5” x 14” attached horizontally to the bottom left corner. *There are 2 black leather or leather like straps attached horizontally to the left seam, behind the red stripe approximately located around the left hand area. The top strap is located about 1” above the bottom strap. The top strap is approximately 1.5” x 16” and the bottom strap is approximately 1.5” x 14”. *The back of the cape should be long enough to touch the ground but may vary in length +/- a few inches. The back of the cape rises diagonally from the left foot area to the right hand/knee area. There is a hem along the entire bottom of the cape. L2 *The cape is made of cotton canvas and consists of 4 panels. *The cape is coated with a binder giving it a slight sheen. *The right shoulder connection is permanent or semi-permanent and allows the right side of the cape to rotate. This creates waves and bunching across the back of the cape. *The cape has bunching at the left shoulder area. ACCESSORIES Captain Phasma Blaster Rifle *Based on a replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster. *Similar to standard First Order Stormtrooper Blaster with extended stock attached. *Details are mirror reflective and shall not be weathered. L3 *Working lights and working front torch are required. *Front handle must be movable. Captain Phasma SE-44C *Based on a replica Glock 19 repeating pistol, scratch-built, or a modified commercial Stormtrooper toy. *Details to be painted black, white and mirror reflective per reference photos, and not be weathered. Quicksilver baton (spear) *The spear is mirror reflective in color. *The spear is of varying length (it telescopes in the film) and has a cutout section at the 2 foot and 5 foot height marks that is comprised of a small circle, a small oval, and a larger elongated oval. *Length is proportional to costumer and extends approximately 12 inches above the costumer's height.

Stirred up some conversation over on the Facebook already, but figured this deserved a thread over here too. A screen matched Hero Stormtrooper costume from Star Wars - A New Hope (1977) has recently come up for auction, and the sales post contains some excellent photos of 1 of only 3 known surviving Hero suits/helmets out of the 6 made for the film. It is pretty much complete and in absolutely gorgeous condition. Enjoy. Per the Auction's description: Original Screen Matched Complete Hero Imperial Stormtrooper Costume from Star Wars: Episode IV - A New Hope (TCF, 1977). Vintage screen matched original Hero Stormtrooper costume constructed of vacuum-formed ABS plastic components. This complete hero style helmet features a one-piece green bubble-shaped lens, original elastic chin strap, original mic-tips, original rubber brow and neck trims, and hand-painted details. Complete armor components include torso assembly (chest, back, abdomen, kidney, butt, and 2 ribbed shoulder connectors), left and right shoulder bells, left and right arm assemblies (biceps and forearm armor), left and right thigh armor, left and right shin armor, belt assembly (layered-stitched canvas fabric belt, ribbed front plate, 2 ammo drop boxes, and distressed leather holster), thermal detonator canister, and white brush-painted chelsea boots. All armor components are assembled and held together with original metal hardware and elastic strapping. Also included is it's original off-the-shelf thin black leather belt which was used to attach the thigh armor to the actor. This belt is the only known example in existence to survive the entire production. Black spandex bodysuit added for display. There were only 6 hero style helmets made for the film, making this helmet only 1 of 3 hero helmets known to still currently exist. After filming was completed in England, this being 1 of 2 of the best condition remaining costumes were hand selected and sent back to the United States for additional pick-up shots such as the 'space trooper' standing at the entrance of Death Star Docking Bay 327 as the Millennium Falcon is drawn in by the tractor beam. This particular Stormtrooper is prominently featured throughout the film and can be screen matched sharing scenes with both Princess Leia as well as Darth Vader. It was also featured in the Donny and Marie Star Wars Special (1977), the Star Wars Holiday Special (1978), and the 50th Academy Awards (1978). This incredibly rare and special Stormtrooper costume rich with history is the most complete and best condition example known to exist from the first original Star Wars film (1977). Exhibits age, production wear and handling, discoloration, scuffing, small cracks, crazing, and minor paint loss. Comes with a COA from Heritage Auctions. Suit Gallery Helmet Details It has been confirmed to match the suit seen throughout the film, as shown: Link to Auction HERE

