I'm Batman[501st] Posted March 24, 2014 Report Share Posted March 24, 2014 So, I'm getting ready for actual putting together of the armor and have started getting my snaps ready. My first thought was to attach the snaps to ABS pieces and glue them to the amor. This seems fairly common. But the snap is a fraction of a mm proud of the ABS so will hit the armor. Too keep the metal snap away I thought I would heat and bend the ABS plate. Washer underneath, Heat Push down with custom 'pusher downer' It worked but now the snap spins in the ABS plate. I've obviously flattened the ABS section close to the hole. Will that be a problem if the snap spins when it's in the armor? Or should I attach a seconday plate to raise the snap up? (Sorry for heap of pics) Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted March 24, 2014 Report Share Posted March 24, 2014 Either works fine, I used the top method and have not had a problem. Try to keep glue away from the snaps as sometimes they can heat up and distort your armor Quote Link to comment Share on other sites More sharing options...
I'm Batman[501st] Posted March 24, 2014 Author Report Share Posted March 24, 2014 Thanks. Maybe I could give the snap another whack with the hammer. That might tighten it up a bit again. Quote Link to comment Share on other sites More sharing options...
Cantina Security[501st] Posted March 24, 2014 Report Share Posted March 24, 2014 The spinning will not affect performance . Quote Link to comment Share on other sites More sharing options...
Kadows Posted March 24, 2014 Report Share Posted March 24, 2014 Can anyone explain the benefits of doing these snap plates as opposed to gluing piece of nylon wrapping straight on to the armor? I tried it on a piece of ABS and had no problem. I even put on extra much E6000 to see if it would warp or anything. Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted March 24, 2014 Report Share Posted March 24, 2014 There is no benefit. Sent from my Nexus 5 using Tapatalk Quote Link to comment Share on other sites More sharing options...
maxsteele[TK] Posted March 24, 2014 Report Share Posted March 24, 2014 What about putting a piece of painter's tape on the side of the snap that touches the ABS? Would that be sufficient enough to keep glue away from it and keep the snap from touching the ABS itself? Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted March 24, 2014 Report Share Posted March 24, 2014 I don't buy in to this E-6000 melts plastic when touching metal. Only Vern has said it does and he never showed any proof of it. I or no one else I remember has seen it. It been debated to length before. In other words, keep calm and finish your armour. 1 Quote Link to comment Share on other sites More sharing options...
The5thHorseman[TK] Posted March 24, 2014 Report Share Posted March 24, 2014 This melting stuff is a myth for me too. I tried (several times) putting e6000 on a snap and then glue it to ABS and had no problem at all. Quote Link to comment Share on other sites More sharing options...
gazmosis[501st] Posted March 24, 2014 Report Share Posted March 24, 2014 I have a verification of truth to this but it was not on ABS it was on HIPS. Perhaps ABS can just withstand more or the plastic has different characteristics that makes it resistant. Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted March 24, 2014 Report Share Posted March 24, 2014 In that case, what kind of snaps did you use Steve? Sent from my Nexus 5 using Tapatalk Quote Link to comment Share on other sites More sharing options...
pandatrooper[TK] Posted March 25, 2014 Report Share Posted March 25, 2014 I still use rivets on my snap plates instead of the ones that come with the snaps. Way more surface area for gluing, just tap the back with a hammer and hammer the inside of the snap / rivet end and it sandwiches tight and the back goes concave, making a flush surface for gluing. I've built several sets of armor this way and never had a failure. Or if your armor has return edges that can take it, use the screen accurate wire brackets / elastic. Quote Link to comment Share on other sites More sharing options...
DroidHunter Posted March 26, 2014 Report Share Posted March 26, 2014 I still use rivets on my snap plates instead of the ones that come with the snaps. Way more surface area for gluing, just tap the back with a hammer and hammer the inside of the snap / rivet end and it sandwiches tight and the back goes concave, making a flush surface for gluing. Do you have a picture of that setup that you can post? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.