Lionel Noronha Gallardo[TK] Posted September 26, 2018 Report Share Posted September 26, 2018 Hi guys Any tips to avoid the dreaded coupling. I have an Aker in my chest armor ,and a wireless mic in my helmet and it seems i cannot avoid getting coupling? Cheers Quote Link to comment Share on other sites More sharing options...
McWinsch[TK] Posted January 23, 2019 Report Share Posted January 23, 2019 Following...I have the same issue. Quote Link to comment Share on other sites More sharing options...
sharkbait[TK] Posted January 24, 2019 Report Share Posted January 24, 2019 You mean feedback, or not connecting? Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted January 25, 2019 Report Share Posted January 25, 2019 You will find even with direct cable to aker you will get feedback if the volume is too high, have you tried testing at a lower volume and then turning up slowly to find when the feedback starts or are you getting feedback straight away at any level? Quote Link to comment Share on other sites More sharing options...
sylverbard[TK] Posted January 26, 2019 Report Share Posted January 26, 2019 if the wireless mic is at your mouth it is less of an issue. if its attached to the bucket and a few CM away, you need to turn it up to be useful, which echoes and causes feedback from the aker as well if it is too loud. even my wired aker mic hums a bit if i have the amp turned up too loud. and its in my chest plate less than a foot from my mic: 99% of the time it doesn't cause any feedback. Quote Link to comment Share on other sites More sharing options...
Lionel Noronha Gallardo[TK] Posted February 24, 2019 Author Report Share Posted February 24, 2019 I found a solution to coupling which cost none to nothing. Cut a square piece a Eva rubber and place it inside the helmet where your mic sits ( this will muffle 99% the sound coming out the helmet ) mine is 2 by 2 inches. For extra sealment i cover the mic foam leaving the mic area free. I have tested this and it works Good luck Quote Link to comment Share on other sites More sharing options...
Frank75139[501st] Posted February 25, 2019 Report Share Posted February 25, 2019 I found a solution to coupling which cost none to nothing. Cut a square piece a Eva rubber and place it inside the helmet where your mic sits ( this will muffle 99% the sound coming out the helmet ) mine is 2 by 2 inches. For extra sealment i cover the mic foam leaving the mic area free. I have tested this and it works Good luckAny chance we can get a pic?Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
KOtrooper[501st] Posted March 1, 2019 Report Share Posted March 1, 2019 On 2/24/2019 at 10:00 AM, Lionel Noronha Gallardo said: I found a solution to coupling which cost none to nothing. Cut a square piece a Eva rubber and place it inside the helmet where your mic sits ( this will muffle 99% the sound coming out the helmet ) mine is 2 by 2 inches. For extra sealment i cover the mic foam leaving the mic area free. I have tested this and it works Good luck I'm having the same issue that I'm trying to fix. Could you post a pic or diagram? Quote Link to comment Share on other sites More sharing options...
Lionel Noronha Gallardo[TK] Posted March 9, 2019 Author Report Share Posted March 9, 2019 (edited) On 3/1/2019 at 11:44 PM, KOtrooper said: I'm having the same issue that I'm trying to fix. Could you post a pic or diagram? No worries buddy. I am not currently at home but will do next week Edited March 9, 2019 by Lionel Noronha Gallardo mistake Quote Link to comment Share on other sites More sharing options...
Lionel Noronha Gallardo[TK] Posted March 9, 2019 Author Report Share Posted March 9, 2019 On 2/25/2019 at 12:21 AM, Frank75139 said: Any chance we can get a pic? Sent from my iPhone using Tapatalk Yes buddy. next week I will upload a pic. Not at home for a few days 1 Quote Link to comment Share on other sites More sharing options...
Lionel Noronha Gallardo[TK] Posted March 12, 2019 Author Report Share Posted March 12, 2019 (edited) here it is guys -------- As mentioned before, cut a piece of Eve rubber and place it as shown the pic. For extra isolation you can also cover your mic head with Eve rubber leaving an opening for your voice to go through . l Edited April 5, 2022 by gmrhodes13 link removed no longer working Quote Link to comment Share on other sites More sharing options...
Frank75139[501st] Posted March 12, 2019 Report Share Posted March 12, 2019 (edited) On 3/12/2019 at 4:31 PM, Lionel Noronha Gallardo said: here it is guys ------------- As mentioned before, cut a piece of Eve rubber and place it as shown the pic. For extra isolation you can also cover your mic head with Eve rubber leaving an opening for your voice to go through . l Is eve rubber a brand name? Sent from my iPhone using Tapatalk Edited April 5, 2022 by gmrhodes13 link removed no longer working Quote Link to comment Share on other sites More sharing options...
Lionel Noronha Gallardo[TK] Posted March 13, 2019 Author Report Share Posted March 13, 2019 (edited) here it is guys --------- As mentioned before, cut a piece of Eve rubber and place it as shown the pic. For extra isolation you can also cover your mic head with Eve rubber leaving an opening for your voice to go through . l Yes. It is type of soft rubber that you can find in any craft shops. Kids use it at school. I ma not sure if in the States is named the same. Here in Spain is called Goma Eva Edited April 5, 2022 by gmrhodes13 link removed no longer working Quote Link to comment Share on other sites More sharing options...
Lionel Noronha Gallardo[TK] Posted March 13, 2019 Author Report Share Posted March 13, 2019 Yes. It is type of soft rubber that you can find in any craft shops. Kids use it at school. I ma not sure if in the States is named the same. Here in Spain is called Goma Eva Quote Link to comment Share on other sites More sharing options...
Lionel Noronha Gallardo[TK] Posted March 13, 2019 Author Report Share Posted March 13, 2019 It is Ethylene Vinyl Acetate known as EVA rubber (sorry not EVE). They are craft foam sheets Hope this clarification helps 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.