Below is an amended R1 TK CRL, I have ommitted items like the batton and Pauldron and some blasters that were not seen in use in the Ahsoka series . Required Costume Components The following costume components are present and appear as described below. Helmet Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray. Rear traps and tears have engraved vertical black lines. Lenses can be flat material, green in color, sufficiently dark enough to obscure the costumer's eyes. The “ear” bars are gray or painted gray, with the largest bar oval cutout painted black. Frown is painted gray and does not leave the teeth area. The space between the 8 teeth is hollow and backed with Black or Dark grey wire screen mesh. Tube stripes are medium blue, numbering 12 per side. The stipes are straight, not curved like ANH. Vocoder (vertically ribbed chin detail) is painted black. Aerators/Hovi mix tips (cylinders on either side of the vocoder) have a black exterior and silver in color screen mesh. Tears and traps may not be hand-painted. Tube stripes are recessed, and the recessed section painted blue or backed by blue mesh. Note: The helmet is accurate in detail and proportion to official references. Many commercially available helmets or those considered disproportionate in size or shape are ineligible. The Black Series helmet is approvable if modified to meet the level 1 CRLs. Light to medium weathering as per reference images. Cracks may be painted on surface in metalic gold paint. OPTIONAL Level two certification (if applicable): Lenses have a very slight curve and are convex in style. Flat lenses and ANH style bubble lenses are not permissible. Rank bar area on ear must be of the correct RO style and pattern, no ANH style ear bumps allowed. Head opening has black trim running all along the edge. Brow trim should be positioned ¼" above the eyes. Ear screws must not have a visible slot mark and be flush to the ear. Any gap between the ears and helmet will only appear to be a seam, not any bigger. Correct 'Hovi mic' aerator tips. Chin section has a well defined seam from the angles of the mouth. Light to medium weathering as per references Cracks must be dremmelled or engraved into helmet. Cracks may be painted in metalic gold paint OPTIONAL Level three certification (if applicable): The Tube stripes are completely hollowed out with a blue section underneath. Vocoder is tubular in nature with 7 vertical tubes. A visible gap must be present between the Vocoder and the helmet. The inside of each tear will be a raised area that is grey, with 8 engraved black lines, hand painted lines like ANH are not permitted. The frown shall be recessed to the proper depth, unlike standard ANH. The inside of each rear trap will be a raised area that is grey, with 13 engraved black vertical lines, hand painted lines like ANH are not permitted. The inside of each side trap will be a raised area that is grey. There is a small bump in the right eye socket (when worn) under the lens as an intended flaw to pay tribute to the original trilogy designers. Green LED that can be switched on and off representing both living and the reserected Night trooper shall be fitted behind the lenses. TK anh stunt neckseal.jpeg Neck Seal Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to conceal the entire neck. Cracks must be dremmelled or engraved into helmet. Cracks must be gold leaf, gold paint is not permitted. Under Suit Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs. OPTIONAL Level two certification (if applicable): Top, where visible shall be fully ribbed with all horizontal ribbing on the arms, chest, and back. The centre of chest and back may be mesh as long as it is covered by armor. Pants shall be black non-textured material and have horizontal ribbing at the knees only. Knee gaskets are allowed as long as they correctly match top ribbing material, spacing and color. The hip section shall not have ribs. OPTIONAL Level three certification (if applicable): All ribbing on knees, arms, chest, and back must be stitched between each rib in detail and proportion to official references. The armpit area shall have the correct hexagonal mesh detail Shoulder Straps They may be affixed with Velcro or adhesive. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): These shall be inserted behind the chest tabs and into slots of the backplate. Shoulder Armor One on each shoulder. The shoulders are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders and may have a black elastic strap that wraps around the inside of the bicep. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): There is no swoop on the shoulder bell raised area. There is no elastic strap that wraps around the inside of the bicep. Weathering details, Gold and gray adorntments etc to be added. Upper Arm Armor Both biceps are symmetrical and interchangeable. The front strip is bevelled and approximately ⅛" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Cover strips will cover both the front and back joints. Biceps are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Weathering details, Gold and gray adorntments etc to be added. Forearm Armor The front strip is bevelled and approximately ⅛" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Forearms are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the top and bottom joints. Weathering details, Gold and gray adorntments etc to be added. Hand Plates Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): Hand guards shall be made of plastic. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): Hand guards should follow the correct RO shape, ANH hand guards are not acceptable. A small indent in the front of the hand plate shall be present. Weathering details, Gold and gray adorntments etc to be added. Gloves Black in color, made of Nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured. Rubber ANH style gloves are not permitted. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): The base material of the gloves will be a black synthetic material similar to Lycra, Spandex, Elastane, or Nylon. Palms of gloves shall be shiny black fabric or leather or leather-like material. On the index finger shall be a stitched piece of fabric made from the same material as the hand's underside that while stitched to the finger has one cutout towards the end of the finger that reveals the netted material underneath. Gloves shall have the correct leather pattern along the fingers/palm. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): Chest Armor Chest plate overlaps the abdominal plate Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): There are raised trapezoids at the top of the shoulder section beneath which the straps insert. The chest and back sides shall be connected by black extensions pieces. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): Top pectoral out lines swoop correctly outward. Bottom of ribcage flares correctly outward. Weathering details, Gold and gray adorntments etc to be added. Back Armor Back plate contains an "O II" design. There are raised trapezoids at the top of the backplate section beneath which the shoulder straps insert. The backplate continues past these trapezoids towards the top of the shoulder Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): Top of box wall has a trapezoidal indentation. There is a roughly 8mm circular indent near the right top corner of the backplate. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): Bottom of backplate is curved and extends past abdominal back cover plate. The O cog shall have 16 spines. The 11 bars have 5 horizontal evenly spaced raised bars on the bottom of the face. There is a rectangular tab protruding from the bottom of each of the two raised trapezoids at the top of the backplate. Weathering details, Gold and gray adorntments etc to be added. Abdomen Armor The abdominal armor consists of a one-piece corset design with a vertical opening centered on the back. The back opening is covered by a rectangular cover plate that is worn under the back armor. There are 3 vertical ribs centered on the front of the abdomen and two (one left and one right) ribs further spaced to each side of the center. There are two (one left and one right) angled (approximately 70 degrees) ribs on each side of the abdominal armor. There are two (one left and one right) angled (approximately 70 degrees) recessed ribs on each side of the abdominal armor behind the raised angled ribs that are black Any side shims added are to be added to the white areas of the armor. The center front detail consists of a raised rectangular panel. On the right half of the panel, there is a vertical column of 4 buttons approximately ⁷⁄₁₆" (11mm) in diameter. The bottom button is blue while the other three are grey. On the left half of the panel, there is a vertical column of raised evenly spaced horizontal gear teeth with a recessed trapezoid at the top of the column. The rectangular inside bottom of the trapezoid is black. The left front detail consists of a raised rectangular panel with an angled top. There is a vertical column of 4 buttons approximately ⁷⁄₁₆" (11mm) in diameter. The bottom button is blue while the other three are grey. The right front detail consists of a primary raised rectangular panel with an additional secondary raised rectangular panel covering the top ⅓ of the primary panel. There is a column of three thin horizontal evenly spaced raised lines across the top ½ of the secondary panel. The abdominal armor is accurate in detail and proportion to official references. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): The cod armor is separate from the abdominal armor. The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): The abdomen armor has two horizontal recessed rectangles centered above the center front detail panel and on each side of the center rib. All 8 Button details are recessed and bordered with a thin edge, only the recessed portion is painted. The center front panel column of raised gear teeth has only 9 teeth. There is a recessed edge (approximately ⅛" 3mm wide) along all four sides around the face of the center front panel The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. There is a recessed edge (approximately ⅛" 3mm wide) along the sides and top around the face of the left front detail pane The abdominal armor back cover plate has two protruding tabs along the bottom that rest inside the back hard belt. Weathering details, Gold and gray adorntments etc to be added. Cod Armor The cod armor consists of a body shape formed triangular plate with a raised center rib and raised lower portion and is accurate in detail and proportion to official references. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): The cod shall be a separate piece from the abdominal plate. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): Kidney Armor The kidney armor is separated in the back and covered by a rectangular plate. The rectangular plate is separate from the posterior armor. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Posterior Armor The posterior armor shall be a separate piece from the abdominal armor Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Belt The Ammunition belt consists of a hard belt made of the same or similar material as the armor in two separate parts front and back (with overlap). The back belt overlaps the front belt on the sides. There are 6 ammunition boxes mounted to the belt. There are 2 (one left and one right) drop boxes suspended by black webbing approximately 2" (50mm) wide. Drop boxes must be accurate in detail and proportion to official references. The ammunition belt is accurate in detail and proportion to official references. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): The only detail visible on the front belt is the mounted ammunition boxes unlike the squares present on ANH belts. The top edge of the front belt has protruding teeth that nest inside gaps between the ribs and detail panels of the abdominal armor. The two center ammunition boxes are thinner than the other mounted ammunition boxes. The second and fifth mounted ammunition boxes are slightly wider than the two center ammunition boxes. The two outermost ammunition boxes are almost square. The two drop boxes are rectangular and as wide as the mounted square boxes. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): The ammo boxes across the front are all made separately from the main belt and are secured to it The two drop boxes hang no more than 1" 25mm below the front belt and the black strap is visible. The second and fifth mounted ammunition boxes have trapezoid detail on the top of each ammunition box. The front belt protrudes past all mounted ammunition boxes above and below by approximately ⅛"–¼" 3–6mm. All ammunition boxes have slightly beveled edges on the face of each box. Weathering details, Gold and gray adorntments etc to be added. Thermal Detonator The thermal detonator consists of a grey tube approximately 3" 76mm in diameter and 8" 203mm long approximately. There are two white endcaps and a white control panel. The white control panel has a horizontal row of white rectangles along the bottom of the control panel and a grey “D” shaped recessed on the left side of the horizontal row. There is an oval greeble that protrudes from the control near the top right side. The thermal detonator is mounted to the rear hard belt and there are no visible screws or clips and is accurate in detail and proportion to official references. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): The thermal detonator mount should be fully enclosed with solid walls on all four sides. The center of both end caps is gray. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): The control panel bottom detail is a raised panel with 7 raised rectangles, all are evenly spaced except the right most rectangle. There is a panel line approximately ¼" 6mm from the edge around the control panel. There is a panel line approximately ⅛" 3mm from the edge of each endcap. The inside edge of both endcaps is beveled. The oval greeble consists of an oval tube protrusion with the top edge slightly extending past the tube wall thickness and is visually similar to the Deathtrooper chin greeble. Weathering details, Gold and gray adorntments etc to be added. Thigh Armor The thigh armor is mirrored for each leg and not interchangeable. The cover strips are beveled and approximately ⅛" thick that does not extend beyond the thigh and has a smaller cover strip layered thereon. The top edge of the thigh armor is unadorned, and the bottom edge has a raised detail that fallows the bottom edge contour. The small ammo belt consists of 5 evenly spaced rectangle ammunition boxes and is installed on the bottom of the right thigh, there are no visible screws or rivets. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): Thighs are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the front and rear joints. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): The bottom outside edges of the small ammunition belt are angled at approximately 45 degrees. Thigh armor is suspended by a black strap approximately 1" 25mm in width with a plastic side release buckle that is covered by black webbing or elastic that runs down the side seam of the leg. Weathering details, Gold and gray adorntments etc to be added. Lower Leg Armor The greaves are mirrored for each leg and are not interchangeable. The top edge of the greaves has a raised detail that fallows the top edge contour. The bottom edge of the greaves flairs out to cover the top of the ankle and boots. The cover strips are beveled and approximately ⅛" thick that does not extend beyond the greave and has a smaller cover strip layered thereon. Greaves are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the front and rear joints. The trapezoid knee plate (sniper knee plate) is affixed to the top of the left greave and there are no visible screws or rivets. Sniper knee plate must be aligned with the vertical cover strip and the top raised edge detail on the greave and is accurate in detail and proportion to official reference. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): The sniper knee plate has raised detail that fallows the top edge contour. The sniper knee plate has 3 trapezoidal lugs on each side and 2 on the center bottom edge (totalling 8) of the knee plate. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): Boots Boots are above ankle height and the same style as the First Order TK. Chelsea type boots in the style of OT TK are not acceptable. Boots are all white and made of leather or leather-like material Flat black soles without a heel. Patent leather or high gloss is not permitted. Light to medium weathering as per references Cracks may be painted on surface in metalic gold paint. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level two certification (if applicable): There is no seam present on the front of the boot. The wearer's inner side of the boots have zippers and no side elastic. Weathering details, Gold and gray adorntments etc to be added. OPTIONAL Level three certification (if applicable): Optional Accessories Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use. E-11 Blaster Manufactured by BlasTech Industries, the E-11 is standard-issue for many Imperial troops. Light, compact yet powerful, the E-11 blaster is always in high demand throughout the galaxy. "Note, the E-11 holster as seen in the Original Trilogy movies is not an authorized accessory for rogue One armor". Based on a real or replica Sterling Airsoft Gun, Sterling Sub-Machine Gun, scratch-built, or a modified commercial toy Stormtrooper blaster. A small flashlight can be mounted on the right side of the blaster centred over the T-Tracks. OPTIONAL Level two certification (if applicable): Blaster shall be based on a real or replica S&T Sterling L2A1 AEG Airsoft Gun. (Folding Stock does not need to function) D-Ring shall be present on the rear end cap. Scope shall be a real or replica M.H.R. (Minneapolis Honeywell Regulator Co.) M38 Telescope. 1943 model is preferred. Counter shall be a real or replica Hengstler 400 Series counter. Eagle logo is preferred. Power Cylinders shall be mounted on top of the magazine well. R1 style power cylinders are preferred over ANH style. 6 rows of T-Tracks cover the Sterling receiver holes except for the lower left row with the bayonet lug. Flashlight if fitted shall be a real or replica Element M300A Mini Scout Light. 3D printed blasters can not contain visible print lines and must be sanded smooth for a more realistic appearance. OPTIONAL Level three certification (if applicable): Scope shall be a real or replica 1943 M.H.R. Co. M38 Telescope, 1942 model is not allowed. Counter shall be a real or replica Hengstler 400 Series counter with Small eagle logo. Large eagle logo is not allowed. Power Cylinders shall be R1 style, ANH style is not allowed.

First full kit-up today. Glad I did this before I was going to take submission pics. I have a little ways to go anyway. Things to note here: 1. My magnetic chest clasps are not in the right place. The downside of trying to do this without actually seeing it on my own body. Looks like wearing it, my torso stretches the yoke a little wide, especially with the gaskets on. So, they need to move in and maybe down a little. I've considered velcro as that might be easier to adjust. I've just had a bear of a time getting the sides of the chest fastened correctly to the yoke. Having an assistant today helped a lot, but was even still a challenge. 2. I know, my helmet is TFA and my kit/cod is TLJ. I have both helmets, but this one was closer to me. 3. Boots arrive this week!! The last piece of the puzzle. Using my first hand-painted chelsea boots for this. The spats at least hide the fact they don't go up high enough. My ankles sure know the secret though. Pinchy. 4. The helmet is a WIP. I removed the hardhat liner for now and substituted a piece of standard foam. Doesn't fit at all yet so it's a little bobbly. I am going to line it like the premium DN helmet (separate thread eventually). My fave pose

