giskard8

Right side details Left side details

Front and Back Right hand side Left hand side

Sorry for the delay. I am working on it and will get the rest up tonight!

Helmet: Front Right Left Back

TK-39093 Requesting ESB Centurion Status [TM] Trooper Info : Name: Arthur Wong FISD Forum Name: giskard8 Legion ID: 39093 Garrison: Hong Kong Garrison Legion Profile: https://www.501st.com/members/displaymemberdetails.php?userID=19986 Height: 5'10" Weight: 176.5 lbs EIB Approval Link : Costume Information : Armor : TM (TrooperMaster) Helmet : TM (TrooperMaster) Neck Seal : Eadu Armory Belt : Mrs. Linguini's Crafts Boots : Imperial Boots Hand Guards : TM (TrooperMaster) Holster : Imperial Boots Blaster : Modified RS Propmasters ESB Promo (Stunt version) Electronics : Dual 12V helmet fans (self installed) / iComm (TK Products) + chest mounted speaker unit Alterations made since EIB granted : Helmet Right Ear repositioned. Helmet Vocoder outline retouched. Hook on both Biceps removed. Ab buttons repainted.  Canvas Belt replaced + button covers trimmed.

Distilled down to pure science!

Congratulations Trina. Welcome to the ranks!

Congratulations trooper. Welcome to EIB!

Hello Mark, 1) Trim it. 2) Not that obvious in your picture. You can try take one picture under sunlight (white light) and another one under warm (yellow) light to see the differences in tone. But since it’s at the back, people don’t usually notice.

Congratulations! Welcome to the ranks.

This is a TD cap from RS prop.

2.5" inner diameter PVC pipe seems fairly common.

Congratulations!

Congratulations! Welcome to EIB.

Congratulations! Welcome to the Legion.

Congratulations Zylo, Welcome to EIB!

Further up, the helmet: OPTIONAL Level three certification (if applicable): Ear bars shall have only one or two bumps painted in black (rank stripes). Neck trim shall be of an s-type profile rather than a u-type profile. Tears/traps shall be hand painted or use decals that emulate hand painted (with correct ANH TK details). Blue stripe continues over brow trim Ear screws shall be slotted, flat topped, countersunk and painted white. The blue strip now covers the brow trim. I also did some minor adjustment to the strip's position and some purely cosmetic touch up on other features. Before (green background) and After:

Working up to the abdomen plate and buttons: OPTIONAL Level three certification (if applicable): There shall be no split rivet or brad visible on the crotch tab of the ab plate. The left vertical row of ab plate buttons contain five buttons (fifth button must align one button higher than the top button of the larger button plate). All buttons on the ab plate are the same size and color and are visible (not covered by the belt). The fifth button is mounted vertically above the standard four buttons.  There are 2 rivets on either side of the ab, approximately 5/16"(8mm) diameter which are lined up with the ones on the kidney. The top rivet is 25mm from the top edge and the bottom is 25mm above the top of the belt and 20mm from the side seam, painted white (measurements are approximate). I have moved the "Left 5-Buttons" plate up a little bit so that the top button now sits slightly above the center plate if you draw a line across the ab. The one thing I did not do comparing to the reference pictures is re-shaping the corner of kidney plate and the ab plate. My suit was based on a Troopermaster ROTJ kit so the top corner of the kidney plate is rounded (and the whole plate is fused with the butt as one), while the corner on the matching edge of the ab plate is squared. I do not know if any maker do their kits as the game skin reference below (maybe CFO does?), but I guess one can always convert an ANH kit to ROTJ style but keeping the squared top of the kidney and rounded off the top corners of the ab plate.

Starting from the most obvious update from the TKC CRL. The ammo belt on the right thigh, according to the high res images in the following thread: Pre new CRL requirements: OPTIONAL Level three certification (if applicable): The thigh ammo belt shall be positioned on top of the lower ridge as seen in official references and is not rounded off like ANH. The thigh ammo is glued and has no rivets. Save myself from buying a new knee ammo belt, I opt to trim it down as marked in the following picture. I left the return edges on top and bottom untouched, but according to reference they should be flush (?). I might go back and work on them later but at this moment I would like to see the overall effect first before I decide if they needed to be trimmed further. Temporarily fixing it to position and check. Filled the hole for the original rivets with some white model putty. Didn't bother with ABS pasting since the blue paint and the weathering will cover them up, more or less. Acceptable, do you think? After painted over. Glued down with E6000 One thing: the size of the knee ammo belt in the reference skin seems a bit small compare to what is available with most TK kit sets (in my case Troopermaster). I have compared it with MTK, Anovos and RS Propsmaster they are all about the same size, more or less. If someone is bend on making it look exactly like the references, one might have to create his very own to match.

Looking sharp! Congratulations ~

Congratulations! Welcome to EIB.

Hello and welcome to the FISD!

Congratulations and welcome!

Welcome to FISD.

Congratulations on making Centurion!