gmrhodes13

Looking good there trooper, best of luck

Biceps should come down a bit, the centre button on your belt looks to be rectangle, hope it's just the photo, also the belt is too long and side button covers too far out, drop boxes should be closer to the end of belt, no black stripe on ear, also a weird looking recess on the side of your sniper plate may need to trim a little off, belt corners are a little small, also the radius on your battery pack on shin too small also it's too high up on leg, should be on the bottom edge. Wouldnt hurt to paint your ab rivets. Oh and another action shot too. With a few small mods you will have an amazing build. Well done and good luck

I found his in a review but it doesn't work on mine, "The time and displayed alarm time can be changed from standard to military time simply by pressing the Time Set button. Each time it is pressed, you will hear a beep and it will switch to the opposite format." I think it may have been an option before production and for some reason it did not end up incorporated in the finished product

Congrats and well done trooper

Of course I put my instructions in a safe place I have been playing with mine for the last 20 minutes, do you think I can change to 24hr clock, no sorry can't help Let me know if you figure it out

The straps do stick out, wouldn't take much to trim them. Just noticed your knee ammo strap could do with a slightly larger radius on the ends, spray can size. Good luck with approval

Also try to give the end of the lines a rounded look, more like a brush would do, keep up the good work

Some nice leather work there, well done

Which ever colour you would still have to paint with silver first. I allready have two E-11's but I may have be purchasing one of these

Dare I say it, tube stripes are way way down on the cheeks, good luck with approval

A very nice and clean application, would just say the screws ont he TD need to be flat head and tapered, also looks like you may have trimmed a bit too much off your belt, can just see he recess section on thee left side. You may not have to do anything about them, good luck with approval

What make is the helmet, I have ata and there was no difference, was this helmet from a maker or ebay. Polish may work, maybe try a bit on he inside, worst synario you will have to paint both pieces.

Your welcome

That looks so much better, well done, you have a much steadier hand than mine

You can really see how big the right arm was in this application, he managed to trim more off and it was such a better look

I have ata but seems a similar problem with right arms, if you think of the cover strips being the tops and bottom, you heat the sides and press them together, makes the large round hole next to your elbow narrower and more oval, hope that makes sense.

If you compare my arms you will see they fit my frame a little better. I have checked your photo again and you seem to have alot of ridge showing next to your cover strip, if you look below you will notice my ridge is only just showing, hope this is a help

Beat me too it http://www.whitearmor.net/forum/topic/14806-how-to-assembling-ata-abs-helmet-1/page__hl__%20pandatrooper%20%20helmet Forearms seem wide, right is usally the worst, I had the same problem, instead of taking it apart I heated both sides and applied some heat, was enough to make the forearm a little more like the lefts side, more oval and less gap

Bell looks fine in that photo, just wasn't sure if you had it attached in your previous one. As long as you satisfy the DO then you will be right, good luck with the painting, it's worth a try, I have seen some other examples and you don't need to do much to make them look brushed

Ok some may say this is a basic one but I and a few others have been caught with the wrong placement of the tube stripes. I was using Dave M decals, some choose to hand paint, I do not have steady enough hands. This was my first attempt: And this is how they should be applied, pencil thickness is ideal. As I said it is a basic one but hopefully it will save people from having to re-paint or re-order and wait for decals to arrive.

Mainly just the helmet, 3 screws on ears (can only see the top ones), can't qutie see your S trim, tube stripes distance school pencil from cheek but DO has not mentioned these so you may be ok. To fix your decals you could try just painting on the lines to give the desired effect, they make a good guide. Keep up the good work trooper

Glen Rhodes 85421 Centurion A4 Thank you again in advance

Don't get me wrong your build is going great, would like to see more guys trying to acheive EIB and Centruion. If you are happy with how you are going then that's all that matters. Well done keep up the good work

Only 8 more to go, cmon guys get building

Congrats trooper the long wait was worth it after all, now get that centurion application started