If you wish to you could also help with the CRL text, ROTK copied below, adjust to suit the Night Troopers, copy/paste from below then edit, strike through what needs removing and add in green for new text. If aiming to be the CRL model you would also need to provide all CRL images required, I would suggest using a contrasting background, makes photo editing a little easier. Required Costume Components The following costume components are present and appear as described below. Helmet Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray. Rear traps and tears have engraved vertical black lines. Lenses can be flat material, green in color, sufficiently dark enough to obscure the costumer's eyes. The “ear” bars are gray or painted gray, with the largest bar oval cutout painted black. Frown is painted gray and does not leave the teeth area. The space between the 8 teeth is hollow and backed with Black or Dark grey wire screen mesh. Tube stripes are medium blue, numbering 12 per side. The stipes are straight, not curved like ANH. Vocoder (vertically ribbed chin detail) is painted black. Aerators/Hovi mix tips (cylinders on either side of the vocoder) have a black exterior and silver in color screen mesh. Tears and traps may not be hand-painted. Tube stripes are recessed, and the recessed section painted blue or backed by blue mesh. Note: The helmet is accurate in detail and proportion to official references. Many commercially available helmets or those considered disproportionate in size or shape are ineligible. The Black Series helmet is approvable if modified to meet the level 1 CRLs. OPTIONAL Level two certification (if applicable): Lenses have a very slight curve and are convex in style. Flat lenses and ANH style bubble lenses are not permissible. Rank bar area on ear must be of the correct RO style and pattern, no ANH style ear bumps allowed. Head opening has black trim running all along the edge. Brow trim should be positioned ¼" above the eyes. Ear screws must not have a visible slot mark and be flush to the ear. Any gap between the ears and helmet will only appear to be a seam, not any bigger. Correct 'Hovi mic' aerator tips. Chin section has a well defined seam from the angles of the mouth. OPTIONAL Level three certification (if applicable): The Tube stripes are completely hollowed out with a blue section underneath. Vocoder is tubular in nature with 7 vertical tubes. A visible gap must be present between the Vocoder and the helmet. The inside of each tear will be a raised area that is grey, with 8 engraved black lines, hand painted lines like ANH are not permitted. The frown shall be recessed to the proper depth, unlike standard ANH. The inside of each rear trap will be a raised area that is grey, with 13 engraved black vertical lines, hand painted lines like ANH are not permitted. The inside of each side trap will be a raised area that is grey. There is a small bump in the right eye socket (when worn) under the lens as an intended flaw to pay tribute to the original trilogy designers. TK anh stunt neckseal.jpeg Neck Seal Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to conceal the entire neck. Under Suit Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs. OPTIONAL Level two certification (if applicable): Top, where visible shall be fully ribbed with all horizontal ribbing on the arms, chest, and back. The centre of chest and back may be mesh as long as it is covered by armor. Pants shall be black non-textured material and have horizontal ribbing at the knees only. Knee gaskets are allowed as long as they correctly match top ribbing material, spacing and color. The hip section shall not have ribs. OPTIONAL Level three certification (if applicable): All ribbing on knees, arms, chest, and back must be stitched between each rib in detail and proportion to official references. The armpit area shall have the correct hexagonal mesh detail Shoulder Straps They may be affixed with Velcro or adhesive. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): These shall be inserted behind the chest tabs and into slots of the backplate. Shoulder Armor One on each shoulder. The shoulders are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders and may have a black elastic strap that wraps around the inside of the bicep. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): There is no swoop on the shoulder bell raised area. There is no elastic strap that wraps around the inside of the bicep. Upper Arm Armor Both biceps are symmetrical and interchangeable. The front strip is bevelled and approximately ⅛" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Cover strips will cover both the front and back joints. Biceps are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Forearm Armor The front strip is bevelled and approximately ⅛" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Forearms are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the top and bottom joints. Hand Plates Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material. OPTIONAL Level two certification (if applicable): Hand guards shall be made of plastic. OPTIONAL Level three certification (if applicable): Hand guards should follow the correct RO shape, ANH hand guards are not acceptable. A small indent in the front of the hand plate shall be present. Gloves Black in color, made of Nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured. Rubber ANH style gloves are not permitted. OPTIONAL Level two certification (if applicable): The base material of the gloves will be a black synthetic material similar to Lycra, Spandex, Elastane, or Nylon. Palms of gloves shall be shiny black fabric or leather or leather-like material. On the index finger shall be a stitched piece of fabric made from the same material as the hand's underside that while stitched to the finger has one cutout towards the end of the finger that reveals the netted material underneath. Gloves shall have the correct leather pattern along the fingers/palm. OPTIONAL Level three certification (if applicable): Chest Armor Chest plate overlaps the abdominal plate OPTIONAL Level two certification (if applicable): There are raised trapezoids at the top of the shoulder section beneath which the straps insert. The chest and back sides shall be connected by black extensions pieces. OPTIONAL Level three certification (if applicable): Top pectoral out lines swoop correctly outward. Bottom of ribcage flares correctly outward. Back Armor Back plate contains an "O II" design. There are raised trapezoids at the top of the backplate section beneath which the shoulder straps insert. The backplate continues past these trapezoids towards the top of the shoulder OPTIONAL Level two certification (if applicable): Top of box wall has a trapezoidal indentation. There is a roughly 8mm circular indent near the right top corner of the backplate. OPTIONAL Level three certification (if applicable): Bottom of backplate is curved and extends past abdominal back cover plate. The O cog shall have 16 spines. The 11 bars have 5 horizontal evenly spaced raised bars on the bottom of the face. There is a rectangular tab protruding from the bottom of each of the two raised trapezoids at the top of the backplate. Abdomen Armor The abdominal armor consists of a one-piece corset design with a vertical opening centered on the back. The back opening is covered by a rectangular cover plate that is worn under the back armor. There are 3 vertical ribs centered on the front of the abdomen and two (one left and one right) ribs further spaced to each side of the center. There are two (one left and one right) angled (approximately 70 degrees) ribs on each side of the abdominal armor. There are two (one left and one right) angled (approximately 70 degrees) recessed ribs on each side of the abdominal armor behind the raised angled ribs that are black Any side shims added are to be added to the white areas of the armor. The center front detail consists of a raised rectangular panel. On the right half of the panel, there is a vertical column of 4 buttons approximately ⁷⁄₁₆" (11mm) in diameter. The bottom button is blue while the other three are grey. On the left half of the panel, there is a vertical column of raised evenly spaced horizontal gear teeth with a recessed trapezoid at the top of the column. The rectangular inside bottom of the trapezoid is black. The left front detail consists of a raised rectangular panel with an angled top. There is a vertical column of 4 buttons approximately ⁷⁄₁₆" (11mm) in diameter. The bottom button is blue while the other three are grey. The right front detail consists of a primary raised rectangular panel with an additional secondary raised rectangular panel covering the top ⅓ of the primary panel. There is a column of three thin horizontal evenly spaced raised lines across the top ½ of the secondary panel. The abdominal armor is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): The cod armor is separate from the abdominal armor. The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. OPTIONAL Level three certification (if applicable): The abdomen armor has two horizontal recessed rectangles centered above the center front detail panel and on each side of the center rib. All 8 Button details are recessed and bordered with a thin edge, only the recessed portion is painted. The center front panel column of raised gear teeth has only 9 teeth. There is a recessed edge (approximately ⅛" 3mm wide) along all four sides around the face of the center front panel The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. There is a recessed edge (approximately ⅛" 3mm wide) along the sides and top around the face of the left front detail pane The abdominal armor back cover plate has two protruding tabs along the bottom that rest inside the back hard belt. Cod Armor The cod armor consists of a body shape formed triangular plate with a raised center rib and raised lower portion and is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): The cod shall be a separate piece from the abdominal plate. OPTIONAL Level three certification (if applicable): Kidney Armor The kidney armor is separated in the back and covered by a rectangular plate. The rectangular plate is separate from the posterior armor. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Posterior Armor The posterior armor shall be a separate piece from the abdominal armor OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Belt The Ammunition belt consists of a hard belt made of the same or similar material as the armor in two separate parts front and back (with overlap). The back belt overlaps the front belt on the sides. There are 6 ammunition boxes mounted to the belt. There are 2 (one left and one right) drop boxes suspended by black webbing approximately 2" (50mm) wide. Drop boxes must be accurate in detail and proportion to official references. The ammunition belt is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): The only detail visible on the front belt is the mounted ammunition boxes unlike the squares present on ANH belts. The top edge of the front belt has protruding teeth that nest inside gaps between the ribs and detail panels of the abdominal armor. The two center ammunition boxes are thinner than the other mounted ammunition boxes. The second and fifth mounted ammunition boxes are slightly wider than the two center ammunition boxes. The two outermost ammunition boxes are almost square. The two drop boxes are rectangular and as wide as the mounted square boxes. OPTIONAL Level three certification (if applicable): The ammo boxes across the front are all made separately from the main belt and are secured to it The two drop boxes hang no more than 1" 25mm below the front belt and the black strap is visible. The second and fifth mounted ammunition boxes have trapezoid detail on the top of each ammunition box. The front belt protrudes past all mounted ammunition boxes above and below by approximately ⅛"–¼" 3–6mm. All ammunition boxes have slightly beveled edges on the face of each box. Thermal Detonator The thermal detonator consists of a grey tube approximately 3" 76mm in diameter and 8" 203mm long approximately. There are two white endcaps and a white control panel. The white control panel has a horizontal row of white rectangles along the bottom of the control panel and a grey “D” shaped recessed on the left side of the horizontal row. There is an oval greeble that protrudes from the control near the top right side. The thermal detonator is mounted to the rear hard belt and there are no visible screws or clips and is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): The thermal detonator mount should be fully enclosed with solid walls on all four sides. The center of both end caps is gray. OPTIONAL Level three certification (if applicable): The control panel bottom detail is a raised panel with 7 raised rectangles, all are evenly spaced except the right most rectangle. There is a panel line approximately ¼" 6mm from the edge around the control panel. There is a panel line approximately ⅛" 3mm from the edge of each endcap. The inside edge of both endcaps is beveled. The oval greeble consists of an oval tube protrusion with the top edge slightly extending past the tube wall thickness and is visually similar to the Deathtrooper chin greeble. Thigh Armor The thigh armor is mirrored for each leg and not interchangeable. The cover strips are beveled and approximately ⅛" thick that does not extend beyond the thigh and has a smaller cover strip layered thereon. The top edge of the thigh armor is unadorned, and the bottom edge has a raised detail that fallows the bottom edge contour. The small ammo belt consists of 5 evenly spaced rectangle ammunition boxes and is installed on the bottom of the right thigh, there are no visible screws or rivets. OPTIONAL Level two certification (if applicable): Thighs are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the front and rear joints. OPTIONAL Level three certification (if applicable): The bottom outside edges of the small ammunition belt are angled at approximately 45 degrees. Thigh armor is suspended by a black strap approximately 1" 25mm in width with a plastic side release buckle that is covered by black webbing or elastic that runs down the side seam of the leg. Lower Leg Armor The greaves are mirrored for each leg and are not interchangeable. The top edge of the greaves has a raised detail that fallows the top edge contour. The bottom edge of the greaves flairs out to cover the top of the ankle and boots. The cover strips are beveled and approximately ⅛" thick that does not extend beyond the greave and has a smaller cover strip layered thereon. Greaves are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the front and rear joints. The trapezoid knee plate (sniper knee plate) is affixed to the top of the left greave and there are no visible screws or rivets. Sniper knee plate must be aligned with the vertical cover strip and the top raised edge detail on the greave and is accurate in detail and proportion to official reference. OPTIONAL Level two certification (if applicable): The sniper knee plate has raised detail that fallows the top edge contour. The sniper knee plate has 3 trapezoidal lugs on each side and 2 on the center bottom edge (totalling 8) of the knee plate. OPTIONAL Level three certification (if applicable): Boots Boots are above ankle height and the same style as the First Order TK. Chelsea type boots in the style of OT TK are not acceptable. Boots are all white and made of leather or leather-like material Flat black soles without a heel. Patent leather or high gloss is not permitted. OPTIONAL Level two certification (if applicable): There is no seam present on the front of the boot. The wearer's inner side of the boots have zippers and no side elastic. OPTIONAL Level three certification (if applicable): Optional Accessories Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use. E-11 Blaster Manufactured by BlasTech Industries, the E-11 is standard-issue for many Imperial troops. Light, compact yet powerful, the E-11 blaster is always in high demand throughout the galaxy. "Note, the E-11 holster as seen in the Original Trilogy movies is not an authorized accessory for rogue One armor". Based on a real or replica Sterling Airsoft Gun, Sterling Sub-Machine Gun, scratch-built, or a modified commercial toy Stormtrooper blaster. A small flashlight shall can be mounted on the right side of the blaster centred over the T-Tracks. OPTIONAL Level two certification (if applicable): Blaster shall be based on a real or replica S&T Sterling L2A1 AEG Airsoft Gun. (Folding Stock does not need to function) D-Ring shall be present on the rear end cap. Scope shall be a real or replica M.H.R. (Minneapolis Honeywell Regulator Co.) M38 Telescope. 1943 model is preferred. Counter shall be a real or replica Hengstler 400 Series counter. Eagle logo is preferred. Power Cylinders shall be mounted on top of the magazine well. R1 style power cylinders are preferred over ANH style. 6 rows of T-Tracks cover the Sterling receiver holes except for the lower left row with the bayonet lug. Flashlight if fitted shall be a real or replica Element M300A Mini Scout Light. 3D printed blasters can not contain visible print lines and must be sanded smooth for a more realistic appearance. OPTIONAL Level three certification (if applicable): Scope shall be a real or replica 1943 M.H.R. Co. M38 Telescope, 1942 model is not allowed. Counter shall be a real or replica Hengstler 400 Series counter with Small eagle logo. Large eagle logo is not allowed. Power Cylinders shall be R1 style, ANH style is not allowed. BlasTech DLT-19 Heavy Blaster Rifle Based on a real or replica MG-34 machine. OPTIONAL Level two certification (if applicable): A DLT-19 is an MG-34 with T-tracks on the barrel, ejection port cover added, and a small disk on left side. 3D printed blasters can not contain visible print lines and must be sanded smooth for a more realistic appearance. OPTIONAL Level three certification (if applicable): A small flashlight shall can be mounted on the right side of the blaster forward the front sight. BlasTech T-21 Light Repeating Blaster Rifle Based on a real or replica Lewis Mark I machine gun. For this prop the magazine disk and bipod of the original gun are left off. Rubber or rubber-like tubing is wrapped around the barrel shroud covering about ½ the length of the shroud. A small flashlight shall be mounted on the right side of the blaster forward the front sight. OPTIONAL Level two certification (if applicable): A black nylon 2-point sling shall be attached. Front sight shall be present on top of forward most large barrel ring. 3D printed blasters can not contain visible print lines and must be sanded smooth for a more realistic appearance. OPTIONAL Level three certification (if applicable): Three large barrel shroud rings are present, two before the rubber tubbing and one prior to the shroud transition. Small barrel ring is present at end of the barrel. Charging handle is mounted on right side of the blaster. Gas Key Adjustment Lever greeble is mounted on the bottom of barrel shroud before forward most large barrel ring. Oil Cleaning Brush greebles are mounted on stock. Sling is mounted to blaster and stock and not wrapped around either. Flashlight shall be a real or replica Element M300A Mini Scout Light. Baton and holster Flat or matte black in color, free of adornment or decoration. Is composed of three sections that extend outward when in use. When not in use, it appears as one cylinder. Is approximately 14" long when collapsed and 1" in diameter. The baton hangs off of the left rear belt, on a black holster. It is be attached at two points on the holster: one at the top, and one at the bottom. The baton should not swing when holstered. The holster is made from leather or leather-like material. OPTIONAL Level two certification (if applicable): 3D printed blasters and any approvable accessories can not contain visible print lines and must be sanded smooth for a more realistic appearance. Imperial Binders Imperial binders accurate in detail and proportion to official references is an authorized accessory. OPTIONAL Level two certification (if applicable): 3D printed blasters and any approvable accessories can not contain visible print lines and must be sanded smooth for a more realistic appearance. Tk rogue one pauldron.jpg Pauldron Rogue One Pauldrons denote rank or mission specialization. The Rogue One Pauldron is specific to Rogue One and differs from the original trilogy in color and stitching. Original trilogy Pauldrons are not an authorized accessory for Rogue One armor. An Orange, white, or black ornament made of leather plastic or leather-like material, worn over the right shoulder. The Orange is specific to Rogue One and a different shade from the original trilogy. The colored panel is divided into three sections by color matched stitching to conform to the wearers shoulder and has black piping around the outside edge. The remainder of the Pauldron is black and divided by black stitching into 10 segments. The neck closure is black and has two black snaps visible. There is a black elastic strap that runs from back to front and is worn under the bicep to hold the Pauldron in place. The strap is conned to the Pauldron on top by two black snaps inlayed in black “D” shaped leather or leather-like ends. The underside of the Pauldron is white regardless of top color and is divided with white stitching into 13 segments. The entire outside edge is finished with black piping and the underside of the neck closure is black. Comlink A comlink may be worn on the belt

