Stormy1992

Also the shoulder straps! i use two per side it keeps them from rolling around. i highly recommend that you do the same.

Just looked over your thread and it looks good to me so far! i used cap rivets to attach the belt. one side - belt - ammo packs - other side then hammer I got mine at hobby lobby. a pack of like 200 haha couldnt get them any smaller. Also, the Bottom of the ears look a little big. may want to trim them down a bit. (wont hold up application but its more screen accurate)

Thank you!!

Kyle Morrow 33092 EIB Letter

Thank you so much for passing me and the kind words! the back seam of the thigh i could close down a little more if i cut the ridge off.. make sense to me. there isnt a huge gap, but it could be taken in! Thank you thank you!! i will take the steps to submit to centurion too! thanks! WOOHOO!

Yuuuuup:) you can call me Kyle if yah want!

Do you have the thighs right? its hard to tell from the pictures being small. it MAY seem you have the insides and outsides swapped from looking at the back side. But great on the holster and neck seal!

I had the same question with the depth in my eyes also.. its hard to say.. if there is any to what seems to be line then cut it if not then dont make it too close to the edge of the eye it looks pretty good from here.. ill find a pic for you. this is the closest one that i could find.. in the right eye (waht youre seeing to your left) the very inside of the eye is probably 5-10mm deep. and on the other eye on the outerside of the helmet is 10mm or so deep too. just try to see from this image depth. every helmet is different but you should be able to tell The helmet builds are the hardest part but most fun and challenging. good luck and take your time ESPECIALLY with the ears...

Thank you!! Just put 3 coats of clear over it! But wonderful I shall wait for you!!

Your welcome! If you need anything else as far as images and advice are concerned just ask!

Thank you for the replys! I'll bring the bells closer and also the drop boxes and 2mm from the belt hard to bring them closer haha I could see the shins however the thighs are turned a little maybe. Not off by too much? It would be hard to bring them in how I made my cuts. It'll also make me look a lot smaller but I'll look into it! How does this all work anyway?

Name: Kyle Morrow FISD: Stormy1992 Garrison: Bloodfin Armor Maker: Scootch's CAP Armor Hand Guards: Scootch's CAP Armor Helment Maker: Scootch's CAP Armor Blaster Type: Hasbro Doopiedoos Covered (soon to receive/build Doopiedooes E-11) Height: 5'11 Weight: 130lbs Canvas Belt: TKittle Boots: Black ambassadors painted white Electronics: Icomm Anker system. Without further or do here we are! Front: Back: (note!: I was leaning on me left leg giving my right leg a bend 'in case the legs dont look even') Right side Arm up! Left: Arm Up! Detail Dropbox attachment Bucket; Front: Right: Back: Left: Detail: Inside; Blaster; Right: Left: D-ring; NeckSeal; Gloves: Action Shots: Just for fun: Thank You All for looking! -Kyle

also when you go to put on your knee ammo pack.. just be careful when lining them up. like this: I was told to go a little higher than this so bend it up to cover the split (if you have one) if not youre okay just wanted to show how far back it goes on both sides. the cuts look great on your build though

i sliced my thumb open too. i think everyone does once in there build haha! the sniper plate was tricky but after being done it wasnt too hard. just line up the groves and glue. i didnt use rivets. hopes this helps!

from the small images it looks to be good try using photobucket to post them bigger

Thanks guys!

Yes this is the CAP suit i own off ebay from Scootch.. and needless to say. im in love. really really wonderful!

this is very cool! excited to see these come out!!!

I was thinking to add some fabric.. however where would you attach it to? looking at the seal its hard.. i was even thinking about getting a sleeveless compression to wear over it

Tk33092 here, I have one issue with my suit. I was given an underarmor shirt from my brother which was awesome, however it has a big logo on the very back of the neck. figuring my neck seal would cover it, it does not. Is there any mod or way to add fabric to the neck seal to have it cover the back? it is a standard seal with the fabric that wraps nicely around the front, however no flap of fabric to cover the neck. common problem? tips, hints? thanks!

Looks great and alot of product that i went with. the belt is wonderful! neck seal is too. i need to find a way to wrap the material around to the back.. didnt have a back piece. maybe i can make a question thread about it. anyway looks all good man! i may look into some TK boots for myself also.

Thank You Sir!

Looks good brother!!

asking for 501st permissions TK33092 http://www.501st.com/members/displaymemberdetails.php?userID=17290