TKSpartan

Excellent Chemi. Good luck with your application. Excelente Chemi. Buena suerte con tu aplicación.

Roy : Another suggestion is to remove your left shoulder bell stickers, I have seen this issue for other troopers in some prior EIB request. Cheers

Hi Roy, looking great trooper , mine is an RWA armor too. so cool ! I would like to make some suggestions , According to the CRL, to add the following photos that I'm sure the D.O. Team will ask you for: 1- Close photo :Right and Left ,outside and inside of your Thigh ammo pack to see the rivets type. Level two certification (if applicable): Thigh ammo belt is attached to thigh with a solid head rivet, painted white, in the upper corner and fastened to the lower thigh ridge. The rivets used shall be single cap, double cap or split rivets. No pop rivets allowed. Rivet should be approximately 5/16" (8mm) in diameter (exterior). 2- Close Photo of your Sniper Knee Right and Lef side to see alignment Level two certification (if applicable): Sniper knee plate must be aligned with the ridges on the shin. Sniper knee plate must not have visible rivets or fasteners attaching it to the shin. 3- Close Photo of your boots: Level two certification (if applicable): There is no seam present on the front of the boot. Boots have a black sole 4- Close photo of your ab section to see the ab buttons . A split (bifurcated) or single cap rivet is present on the lower tab (cod area) of the abdomen armor. Rivet does not need to be functional. Rivet on must be brass or silver in color, approximately 5/16" (8mm) in diameter and is not painted. 5- Close photo of your chest to Back plate connection to see the white fabric Chest and back shall be connected with a white fabric or preferably elastic strap at the shoulders. 6- You may want to add some white color to your Hovi tips Correct 'Hovi mic' aerator tips are present. Screens used shall be of a wide type mesh, with the rim of the mic and the inside white or painted white. The D.O team will let you know of any additional photos to submit and corrections if need. Good luck with your approval Cheers

Hi Tom, welcome to the Legion Trooper!! Enjoy being a Bad Guy Doing Good.

Congratulations Trooper. Welcome to the Legion.

Looks good to me too.

Hi Shane, welcome to FISD , looking forward for your building progress, be suro ti open a Building Thread here https://www.whitearmor.net/forum/forum/80-anh-build-threads/ get feedback and tips from our experienced troopers. Post photos, Ask all questions, We are here to help. Another useful resource , if you haven't read yet is the following tutorial about posting photos using Imgur. Good luck with your project.

Great Jonas, now just wait for the D.O. team to start your review. any other photo or adjustment wiil be ask by them Good Luck , Your EIB Badge is waiting for You Trooper !!!

Just in case Jonas. I'm not sure if it's a light ( or my old eyes) effect but the two rivets looks like be in black color? The crl states: Two male snaps are present on the lower center tab of the Posterior Armor. Snaps do not need to be functional. Snaps are silver in color with the bottom of the snap facing outward and are not painted. cheers

Hi Jonas, glad to see your EIB application so soon !!! Great mate. According to the CRL, you may want to add the following photos that i'm sure the D.O. Team will surely ask you for: 1- Close photo :Right and Left ,outside and inside of your Thigh ammo pack to see the rivets type. Level two certification (if applicable): Thigh ammo belt is attached to thigh with a solid head rivet, painted white, in the upper corner and fastened to the lower thigh ridge. The rivets used shall be single cap, double cap or split rivets. No pop rivets allowed. Rivet should be approximately 5/16" (8mm) in diameter (exterior). 2- Close Photo of your Sniper Knee Right and Lef side to see alignment Level two certification (if applicable): Sniper knee plate must be aligned with the ridges on the shin. Sniper knee plate must not have visible rivets or fasteners attaching it to the shin. 3- Close Photo of your boots: Level two certification (if applicable): There is no seam present on the front of the boot. Boots have a black sole 4- Close photo of your ab section to see the ab buttons . A split (bifurcated) or single cap rivet is present on the lower tab (cod area) of the abdomen armor. Rivet does not need to be functional. Rivet on must be brass or silver in color, approximately 5/16" (8mm) in diameter and is not painted. 5- Close photo of your chest to Back plate connection to see the white fabric Chest and back shall be connected with a white fabric or preferably elastic strap at the shoulders. The D.O team will let you know of any additional photos to submit. Good luck with your approval mate!!

Hi Les, You have started with the most challenging part of an armor build, It's at least for me , but I'm sure you're going to do it right . Good luck with your project and keep on posting photos of your progress.

Hi Martyn, your Belt looks amazing and those drop-wallet boxes are such great idea. cool!!!

Here there are a couple of references that i think may be helpful. :

You're right, thanks for the advice.

Don't worry, here they are: from my sight , It looks much better. what do you think? @justjoseph63 @CableGuy

Just move the face plate forward and try to match like the blue lines, for temporary fixing you can use magnets or painter's tape. post some photos for feedback. Cheers

Yes, you're right for the Sand Trooper Crl states Helmet details must be hand painted. Decals, including decals that emulate hand painting, are not allowed. And consider the following details : No vertical black lines in any traps or tears. Frown is painted gray and does not leave the teeth area. Correct Hovi-Mix mic tips. of course that you can check for more details and advices about Sandtrooper at the Mos Eisley Police Dpt Forum. https://www.mepd.net/ Good luck with your project. Cheers

Hi Thomas, looking good but you may want to compare with the reference photo and @CableGuy post reference. I think you can level up a bit the face to align as the reference. This is yours This is reference Hope this can help. cheers

Hi Thomas, welcome to FISD. I would like to recommend you the following Forum Thread, It would be so useful for this challenging part of your project. Be sure to post some photos of your build to receive some feedback before trimming or gluing. This one would help also. Hope this can help. Cheers

Hi Mathew welcome to FISD, you may want to check the following forum section where you can check out the R1 build threads and start your own to recieve feedback and tips for your project. https://www.whitearmor.net/forum/forum/196-rogue-one-build-threads/ Feel free to ask questions , we are here to help . Cheers

Hi, welcome to FISD. You're right, there's no CRL for the Mandalorian's series Flame Trooper yet. As I have read in this forum the rogue one armor is a good starting point. Keep on posting your advances and I'm pretty sure you are going to be receiving some feedback soon from our so experienced fellow troopers here. Again, Welcome and good luck with your project. Cheers

Go ahead trooper !!

Hi, good luck with your project, looking forward to see photos of your BBB day! I think the following forum threads can give you some helpful tips for your helmet build as they were to me. Cheers

Hi, It looks good but think you may want to correct the angles a bit: Hope this can help.

What I would do is to start assembling the helmet to see how things are going , them I could decide where more trimming is needed. Try placing cap and face together and let's see how it looks.