I have a pair of TK boots and I don't like how wide they are at the top. They don't fit under my shin armor. Instead of getting the white leather boots most folks get, I'd rather get a pair of black Chelsea boots and paint them. I did look them up and there were quite a lot. Is there a favorite in the community for this purpose? Thank you all so much in advance! Sent from my SM-N960U using Tapatalk

-- EDIT 08/31/2022-- Future Jason here, I just wanted to provide this colorful edit to help explain how I'm going to handle additions to this original post. Initially, I was striking out verbiage as it was written, then adding new text, but it was getting messy. I will continue using strike through text whenever I remove something from the existing CRL, but will follow that up with red text indicating the agreed upon change. Of note, I will try not to make any of these changes unless it's captured in this conversation, but I am receiving input from detachment leadership in addition to what's captured here. If anything ever appears in the CRL text below that a person does not recall discussing, please let us know so the discussion can continue. What I absolutely refuse to do is create ambiguous text, or what I refer to as a "moving target CRL." Any edits to my original post will be written in yellow so you can follow the changes easier; I will also date any revision/ edit. So again, CRL changes/ additions in red instructions/ original post edits in yellow. Thanks, TK-51923 Fellow TKs. After several discussions regarding the inclusion of Remnant Stormtroopers, as seen in The Mandalorian seasons 1 and 2 into the Databank, we have decided to move forward with the creation of a CRL. The goal in developing this thread is to create a CRL specific to the heavily weathered Remnants serving Werner Herzog's "The Client" as well as those seen in Season 2 episode 7 The Believer, working in the rhydonium refinery on the planet Morak. For previous discussion on this topic, please see the following thread: https://www.whitearmor.net/forum/topic/48305-new-anthology-tk-crl/ Additionally, for reference, please see the following picture: Additionally, since we have several new references to draw from since the creation of the original Rogue One TK CRL and it's subsequent revision in 2020, this thread will also serve to address revisions to the current ROTK CRL and the potential creation of a separate CRL for the New Generation/ Anthology TK. Discussions are ongoing regarding how to handle this generation of TK armor that has become synonymous with the Anthology films and various Disney+ series. This includes the existing ROTK, which could be renamed, receive additional variations, remain unchanged, or none of the above. However, one item that has been emphasized to me from detachment staff is that we have to clearly show that this is a unique set of armor without stating "it's dirty." Additionally, we have found several instances in which items were either missing, broken, or taped together by the costume department for the respective productions; these discrepancies will not be included in any new CRL or revisions to existing CRLs. The goal of this thread is to identify the unique attributes of the costume that are uniform throughout all of it's appearances in Anthology films and Disney+ productions, not to capture broken or missing items. Things that will not be considered: broken thigh armor, drop boxes tucked into the thighs or missing altogether, missing TDs, and "$#1++y wardrobe dressing or stunt men with gaffer tape." I'm not going to say who's quote that was. With that said, we obviously have an ANH OT bucket resting atop Rogue One style armor. These are on prominent display, but there's other unique characteristics as well. This is our opportunity to post them up and start hashing out the details. Please take a look at the aforementioned thread, but I also intend on posting several of the pictures here. To get started, I will post the verbiage from our current ROTK CRL, and include the wording from the ANH Stunt helmet. I will continue updating everything as we go along and highlight any changes in red. Additionally, even though this isn't a New Generation/ Anthology CRL, we need to capture anything in the New Generation gear that hasn't been covered previously. If there's new things that have been discovered, please post them. Let's get started: Helmet Moderate to heavily weathered 8/24/2022 Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray. Rear traps and tears have vertical black lines. Lenses are flat material, green in color, sufficiently dark enough to obscure the costumer's eyes. The “ear” bars have three or four bumps and are gray or painted gray, with a black outline. Painting the bumps with rank stripes (highlighted) in black is optional. Frown is painted gray and does not leave the teeth area. A total of 8 cut outs in the teeth area of the frown are present. Tube stripes are medium blue, numbering between 9 and 16 per side with the curve bends extending backwards. Vocoder (vertically ribbed chin detail) is painted black. Aerators/Hovi-MIX tips (cylinders on either side of the vocoder) are black or painted black. Tears, traps, and tube stripes may be hand painted, decals, or decals that replicate hand painted. Mesh may be used behind the frown to obscure the face of the wearer. Note: The helmet is accurate in detail and proportion to official references. Many commercially available helmets or those considered disproportionate in size or shape are ineligible. OPTIONAL Level two certification (if applicable): Ears shall have three screws per side, one above and one below the ear bar and one at the base of the helmet. Ear bars have four bumps only. Not three. Traps/tears and tube stripes shall have the correct ANH TK details. Ideally, the tube stripes are positioned approximately a pencil width from the side of the cheek. Fall of tube stripe tops ideally lean toward the front. Correct Aerators/Hovi-MIX tips are present. Screens used shall be of a wide type mesh, with the rim of the mic and the inside white or painted white. OPTIONAL Level three certification (if applicable): Ear bars shall have only one bump painted in black (rank stripes). Ideally, placement of ears (and screws) should closely follow the rear angle of the trap above them Neck trim shall be of an s-type profile rather than a u-type profile. Tears/traps shall be hand painted or use decals that emulate hand painted (with correct ANH TK details). Ear screws shall be slotted, flat topped, countersunk and painted white. The vocoder must be integrated into the helmet, and not a separate piece. Neck Seal Moderate to heavily weathered 8/24/2022 Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to conceal the entire neck Under Suit Moderate to heavily weathered 8/24/2022 Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs. OPTIONAL Level two certification (if applicable): Top, where visible shall be fully ribbed with all horizontal ribbing on the arms, chest, and back. The centre of chest and back may be mesh as long as it is covered by armor. Pants shall be black non-textured material and have horizontal ribbing at the knees only. Knee gaskets are allowed as long as they correctly match top ribbing material, spacing and color. The hip section shall not have ribs. OPTIONAL Level three certification (if applicable): All ribbing on knees, arms, chest, and back must be stitched between each rib in detail and proportion to official references. The armpit area shall have the correct hexagonal mesh detail Shoulder Straps Moderate to heavily weathered 8/24/2022 They may be affixed with Velcro or adhesive. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): These shall be inserted behind the chest tabs and into slots of the backplate. Shoulder Armor Moderate to heavily weathered 8/24/2022 One on each shoulder. The shoulders are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders and may have a black elastic strap that wraps around the inside of the bicep. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): There is no swoop on the shoulder bell raised area. There is no elastic strap that wraps around the inside of the bicep. Upper Arm (Bicep) Armor 8/31/2022 Moderate to heavily weathered 8/24/2022 Both biceps are symmetrical and interchangeable. The front strip is bevelled and approximately 1/8" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Cover strips will cover both the front and back joints. Biceps are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. The biceps are suspended from the shoulder armor via shock cord (bungee/ framilon cordage) via "J hooks" at the top of the biceps per the screen references. 8/31/2022 A separate piece of white 1" webbing or elastic, extends from the shoulder armor, through a slot in the bicep per the screen references. 8/31/2022 Forearm Armor Moderate to heavily weathered 8/24/2022 The front strip is bevelled and approximately 1/8" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Forearms are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the top and bottom joints. Hand Plates Moderate to heavily weathered 8/24/2022 Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material. OPTIONAL Level two certification (if applicable): Hand guards shall be made of plastic. OPTIONAL Level three certification (if applicable): Hand guards should follow the correct RO shape, ANH hand guards are not acceptable. A small indent in the front of the hand plate shall be present. Gloves Moderate to heavily weathered 8/24/2022 Black in color, made of either rubber, Nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured. OPTIONAL Level two certification (if applicable): Gloves shall not be made of rubber. OPTIONAL Level three certification (if applicable): The base material of the gloves will be a black synthetic material similar to Lycra, Spandex, Elastane, or Nylon. Palms of gloves shall be shiny black fabric or leather or leather-like material. On the index finger shall be a stitched piece of fabric made from the same material as the hand's underside that while stitched to the finger has one cutout towards the end of the finger that reveals the netted material underneath. Gloves shall have the correct leather pattern along the fingers/palm. Chest Armor Moderate to heavily weathered 8/24/2022 Chest plate overlaps the abdominal plate OPTIONAL Level two certification (if applicable): There are raised trapezoids at the top of the shoulder section beneath which the straps insert. The chest and back sides shall be connected by black extensions pieces. OPTIONAL Level three certification (if applicable): Top pectoral out lines swoop correctly outward. Bottom of ribcage flares correctly outward. Back Armor Moderate to heavily weathered 8/24/2022 Back plate contains an "O II" design. There are raised trapezoids at the top of the backplate section beneath which the shoulder straps insert. The backplate continues past these trapezoids towards the top of the shoulder OPTIONAL Level two certification (if applicable): Top of box wall has a trapezoidal indentation. There is a roughly 8mm circular indent near the right top corner of the backplate. OPTIONAL Level three certification (if applicable): Bottom of backplate is curved and extends past abdominal back cover plate. The O cog shall have 16 spines. The 11 bars have 5 horizontal evenly spaced raised bars on the bottom of the face. There is a rectangular tab protruding from the bottom of each of the two raised trapezoids at the top of the backplate. Abdomen Armor Moderate to heavily weathered 8/24/2022 The abdominal armor consists of a one-piece corset design with a vertical opening centred on the back. The back opening is covered by a rectangular cover plate that is worn under the back armor. There are 3 vertical ribs centered on the front of the abdomen and two (one left and one right) ribs further spaced to each side of the center. There are two (one left and one right) angled (approximately 70 degrees) ribs on each side of the abdominal armor. There are two (one left and one right) angled (approximately 70 degrees) recessed ribs on each side of the abdominal armor behind the raised angled ribs that are black Any side shims added are to be added to the white areas of the armor. The center front detail consists of a raised rectangular panel. On the right half of the panel, there is a vertical column of 4 buttons approximately 7/16” (11mm) in diameter. The bottom button is blue while the other three are grey. On the left half of the panel, there is a vertical column of raised evenly spaced horizontal gear teeth with a recessed trapezoid at the top of the column. The rectangular inside bottom of the trapezoid is black. The left front detail consists of a raised rectangular panel with an angled top. There is a vertical column of 4 buttons approximately 7/16” (11mm) in diameter. The bottom button is blue while the other three are grey. The right front detail consists of a primary raised rectangular panel with an additional secondary raised rectangular panel covering the top 1/3 of the primary panel. There is a column of three thin horizontal evenly spaced raised lines across the top ½ of the secondary panel. The abdominal armor is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): The cod armor is separate from the abdominal armour. The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. OPTIONAL Level three certification (if applicable): The abdomen armor has two horizontal recessed rectangles centred above the center front detail panel and on each side of the center rib. All 8 Button details are recessed and bordered with a thin edge, only the recessed portion is painted. The center front panel column of raised gear teeth has only 9 teeth. There is a recessed edge (approximately 1/8” 3mm wide) along all four sides around the face of the center front panel The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. There is a recessed edge (approximately 1/8” 3mm wide) along the sides and top around the face of the left front detail pane The abdominal armor back cover plate has two protruding tabs along the bottom that rest inside the back hard belt. Move to "kidney armor" section. Cod Armor Moderate to heavily weathered 8/24/2022 The cod armor consists of a body shape formed triangular plate with a raised center rib and raised lower portion and is accurate in detail and proportion to official references. The cod shall be a separate piece from the abdominal plate 8/31/2022 Removed from Level Two certification. Having this as a level 2 requirement instead of basic may lead people to use OT amor in constructing their kits or create abdominal/ cod pieces that are not accurate to any available references for this costume. OPTIONAL Level two certification (if applicable): The cod shall be a separate piece from the abdominal plate. OPTIONAL Level three certification (if applicable): Kidney Armor Moderate to heavily weathered 8/24/2022 The kidney armor is separated in the back and covered by a rectangular kidney/ trauma plate. 