Jump to content

My first complette TK armor kit build (ESB TK RS-Props)


Recommended Posts

Hello at all, 

 

some friends with a TK have it now done and push me to an own Stormtrooper armor :smiley-sw013:

In this topic I will share to you my progress and I hope to get some tipps and tricks for my build from our community.

 

thanks a lot and imperial regard,

Pascal

(ID/DS/TI-39701)

Edited by GIZA87
Link to post
Share on other sites
  • 1 month later...
  • 2 weeks later...
1 hour ago, GIZA87 said:

Hi at all,

I have a question to the dimensions of the shoulder armor.

How do I find the right measure for myself? :)

 

 

Hey Pascal

You will find out when you size the bells with the torso, there should idealy be minimal gap (Centurion) between the bells and the chest/back and the top of the bell should be touching the shoulder bridge . When trimming the bells note that the originals were trimmed at a curve and not straight:salute:

 

Pics from Lucas archives for the Court case with SDS.

Original to the left

9FtHBvF.jpg

 

Original to the right

YCipk0c.jpg

 

Just some Trooper-motivation:smiley-sw013:

bTAc4YR.jpg

 

 

  • Like 2
Link to post
Share on other sites
  • 2 weeks later...

Hello at all,

 

last weekend I had the first complete try on of my TK. I have to finish now the strapping and the shoulder armor.

Here are some pics of my current status.

 

Thanks for your support :salute:

First_try_of_my_Trooper.JPG

  • Like 1
Link to post
Share on other sites

Looking good, just with the sniper plate if you are going for higher level clearance you may need to adjust it slightly, ideally the angle of the top of the sniper plate should follow the angle on top of the shin

 

bp9fqPs.jpg

  • Like 1
Link to post
Share on other sites

Hi at all,

today I have submitted the pictures of my ESB Stunt Trooper.

Also was today the first time that I wearing my TK more than less minutes :smiley-sw013: 

 

Have a nice weekend everyone

TK-39701_front_back.JPG

Link to post
Share on other sites

Very nice work, good luck with approval.

 

Does look like you could pull your forearms up a little, they are quite close to your hand plates and you do have a large gap at the elbows.

 

With the butt plate sticking outwards you could try adding a piece of bent ABS behind, if you glue it to the butt section then the other side sits against the kidney and stops the butt pushing out.

 

SrvPSl3.jpg

 

Once again good luck

  • Like 1
Link to post
Share on other sites
1 hour ago, gmrhodes13 said:

Very nice work, good luck with approval.

 

Does look like you could pull your forearms up a little, they are quite close to your hand plates and you do have a large gap at the elbows.

 

With the butt plate sticking outwards you could try adding a piece of bent ABS behind, if you glue it to the butt section then the other side sits against the kidney and stops the butt pushing out.

 

SrvPSl3.jpg

 

Once again good luck

It’s a great idea. Thanks a lot :salute:

  • Like 1
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...