TKSpartan

Please take a read to the bottom section of this thread https://www.whitearmor.net/forum/topic/41887-robs-wtf-anh-stunt-build/

Could you post a photo with the tow halves together but by the front please?

Hi Keegan, You can remove all the return edge from the botton and leave aprox. half cm on top. some references

Congratulations !!! Welcome to the ranks and awesome story Trooper.

Buckets off our brother in arms Dan is now joining the higher ranks! Buckets off

Congratulations Trooper !! Welcome to the ranks

Welcome aboard Derek. Congratulations for your approval

Welcome to FISD ! Looking forward for your approval photos !! Good luck

The cut lines looks good to me , for the top return edge, you could leave a little and remove entire of the bottom. Some references for you.

Looking good Brian, you may want to trim a little more that small return edge to follow the ridge line and you're golden.

As Kyle rightly pointed, the forearms opening "big enough to get your wrist through" , you put the globes after not before the armor. Some references to see the proportional. Keep up the good work !

Welcome to FISD future TK. ! Good luck with your project and hope to see you in our ranks in a near future.

@FN1313 Here's the note.

Yes, the Trooper mentioned that is waiting for the end cap to arrive. Thanks

Nice job there Brad. Consider, when assembling the clips that the control panel, "The white control panel raised ribbed pad faces the rear, with the controls/round washer style detail closest to the right end cap." A common issue we have seen is that the control panel faces up or is angled but not enough. Some references

Hi Tyler , and THANKS for your submission for ANH Stunt Expert Infantry! That is an nice and well "trooped" set of armor there, sir, but unfortunately there are some issues you need to correct before we can get started and put that EIB badge under your name. Some of them are from Basic level and others are EIB requirements. Starting from your Helmet, Looking closely at your helmet's right ear, looks like some j=kind of repair was made in some moment cause the surface looks rough and some sanding and polishing would be needed, also you can see a small gap that will need to be applied some abs paste to seal it. Reference Images "CRL Basic: Frown is painted gray and does not leave the teeth area" Easy fix with some paint remover (non acetone) a toothpick or cotton swabs. Reference Images As you can see there are a couple of buttons that need a paint session to make them look the same size . One needs a paint remove and the other a little more blue color. As mentioned by another trooper, please check your TD end caps and general measures , the control panel should be rectangular all around and needs to be rotated a little to face the rear as the CRL states for Basic Level. You will need to change the screws for the correct type as well and paint them black color. "Basic: The white control panel raised ribbed pad faces the rear, with the controls/round washer style detail closest to the right end cap. The total length is approximately 7.50" (190.5mm). End caps are approximately .78" (20mm)in width. L2: Clips shall be attached with slotted type, flat or dome top style screws, and be black (two per clip)." References Looking closely at your Canvas Belt it looks to have an inserted section. Since it needs to be a single piece, I should recommend to replace it . Reference Images Your Sniper Knee needs some more trimming to match the screen references and removing the button return edge will allow to get it close to the shin. Bellow you can see the screen references and some examples of ATA approved EIB Sniper Knee , so yours will match in a great manner. References EIB Approved ATA Armor Sniper Knee Finally I'll need you to please, add an additional photo of your AB/Kidney side rivets like the example bellow. Even though it looks like a lot of work ahead, we are confident that you can do it Trooper.

Congratulations for your BBB DAY!!! Looking forward for your photos.

Congratulations Centurion!

Welcome back to FISD Steve!

Looking good. if you're using E6000 glue, allow 24 -36 hours to dry hard specially for the sniper knee.

Hi Tyler, thank you for applying for EIB. As Glen pointed , please update the photos and the fix to the TD . One of us will be with you asap.

Hi Marek Glad to see your Centurion submission . One of us will be with you as soon as possible. Added to the processing line.

Welcome Adam, research is the clue. post photos, ask all questions you have. we are here to help.