8/31/2022 The rectangular plate is separate from the posterior armor and sits above the rear hard belt. 8/31/2022 OPTIONAL Level two certification (if applicable): The kidney/ trauma plate is large enough to cover the entire gap present in the rear of the abdominal armor and extends up underneath the back armor. 8/31/2022 OPTIONAL Level three certification (if applicable): The kidney armor cover plate has two protruding tabs along the bottom that rest inside the back hard belt. Posterior Armor Moderate to heavily weathered 8/24/2022 The posterior armor shall be a separate piece from the abdominal armor OPTIONAL Level two certification (if applicable): Belt Moderate to heavily weathered 8/24/2022 The Ammunition belt consists of a hard belt made of the same or similar material as the armor in two separate parts front and back (with overlap). The back front belt overlaps the front rear belt on the sides. 8/31/2022 There are 6 ammunition boxes mounted to the belt. There are 2 (one left and one right) drop boxes suspended by black webbing approximately 2" (50mm) wide. Drop boxes must be accurate in detail and proportion to official references. The ammunition belt is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): The only detail visible on the front belt is the mounted ammunition boxes unlike the squares present on ANH belts. The top edge of the front belt has protruding teeth that nest inside gaps between the ribs and detail panels of the abdominal armor. The two center ammunition boxes are thinner than the other mounted ammunition boxes. The second and fifth mounted ammunition boxes are slightly wider than the two center ammunition boxes. The two outermost ammunition boxes are almost square. The two drop boxes are rectangular and as wide as the mounted square boxes. OPTIONAL Level three certification (if applicable): The ammo boxes across the front are all made separately from the main belt and are secured to it The two drop boxes hang no more than 1” 25mm below the front belt and the black strap is visible. The second and fifth mounted ammunition boxes have a trapezoid detail on the top of each ammunition box. The trapezoid detail is a triangular prism that has no rounded edges. 8/31/2022 The front belt protrudes past above all mounted ammunition boxes above and below by approximately 1/8”-1/4” 3-6mm. The front belt protrudes approximately 1/2" below the front 4 ammo boxes in a trapezoidal shape that extends from the center of both medium sized ammo boxes where it tapers to 1/8"-1/4" (3-6mm) below the ammo boxes across the remaining span of the belt per the official references. 8/31/2022 All ammunition boxes, including the drop boxes, have slightly bevelled chamfered edges on the face of each box. 8/31/2022 Thermal Detonator Moderate to heavily weathered 8/24/2022 The thermal detonator consists of a grey tube approximately 3” 76mm in diameter and 8” 203mm long approximately. There are two white endcaps and a white control panel. The white control panel has a horizontal row of white rectangles along the bottom of the control panel and a grey “D” shaped recessed on the left side of the horizontal row. There is an oval greeble that protrudes from the control near the top right side. The thermal detonator is mounted to the rear hard belt and there are no visible screws or clips and is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): The thermal detonator mount should be fully enclosed with solid walls on all four sides. The center of both end caps is gray. OPTIONAL Level three certification (if applicable): The control panel bottom detail is a raised panel with 7 raised rectangles, all are evenly spaced except the right most rectangle. There is a panel line approximately ¼” 6mm from the edge around the control panel. There is a panel line approximately 1/8” 3mm from the edge of each endcap. The inside edge of both endcaps is bevelled. The oval greeble consists of an oval tube protrusion with the top edge slightly extending past the tube wall thickness and is visually similar to the Deathtrooper chin greeble. The thermal detonator is made separate from the mount and secured to it. 8/31/2022 I added this due to the number of instances in which we've seen the TD disconnected from it's mount or missing on screen. Similar to the belt boxes, the TD should be separate, but fixed to the mount appropriately as per the screen references. Thigh Armor Moderate to heavily weathered 8/24/2022 The thigh armor is mirrored for each leg and not interchangeable. The cover strips are bevelled and approximately 1/8" thick that does not extend beyond the thigh and has a smaller cover strip layered thereon. The top edge of the thigh armor is unadorned, and the bottom edge has a raised detail that fallows the bottom edge contour. The small ammo belt consists of 5 evenly spaced rectangle ammunition boxes and is installed on the bottom of the right thigh, there are no visible screws or rivets. OPTIONAL Level two certification (if applicable): Thighs are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. 8/31/2022 Thigh armor has been seen several times separated (flexible) in the rear, but never worn in the same manner as the arms (bungee cords/ framilon cordage). Cover strips will cover both the front and rear joints. Rear cover strips will close outside over inside, i.e. left over right for the left thigh and Right over Left for the right thigh. 8/31/2022 OPTIONAL Level three certification (if applicable): The bottom outside edges of the small ammunition belt are angled chamfered at approximately 45 degrees. Thigh armor is suspended by a black strap approximately 1” 25mm in width with a plastic side release buckle tri-glide buckle that is covered by black webbing fabric or elastic that runs down the side seam of the leg. 8/31/2022 Lower Leg Armor Moderate to heavily weathered 8/24/2022 The greaves are mirrored for each leg and are not interchangeable. The top edge of the greaves has a raised detail that fallows the top edge contour. The bottom edge of the greaves flairs out to cover the top of the ankle and boots. The cover strips are bevelled and approximately 1/8" thick that does not extend beyond the greave and has a smaller cover strip layered thereon. Greaves are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the front and rear joints. The trapezoid knee plate (sniper knee plate) is affixed to the top of the left greave and there are no visible screws or rivets. Sniper knee plate must be aligned with the vertical cover strip and the top raised edge detail on the greave and is accurate in detail and proportion to official reference. OPTIONAL Level two certification (if applicable): The sniper knee plate has raised detail that fallows the top edge contour. The sniper knee plate has 3 trapezoidal lugs on each side and 2 on the center bottom edge (totalling 8) of the knee plate. OPTIONAL Level three certification (if applicable): Boots Moderate to heavily weathered 8/24/2022 Boots are above ankle height and the same style as the First Order TK. Chelsea type boots in the style of OT TK are not acceptable. Boots are all white and made of leather or leather-like material Flat black soles without a heel. Patent leather or high gloss is not permitted. OPTIONAL Level two certification (if applicable): There is no seam present on the front of the boot. The wearer's inner side of the boots have zippers and no side elastic. OPTIONAL Level three certification (if applicable): Optional Accessories Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use. E-11 Blaster Weathering is optional 8/24/2022 Manufactured by BlasTech Industries, the E-11 is standard-issue for many Imperial troops. Light, compact yet powerful, the E-11 blaster is always in high demand throughout the galaxy. "Note, the E-11 holster as seen in the Original Trilogy movies is not an authorized accessory for rogue One armor". Based on a real or replica Sterling Airsoft Gun, Sterling Sub-Machine Gun, scratch-built, or a modified commercial toy Stormtrooper blaster. A small flashlight shall be mounted on the right side of the blaster centred over the T-Tracks. OPTIONAL Level two certification (if applicable): Blaster shall be based on a real or replica S&T Sterling L2A1 AEG Airsoft Gun. (Folding Stock does not need to function) D-Ring shall be present on the rear end cap. Scope shall be a real or replica M.H.R. (Minneapolis Honeywell Regulator Co.) M38 Telescope. 1943 model is preferred. Counter shall be a real or replica Hengstler 400 Series counter. Eagle logo is preferred. Power Cylinders shall be mounted on top of the magazine well. R1 style power cylinders are preferred over ANH style. 6 rows of T-Tracks cover the Sterling receiver holes except for the lower left row with the bayonet lug. Flashlight shall be a real or replica Element M300A Mini Scout Light. 3D printed blasters can not contain visible print lines and must be sanded smooth for a more realistic appearance. OPTIONAL Level three certification (if applicable): Scope shall be a real or replica 1943 M.H.R. Co. M38 Telescope, 1942 model is not allowed. Counter shall be a real or replica Hengstler 400 Series counter with Small eagle logo. Large eagle logo is not allowed. Power Cylinders shall be R1 style, ANH style is not allowed. SE-14r Light Repeating Blaster Weathering is optional 8/24/2022 SE-14r Light Repeating Blaster. The barrel detailing is evident with the cocking lever and slider in place. The ejection port is also evident. The scope mount looks similar to the magazine but smaller in size. OPTIONAL Level two certification (if applicable): E-22 Blaster Weathering is optional 8/24/2022 Based on a real or replica Sterling sub-machine gun, scratch-built, cast, 3D print or a modified commercial toy Stormtrooper blaster. It has a extended stock attached at the rear and a extended front housing with second lower barrel. Tactical flashlight (Surefire scout M300 or replica) mounted on right side of barrel. Magazine is extended length. Power cylinder is larger with 2 outer cylinders and 2 smaller central cylinders Scope is a M38 1943 version Scope rail is fitted onto rail blocks, one inside the rear sight and the other at the front end of the rail. There are 3 swivel studs fitted, one on the rear stock and one each side of the front barrel housing. Sling is 25mm webbing strap that is adjustable using a silver 25mm 3 fixed bar webbing buckle (optional). Sling is fitted with Talon quick release 25mm swivel or replica (optional). Red lights fitted on both sides of the rear housing, Hengstler fitted with a red light for the 3 forward tubes and 2 small red lights fitted into the rear barrel housing under the torch, the lights are permanent and are non flashing or pulsed (optional hero version only). OPTIONAL Level two certification (if applicable): Base is based on S&T Airsoft sterling with closed working parts (no spring) Screws used are M4 x 25mm Allen screw/bolts and sunken Allen screws for power cylinders Sling is fitted with Talon quick release 25mm swivel. Pauldron Rogue One Pauldrons denote rank or mission specialization. The Rogue One Pauldron is specific to Rogue One and differs from the original trilogy in color and stitching. Original trilogy Pauldrons are not an authorized accessory for Rogue One armor. An Orange, white, or black ornament made of leather plastic or leather-like material, worn over the right shoulder. The Orange is specific to Rogue One and a different shade from the original trilogy. A red pauldron as seen in The Mandalorian Chapter 14, may be worn as part of the New Generation TK costume, but not as a Rogue One stormtrooper. 8/31/2022 The colored panel is divided into three sections by color matched stitching to conform to the wearers shoulder and has black piping around the outside edge. The remainder of the Pauldron is black and divided by black stitching into 10 segments. The neck closure is black and has two black snaps visible. There is a black elastic strap that runs from back to front and is worn under the bicep to hold the Pauldron in place. The strap is conned to the Pauldron on top by two black snaps inlayed in black “D” shaped leather or leather-like ends. The underside of the Pauldron is white regardless of top color and is divided with white stitching into 13 segments. The entire outside edge is finished with black piping and the underside of the neck closure is black. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable):

