lucnak

Congrats!

Congrats on your EIB!

I agree with Preston that RT-Mod or AM will likely be a better fit for you. To make this fit you, you will need to lengthen the chest to back elastic strap and tighten the chest to ab. You will also need to reposition the shoulder bridges to ensure that they meet the back plate. They could also use some reshaping as well to curve more as they are very straight right now.

We're all still here! Take the time you need and we look forward to seeing your photos! (Yes I just decided to represent everyone else just now hahah)

Congrats on your EIB!

Congrats and welcome, trooper!

Now seeing this approval! Congrats!

Sarah, I believe all the above images and more were all collected right here: https://www.whitearmor.net/forum/topic/41016-billgrams-the-one-stop-shop/

Congrats! Very nice build, lots of those attention to detail mods!

Jameson, you look great and you should be very proud of your build! It was a pleasure to help you! Think you and everyone who has already chimed in has mentioned all potential adjustments you could make. Approval should be no problem!

Yes IB has become the go-to with TK Boots closing shop. I recall seeing recommendations to order a size up.

Looking good! Almost done!

Congrats! Keep in mind you should have your boots when you are sizing your shins!

Looks good for basic! Some small tips/suggestions you could make: Your left shoulder bell has a larger gap from the shoulder bridge. I would tighten up the strap here. Suiting up: make sure your TD is centered and that your shins align at the top (your right one is a little off) Your kidney shim on your left side looks like it is slanted back? You could ensure that this makes a vertical seam, but that would probably be quite a bit of work. Hard to tell in photos, but are the rivets on your knee ammo pack painted white? Only a small part of your shoulder bridges are glued on the chest; I imagine that this is due to how everything fits. Just be careful here as they could easily be damaged. Not sure if you have considered perhaps reinforcing these. Small stuff but some tipe that could help elevate your overall accuracy if you're looking for it! Like I said, should be an easy pass for basic!

Should be easy pass for basic approval! Agreed with the other comments. Also looks like there is still some return edge at the wrist which you could remove not just for comfort, but for accuracy! Not a requirement though.

Congrats on your EIB!

Congrats!

Congrats!

Yeap, ABS paste is probably the best solution to filling these holes! Here's a tutorial:

Is there a mould line for the back that you may not have trimmed yet? There's nothing inherently wrong with the two pieces being so close together. The area around your neck looks like it could be a bit uncomfortable at the chest plate, but only you will be able to tell if it is so. Keep in mind that you will have the neck seal as well, which will pad the area, but also make it even tighter at the same time.

Here are a few comments to be researched with some photo evidence. From: @Harbinger: For L2 Phasma's F-11D should require the removed trigger guard in addition to regular TFA F-11 L2/L3 requirements, if not for basic. @gammax: I am also posting this in TFA Phasma discussion. So the CRL for TFA the upper sabatons(the armor pieces on the boot) are pictured with incorrect placement. the top edge should go under the spats not on top of it. It always looking wrong to me but I just figured it out today. They were displayed wrong in the prop show. Scenes in the TFA shows with it under but also showed with it slightly over. I think they are meant to be placed under like every other set of sabaton I have seen on every other suit of amor. I think that during shooting they had a tendency to pop out of placement because of the method of attachment. Its shown here slightly above and then below the spats. Lastly if you look at the visual dictionary for the force awakens, it shows the sabatons under the spats. Same for the TLJ visual dictionary. So that's my reasoning for why the spats have incorrect placement. ----------- PS all the toys also show the sabotans under.

We do have one in the making! I will take a look and see what I can contribute...I figured there were some specific questions that I could assist with, but happy to poke around and collect from various places! I suppose just getting started, making rubber gaskets required for L3 is in line with the other FOTKs.

Looks right to me!

Congrats on achieving Centurion!

Congrats on Centurion!