dashrazor Posted September 2, 2011 Report Share Posted September 2, 2011 i have these pauldron templates in my archives and would like to share them with the community. i did not make them myself but i converted them into JPG format for easy viewing. you will need to print them in sections or on a large format printer to get the correct size for best results use the PDF file DOWNLOAD HERE instructions Templates reference images Quote Link to comment Share on other sites More sharing options...
TK_LEPER Posted September 2, 2011 Report Share Posted September 2, 2011 Kool, thanks for sharing! Quote Link to comment Share on other sites More sharing options...
TK-4510[TK] Posted September 15, 2011 Report Share Posted September 15, 2011 Hilarious!! Thats my pattern Quote Link to comment Share on other sites More sharing options...
TK-2126_MD[TK] Posted September 15, 2011 Report Share Posted September 15, 2011 Hmmm i cant load the PDF page??? will try later and from my work computer tomorrow. Quote Link to comment Share on other sites More sharing options...
TK-4510[TK] Posted September 15, 2011 Report Share Posted September 15, 2011 I think I still have it somewhere. I could re-post. It was made in 2005 Quote Link to comment Share on other sites More sharing options...
PM1967 Posted December 17, 2016 Report Share Posted December 17, 2016 (edited) Hi, Just to make sure I got the size right.. If I print it out the coloured part (orange, white etc) it will be 25cm (9.8") long and 26cm (10.2") on the widest part. Edited December 17, 2016 by PM1967 Quote Link to comment Share on other sites More sharing options...
JFarwell Posted July 3, 2019 Report Share Posted July 3, 2019 Thanks for sharing Quote Link to comment Share on other sites More sharing options...
JFarwell Posted July 3, 2019 Report Share Posted July 3, 2019 I like the black the best. Does it matter?? Which one for TK stormtrooper. Not sand trooper. And is it a rank or for extra cool factor. Thanks Quote Link to comment Share on other sites More sharing options...
BadBatch[501st] Posted July 3, 2019 Report Share Posted July 3, 2019 1 hour ago, JFarwell said: I like the black the best. Does it matter?? Which one for TK stormtrooper. Not sand trooper. And is it a rank or for extra cool factor. Thanks Standard TKs don't actually wear pauldrons, unless you're doing a Rebels TK or an R1 style TK (Jedha patrol) Or a HWT. BTW: Black = Private White = Sgt Orange = Captain Quote Link to comment Share on other sites More sharing options...
JFarwell Posted July 3, 2019 Report Share Posted July 3, 2019 Ok thanks for the heads up much needed lol. Quote Link to comment Share on other sites More sharing options...
FireMist Posted December 17, 2021 Report Share Posted December 17, 2021 (edited) This pattern is great, but a quesiton. The OP only says it is sketched from an origional. There are not any dimensions... As I'm getting ready to cut this fabric for the pauldron..... I'm wondering if I have it scaled correctly. What is the measurement of yours from the neck out to the edge across the top? The OP just says it is traced from an original.... I'll be a Shadowtrooper, BF will be a crimson trooper. I'm 5'8" and my BF is 5'10" so were nearly the same with a top of shoulder measurement of 5.5" Yea, I have broad shoulders and long arms for a girl. Edited December 17, 2021 by FireMist Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted December 17, 2021 Report Share Posted December 17, 2021 4 hours ago, FireMist said: This pattern is great, but a quesiton. The OP only says it is sketched from an origional. There are not any dimensions... As I'm getting ready to cut this fabric for the pauldron..... I'm wondering if I have it scaled correctly. What is the measurement of yours from the neck out to the edge across the top? The OP just says it is traced from an original.... I'll be a Shadowtrooper, BF will be a crimson trooper. I'm 5'8" and my BF is 5'10" so were nearly the same with a top of shoulder measurement of 5.5" Yea, I have broad shoulders and long arms for a girl. From memory (it was sooooo long ago) I just printed the files as is, made a cardboard template then checked for sizing, I'm pretty sure I added more of a curve to the neck sections as they were a little tight and also increased the length as I found it a little short comparing to references. Quote Link to comment Share on other sites More sharing options...
FireMist Posted December 18, 2021 Report Share Posted December 18, 2021 (edited) 7 hours ago, gmrhodes13 said: From memory (it was sooooo long ago) I just printed the files as is, made a cardboard template then checked for sizing, I'm pretty sure I added more of a curve to the neck sections as they were a little tight and also increased the length as I found it a little short comparing to references. I have a template of paper made, but without my own armor being finished, I really can't check the sizing. As for printing.. Its for a midget if I didn't resize it...LOL. The photos abouve are about 6x10 inches and are not full size. I have the PDF, but the printer only prints a portion of each page. (old printer) Do you remember how much you needed to increase the length? This I suspect is the information I'm going to need. Glad I haven't cut material yet. I redid the pattern to print 100% using paint. (below) I don't know if the server will redact pixels or size... Edited December 18, 2021 by FireMist Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted December 18, 2021 Report Share Posted December 18, 2021 15 hours ago, FireMist said: Do you remember how much you needed to increase the length? This I suspect is the information I'm going to need. Glad I haven't cut material yet. Unfortunately not it was quite some time ago. Pretty sure I printed to fill page. Quote Link to comment Share on other sites More sharing options...
BadBatch[501st] Posted December 23, 2021 Report Share Posted December 23, 2021 On 12/17/2021 at 11:26 PM, FireMist said: Do you remember how much you needed to increase the length? If memory serves I added about 2.25" (~57mm) to the length between the seam line and where the curve starts. When assembled, my pauldrons measure 6" (15.25cm) from the seam to the base of the pauldron. Hope that helps. Quote Link to comment Share on other sites More sharing options...
carcharoth[TK] Posted December 26, 2021 Report Share Posted December 26, 2021 I usually print it in DIN A3 and got perfect results so far. They are the same size as the pauldrons I use for my sandtrooper that where made by trooper1 and his work is awesome. (Crest of the Village I grew up, Swiss Garrison Logo, Crest of the canton I live in) 1 Quote Link to comment Share on other sites More sharing options...
TK-4510[TK] Posted December 26, 2021 Report Share Posted December 26, 2021 (edited) Wow, its still bouncing around I made the template so you could just print it out at 100 percent and it would be correct scale. You may need to shingle pages to make it work. Edited December 26, 2021 by TK-4510 2 Quote Link to comment Share on other sites More sharing options...
Sly11[Admin] Posted December 28, 2021 Report Share Posted December 28, 2021 Hey Mike, How's it going? Quote Link to comment Share on other sites More sharing options...
TK-4510[TK] Posted December 28, 2021 Report Share Posted December 28, 2021 Good! Thanks for asking Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.