Hi, just wondered if anyone knows if there's a screen accurate, 501st acceptable PU (faux leather) Chelsea boot out there? I have seen FO TK PU leather boots on Jedi robes website but obviously these are no good ANH TK compatibility . thanks for any info. Cheers

I saw that these chelsea boots are on sale at Kohls right now. They seem like a good possibility for converting to white, and don't have any seams on the front. There is even an extra $10 off with code. Of course, they are imitation, not real leather, though. What do you guys think? https://www.kohls.com/product/prd-2911525/apt-9-edgewood-mens-chelsea-boots.jsp?color=Black&prdPV=4

Does the community have a recommendation for low-cost (<$100) boots? For around $50 I can purchase a pair of black leather deer stag boots and possibly paint them or purchase a finished pair on Etsy for around $60-$70. I'm inclined to go with the Amazon boots since they are cheaper and seem more durable but I am not sure which paint to use. Link to Amazon boots: https://www.amazon.com/Deer-Stags-Rockland-Comfort-Chelsea/dp/B07C2XWH9H/ref=sr_1_6?crid=1J0HKUX4K4XLR&keywords=Mens%2BChelsea%2Bboot&qid=1690264763&sprefix=mens%2Bchelsea%2Bboot%2Caps%2C110&sr=8-6&th=1&psc=1)

I’m beginning a build or technically refurbishing a used set of what was listed as AP armor and would like to make Centurion. I’ll be scrubbing the threads for insights but your feedback and suggestions are welcome! Here’s a pic for reference. I’m having trouble finding boots in size 13, but happen to do leather work as a hobby so I may paint some Chelsea boots and seal them. I found these and they appear to be CRL standard: Deer Stags Men's Rockland Chelsea Boot https://a.co/d/00lhSi1 obviously I’ll be painting them white and will black out the sole threads. Thoughts?

Artillery Trooper CRL First Draft The Rogue One CRL was used as the base considering it is the same armour, so level 2 and 3 also easily apply. Helmet Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray. Rear traps and tears have engraved vertical black lines. Lenses can be flat material, green in color, sufficiently dark enough to obscure the costumer's eyes. The “ear” bars are gray or painted gray, with the largest bar oval cutout painted black. Frown is painted gray and does not leave the teeth area. The space between the 8 teeth is hollow and backed with Black or Dark grey wire screen mesh. Tube stripes are medium blue, numbering 12 per side. The stipes are straight, not curved like ANH. Vocoder (vertically ribbed chin detail) is painted black. Aerators/Hovi mix tips (cylinders on either side of the vocoder) have a black exterior and silver in color screen mesh. Tears and traps may not be hand-painted. Tube stripes are recessed, and the recessed section painted blue or backed by blue mesh. Special unit details in yellow shall be present. The yellow detail will start from the back of the dome, continue over the head, down the face plate and ends underneath the chin area at the neck seal. Helmet and details/paint should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD) Note: The helmet is accurate in detail and proportion to official references. Many commercially available helmets or those considered disproportionate in size or shape are ineligible. The Black Series helmet is approvable if modified to meet the level 1 CRLs. OPTIONAL Level two certification (if applicable): Lenses have a very slight curve and are convex in style. Flat lenses and ANH style bubble lenses are not permissible. Rank bar area on ear must be of the correct RO style and pattern, no ANH style ear bumps allowed. Head opening has black trim running all along the edge. Brow trim should be positioned 1/4" above the eyes. Ear screws must not have a visible slot mark and be flush to the ear. Any gap between the ears and helmet will only appear to be a seam, not any bigger. Correct 'Hovi mic' aerator tips. Chin section has a well defined seam from the angles of the mouth. OPTIONAL Level three certification (if applicable): The Tube stripes are completely hollowed out with a blue section underneath. Vocoder is tubular in nature with 7 vertical tubes. A visible gap must be present between the Vocoder and the helmet. The inside of each tear will be a raised area that is grey, with 8 engraved black lines, hand painted lines like ANH are not permitted. The frown shall be recessed to the proper depth, unlike standard ANH. The inside of each rear trap will be a raised area that is grey, with 13 engraved black vertical lines, hand painted lines like ANH are not permitted. The inside of each side trap will be a raised area that is grey. There is a small bump in the right eye socket (when worn) under the lens as an intended flaw to pay tribute to the original trilogy designers. Neck Seal Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to conceal the entire neck. Under Suit Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs. OPTIONAL Level two certification (if applicable): Top, where visible shall be fully ribbed with all horizontal ribbing on the arms, chest, and back. The centre of chest and back may be mesh as long as it is covered by armor. Pants shall be black non-textured material and have horizontal ribbing at the knees only. Knee gaskets are allowed as long as they correctly match top ribbing material, spacing and color. The hip section shall not have ribs. OPTIONAL Level three certification (if applicable): All ribbing on knees, arms, chest, and back must be stitched between each rib in detail and proportion to official references. The armpit area shall have the correct hexagonal mesh detail. Shoulder Armor One on each shoulder. The shoulders are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders and may have a black elastic strap that wraps around the inside of the bicep. Special unit details in yellow shall be present along the outside edge. Shoulder bells/Special unit details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD) OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): There is no swoop on the shoulder bell raised area. There is no elastic strap that wraps around the inside of the bicep. Shoulder Strap They may be affixed with Velcro or adhesive. OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): These shall be inserted behind the chest tabs and into slots of the backplate. Upper Arm Armour Both biceps are symmetrical and interchangeable. The front strip is beveled and approximately 1/8" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. Special unit details in yellow shall be present in the form of one vertical stripe, running the length of the bicep. The stripe covers the front cover strip top and sides. Bicep/Special unit details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD) . OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Cover strips will cover both the front and back joints. Biceps are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Forearm Armor The front strip is beveled and approximately 1/8" thick that does not extend beyond the bicep, and has a smaller cover strip layered thereon. Special unit details in yellow shall be present in the form of two vertical stripes, running the length of the forearm. One on the front (cover strip area top and sides of strip), the other on the outside raised section containing the 12 indents. This stripe is only on the top surface, not on the sides of the raised area. Forearm/Special unit details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). OPTIONAL Level two certification (if applicable): OPTIONAL Level three certification (if applicable): Forearms are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the top and bottom joints. Hand Plates Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material. Special unit details in yellow shall be present in the form of vertical stripe that runs down the center ridge of each hand plate. It continues approximately 3/4 of the way onto the wrist end section of the plate, finishing with a foot like shape as per visual references. Hand plate/Special unit details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD) OPTIONAL Level two certification (if applicable): Hand guards shall be made of plastic. OPTIONAL Level three certification (if applicable): Hand guards should follow the correct RO shape, ANH hand guards are not acceptable. A small indent in the front of the hand plate shall be present. Gloves Black in color, made of either rubber, Nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured. OPTIONAL Level two certification (if applicable): Gloves shall not be made of rubber. OPTIONAL Level three certification (if applicable): The base material of the gloves will be a black synthetic material similar to Lycra, Spandex, Elastane, or Nylon. Palms of gloves shall be shiny black fabric or leather or leather-like material. On the index finger shall be a stitched piece of fabric made from the same material as the hand's underside that while stitched to the finger has one cutout towards the end of the finger that reveals the netted material underneath. Gloves shall have the correct leather pattern along the fingers/palm. Back Armor Back plate contains an "O II" design. There are raised trapezoids at the top of the backplate section beneath which the shoulder straps insert. The backplate continues past these trapezoids towards the top of the shoulder OPTIONAL Level two certification (if applicable): Top of box wall has a trapezoidal indentation. There is a roughly 8mm circular indent near the right top corner of the backplate. OPTIONAL Level three certification (if applicable): Bottom of backplate is curved and extends past abdominal back cover plate. The O cog shall have 16 spines. The 11 bars have 5 horizontal evenly spaced raised bars on the bottom of the face. There is a rectangular tab protruding from the bottom of each of the two raised trapezoids at the top of the backplate. Chest Armor Chest plate overlaps the abdominal plate. There are raised trapezoids at the top of the shoulder section beneath which the straps insert. Special unit markings shall be present in yellow on the front. The yellow detail starts a few inches from the top/center, then flares out and runs along the bottom edge. Chest/special unit details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). OPTIONAL Level two certification (if applicable): The chest and back sides shall be connected by black extensions pieces. OPTIONAL Level three certification (if applicable): Top pectoral out lines swoop correctly outward. Bottom of ribcage flares correctly outward. Abdomen Armor The abdominal armor consists of a one-piece corset design with a vertical opening centred on the back. The back opening is covered by a rectangular cover plate that is worn under the back armor. There are 3 vertical ribs centered on the front of the abdomen and two (one left and one right) ribs further spaced to each side of the center. There are two (one left and one right) angled (approximately 70 degrees) ribs on each side of the abdominal armor. There are two (one left and one right) angled (approximately 70 degrees) recessed ribs on each side of the abdominal armor behind the raised angled ribs that are black. Any side shims added are to be added to the white areas of the armor. The center front detail consists of a raised rectangular panel. On the right half of the panel, there is a vertical column of 4 buttons approximately 7/16” (11mm) in diameter. The bottom button is blue while the other three are grey. On the left half of the panel, there is a vertical column of raised evenly spaced horizontal gear teeth with a recessed trapezoid at the top of the column. The rectangular inside bottom of the trapezoid is black. The left front detail consists of a raised rectangular panel with an angled top. There is a vertical column of 4 buttons approximately 7/16” (11mm) in diameter. The bottom button is blue while the other three are grey. The right front detail consists of a primary raised rectangular panel with an additional secondary raised rectangular panel covering the top 1/3 of the primary panel. There is a column of three thin horizontal evenly spaced raised lines across the top ½ of the secondary panel. The abdominal armor is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): The cod armor is separate from the abdominal armour. The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. OPTIONAL Level three certification (if applicable): The abdomen armor has two horizontal recessed rectangles centred above the center front detail panel and on each side of the center rib. All 8 Button details are recessed and bordered with a thin edge, only the recessed portion is painted. The center front panel column of raised gear teeth has only 9 teeth. There is a recessed edge (approximately 1/8” 3mm wide) along all four sides around the face of the center front panel The right front detail panel is centered between the two outer vertical right ribs. The left front detail panel is centered between the two outer vertical left ribs. There is a recessed edge (approximately 1/8” 3mm wide) along the sides and top around the face of the left front detail pane The abdominal armor back cover plate has two protruding tabs along the bottom that rest inside the back hard belt. Cod Armor The cod armor consists of a body shape formed triangular plate with a raised center rib and raised lower portion and is accurate in detail and proportion to official references OPTIONAL Level two certification (if applicable): The cod shall be a separate piece from the abdominal plate. Kidney Armor The kidney armor is separated in the back and covered by a rectangular plate. The rectangular plate is separate from the posterior armor. Posterior Armor The posterior armor shall be a separate piece from the abdominal armor Belt The Ammunition belt consists of a hard belt made of the same or similar material as the armor in two separate parts front and back (with overlap). The back belt overlaps the front belt on the sides. There are 6 ammunition boxes mounted to the belt. There are 2 (one left and one right) drop boxes suspended by black webbing approximately 2" (50mm) wide. Drop boxes must be accurate in detail and proportion to official references. The ammunition belt is accurate in detail and proportion to official references. OPTIONAL Level two certification (if applicable): The only detail visible on the front belt is the mounted ammunition boxes unlike the squares present on ANH belts. The top edge of the front belt has protruding teeth that nest inside gaps between the ribs and detail panels of the abdominal armor. The two center ammunition boxes are thinner than the other mounted ammunition boxes. The second and fifth mounted ammunition boxes are slightly wider than the two center ammunition boxes. The two outermost ammunition boxes are almost square. The two drop boxes are rectangular and as wide as the mounted square boxes. OPTIONAL Level three certification (if applicable): The ammo boxes across the front are all made separately from the main belt and are secured to it The two drop boxes hang no more than 1” 25mm below the front belt and the black strap is visible. The second and fifth mounted ammunition boxes have trapezoid detail on the top of each ammunition box. The front belt protrudes past all mounted ammunition boxes above and below by approximately 1/8”-1/4” 3-6mm. All ammunition boxes have slightly bevelled edges on the face of each box. Thermal Detonator The thermal detonator consists of a grey tube approximately 3” 76mm in diameter and 8” 203mm long approximately. There are two white endcaps and a white control panel. The white control panel has a horizontal row of white rectangles along the bottom of the control panel and a grey “D” shaped recessed on the left side of the horizontal row. There is an oval greeble that protrudes from the control near the top right side. The thermal detonator is mounted to the rear hard belt and there are no visible screws or clips and is accurate in detail and proportion to official references. Thermal Detonator is only worn in absence of the munitions pack. OPTIONAL Level two certification (if applicable): The thermal detonator mount should be fully enclosed with solid walls on all four sides. The center of both end caps is gray. OPTIONAL Level three certification (if applicable): The control panel bottom detail is a raised panel with 7 raised rectangles, all are evenly spaced except the right most rectangle. There is a panel line approximately ¼” 6mm from the edge around the control panel. There is a panel line approximately 1/8” 3mm from the edge of each endcap. The inside edge of both endcaps is bevelled. The oval greeble consists of an oval tube protrusion with the top edge slightly extending past the tube wall thickness and is visually similar to the Deathtrooper chin greeble. Thigh Armor The thigh armor is mirrored for each leg and not interchangeable. The cover strips are bevelled and approximately 1/8" thick that does not extend beyond the thigh and has a smaller cover strip layered thereon. The top edge of the thigh armor is unadorned, and the bottom edge has a raised detail that fallows the bottom edge contour. The small ammo belt consists of 5 evenly spaced rectangle ammunition boxes and is installed on the bottom of the right thigh, there are no visible screws or rivets. The special unit markings shall be present in yellow along the top of the thigh, the markings shall continue approximately 2 inches further down the front cover strip as per references. Thighs/Special unit details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). OPTIONAL Level two certification (if applicable): Thighs are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the front and rear joints OPTIONAL Level three certification (if applicable): The bottom outside edges of the small ammunition belt are angled at approximately 45 degrees. Thigh armor is suspended by a black strap approximately 1” 25mm in width with a plastic side release buckle that is covered by black webbing or elastic that runs down the side seam of the leg. Lower Leg Armor The greaves are mirrored for each leg and are not interchangeable. The top edge of the greaves has a raised detail that follows the top edge contour. The bottom edge of the greaves flairs out to cover the top of the ankle and boots. The cover strips are bevelled and approximately 1/8" thick that does not extend beyond the greave and has a smaller cover strip layered thereon. Greaves are loosely held closed in the back with elastic, shock cord (bungee cord) or white Velcro and are designed to remain flexible. Cover strips will cover both the front and rear joints. The trapezoid knee plate (sniper knee plate) is affixed to the top of the left greave and there are no visible screws or rivets. Sniper knee plate must be aligned with the vertical cover strip and the top raised edge detail on the greave and is accurate in detail and proportion to official reference The base of the center trapezoid on the sniper plate is painted yellow. Special unit markings shall be present in yellow around the bottom of both greaves as per official references. Greave/Special unit details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). OPTIONAL Level two certification (if applicable): The sniper knee plate has raised detail that fallows the top edge contour. The sniper knee plate has 3 trapezoidal lugs on each side and 2 on the center bottom edge (totaling 8) of the knee plate. Boots Boots are above ankle height and the same style as the First Order TK. Chelsea type boots in the style of OT TK are not acceptable. Boots are all white and made of leather or leather-like material Flat black soles without a heel. Patent leather or high gloss is not permitted. Boots are lightly scuff and weathered. OPTIONAL Level two certification (if applicable): There is no seam present on the front of the boot. The wearer's inner side of the boots have zippers and no side elastic. Munitions Pack Pack must be accurate in colour and details styled after the munitions pack as seen in The Mandalorian season 2, and official reference images. Pack must be lightly scuffed and weathered. Pauldron UPDATED Although the Artillery Trooper is clad in Rogue One armor, the Pauldron that denote rank or mission specialization are an ANH style in construction. *A Yellow ornament made of leather plastic or leather-like material, worn over the right shoulder. The Yellow is specific to Rogue One/remnant as seen in The Mandalorian. *The colored panel is divided into three sections by color matched stitching to conform to the wearers shoulder and has black piping around the outside edge. *The remainder of the Pauldron is black and divided by black stitching into 10 segments. *The neck closure is black, it is mounted on top with two silver rivets and has two silver snaps visible. *There is a black elastic strap that runs from back to front and is worn under the bicep to hold the Pauldron in place. The strap is conned to the Pauldron on top by two black snaps inlayed in black “D” shaped leather or leather-like ends. *The underside of the Pauldron is white or black regardless of top color and is divided with white or black stitching into 3 segments. The entire outside edge is finished with black piping and the underside of the neck closure is black.||}} Merr-Sonn Munitions 201 telescopic mortar. *Launcher can be scratch-built, or 3D printed. *As with all 3D printed accessories, it can not contain visible print lines and must be sanded smooth for a more realistic appearance. *The Mortar shall match official reference and include A control panel shall be present on the left side of the mortar attached to the center section where the Bi pod also mounts as per references. *The mortar and details/paint should be lightly scuffed,(battle worn),similar to that of a blaster.

I’m trying to source boots on a shoestring (ha!) budget. I found out that the original boots in the films were dyed white. I’m not afraid to try that, so have now opened my search to other colors. I came across this Groupon link: ------ I have love-hate sentiments with Groupon, more towards the hate side of the spectrum. If it’s an item sold by a small business, it never hurts to call and ask if they will honor the price directly. Unless something has changed since I last dealt with them as a vendor (2014), there is absolutely nothing requiring you to sell your product through their website. Bypass them and you’re not shelling out upwards of 50% of the already discounted price to them. But I wanted to share: Discounted boots in the wrong color! Other than all the cons associated with dying, are these boots okayish?

Name: Sherry Thaxton TKID: 22725 Forum name: Adianu Garrison: Star Mandatory Information Armor = Walt's Trooper Factory Helmet= Walt's Trooper Factory (90% scale) Blaster= Hellhound Props 501st Membership Link Optional Height = 5'2" Weight = opting out on this one Boots = Self-painted Chelsea boots from Amazon Canvas belt = Self-made Hand Plates = JustJoseph Neck Seal = GeekyPink Holster = Self-made Full Body Front Back Left side (arms raised) and Left side detail Right side (arms raised) and 6. Right side detail Action shot Armor Details Abdomen button plates (close-up) Cod and posterior plate connections showing rivet/snaps (exterior) Interior strapping Wrist openings (close-up) Bonus details- Centurion prep Posterior plate/kidney connection Sniper knee plate (left and right sides) Knee ammo pack Helmet Details Front Left side Right side Rear Back-lit showing lens color Close-up of Hovi tips Bonus details- Centurion prep S-trim (side view) ear screw close-ups Vocoder Accessories Neck seal TD front and rear showing screw type Holster attachment ABS/canvas belt (rear) Boots (showing tops and sides) Rubber gloves Bonus details- Centurion prep Hand guards showing flexibility Blaster Details Left side Right side Rear showing D-ring I was spotty in updating it, but here is my build thread: https://www.whitearmor.net/forum/topic/46112-adianus-wtf-shorty-build/ I had help from a lot of TK's along the way, but especially want to thank Josh (https://www.whitearmor.net/forum/profile/32069-alotmorestuff/) from our South Texas Squad for answering countless questions, checking progress pictures, and helping me at armor parties! I appreciate feedback from everyone! I did build this intending to go for Centurion, so beyond EIB feedback appreciated as well.

Alright. Back at it we go. We drilled out our rivets and patched them up. We are still playing with buffing them down so it looks right. I'll post some pictures in a bit. The main thing I want to focus on today is boots. I've posted before that I have rather large feet and don't fit the standard trooper boots. I tried Crowprops, but it just didn't work out for me (James' were fine). Anyway, I'm at the point of sources new boots and found some Chelsea boots that I want to have painted. I'm thinking if just using these for trooping as I'm sure they aren't up to snuf, but I wasn't sure how all the rules around that worked. Please let me know if these boots would pass for general trooping? I have a pair to wear for when I submit, I just can't wear them that long.

So, apart from “ contact cfo “ or “ contact Tm “ does anyone have actual sources of the 2 1/4 nylon webbing for belts, or the 10 mm up trim for around the body armour . Actual modern companies that sell to the public ???? im not excluding mark or Paul from the discussion, I just would like a source new members/ builders can use to locate their soft goods . id include white soled Chelsea boots in this enquiry, but I’m a realist . Lol . cheers folks.

Keep trooping is the new name for Imperial Boots, they changed it as it's not just boots anymore. I have had mine since wave 4? I think it was, I find them very comfortable, well as far as Chelsea boots are comfortable one me anyway.

Hi all As I understand it, there seem to be some difficulties in finding suitable Boots for Stormtroopers, now that TK boots, most unfortunately, do not have a steady supply (at least thats what I understand). I have compiled a small selection of boots that meet the standards, and at the same time are high quality boots. It puzzles me, that people seem willing to pay only very little for boots. I fully appreciate that we all want to save money, but paying a lot of money for weapons, and not to mention how much we are willing to part with when it comes to lids, armour etc, is no problem. Paying 200$ and more for a pair of boots, on the other hand seems a big deal to a lot of people. The way I see it, boots that are better crafted will last longer, some of them look very much like the originals as well, and they are simply a pleasure to wear. Ihave not trooped much, but I know a lot about marching, and I believe that trooping takes a lot of walking. A lot of walking calls for proper footwear, so why not pay the extra money, and have very high quality, throughout the entire "costume".. ( I see it more as a uniform than costume:-))..from "top to toe" ..? This is the list, all of them meet the standards and will pass for both EIB and Centurion, but none come in white. They all have Goodyear welted leathersoles and they will need a paintjob. Angelus is the thing to use (that is what I used on mine). Loake 290, RRP 160£+shipping, can sometimes be found used on ebay quite cheap, found here: http://www.andersonsofdurham.com/en/mens-shoes/loake-shoes/loake-290.html, WELCOM10 or WELCOME10 is a 10% off code. Or here: http://herringshoes.co.uk/product-info.php?&brandid=7&shoeid=231 Loake Bayswater, RRP 205£+shipping found here: http://www.herringshoes.co.uk/product-info.php?&brandid=7&shoeid=3920 Herring Coltham, RRP 175£+shipping, found here: http://www.herringshoes.co.uk/product-info.php?brandid=6&catid=93&shoeid=3044 John White chelsea boot, RRP169£+shipping, seen on ebay at 89£, found here: http://www.johnwhiteshoes.com/?s=Chelsea&post_type=product Regent Jodphur boots, 96£+shipping, found here: http://shop.horserequisites.co.uk/epages/Gagar.sf/en_GB/?ObjectPath=/Shops/13062006-11837/Products/%22FW0001/6%2B%22 The next ones are Danish Military issue. They are produced by a company in Portugal. I have been talking to the company the last three days, and unfortunately they normally don't sell to private individuals. They look like this: Edit November 2013: Adding two aditional pairs of boots to the list. These are not of the same standards qualitywise, but they are basic CRL cleared, whether or not they will pass for EIB and Centurion I am not aware. Bass Amsterdam chelsea boots, RRP found here: http://www.amazon.com/Bass-Mens-Amsterdam-Ankle-Boot/dp/B003TFEVN0 Or Lands End Fulton chelsea boots, RRP 95$, found here: http://www.landsend.com/products/mens-fulton-chelsea-boots/id_228833 Edit June 2015: Found these referred to in another thread, good looking boots at a fair price, and both EIB and CENT certifiable: http://www.amazon.co.uk/Roamers-Chelsea-Jodhpur-Riding-Leather/dp/B00P940A7U

Hi Robert, You're right about the boot, Unfortunately, the screen used ones were Chelsea boots painted white, but as per the CRL for basic approval they must have a flat sole and a short(er) heel and no logos. Most troopers choose tu buy Imperial Boots https://www.imperialboots.com/ , in my case I went for a local shoemaker.

Hello All! I hope I am posting this in the right area, I am new to Whitearmor - I've been having trouble finding TK boots small enough to fit my size 6 feet, but I managed to find a pair of women's chelsea boots that are white on white while still having a black bottom. They are over $100 so I was looking for some input on whether or not they could be approved at Centurion level before I invest in them. I am mainly worried about the height of the heel as it might be too big. It's really hard to find chelsea boots that have small heels! This is what I found: https://www.everlane.com/products/womens-modern-utility-chelsea-boot-white-leather?locale=US&utm_medium=cpc&utm_source=pla-google&utm_campaign=838139507&utm_content=471192536556&utm_term=pla-973068508291&adgroup=116150501492&pid=8333-61669&device=c&gclid=EAIaIQobChMI2JnsjOKr8QIV9Ql9Ch00ww6wEAQYBCABEgKoVPD_BwE Thank you! - Crystal LordOfTheSWFans