SgtGarand[TK] Posted October 28, 2017 Report Share Posted October 28, 2017 General Information Name: Asa Pittman FISD Name: SgtGarand Legion ID#: 83042 Garrison: Japanese Garrison (Member Page) Mandatory Information Armor Maker: NE (Build) Helmet Maker: ATA Blaster Type: Blaster Master (Build) Additional Information Height: 5' 10" Weight: 203 lbs Canvas Belt: Imperial Issue Electronics: iComm and Aker amp Centurion Level Rivets and Screws: justjoseph63 Full Body Front: Left: Back: Right: Right Detail: Left Detail: Action Shot: Armor Details Abdomen Detail: Rivets: Corner Snap: Cod and Butt Plate: Interior Strapping: Shoulders: Left and Right Forearm: Sniper Knee: Shin armor back: Knee Ammo Pack: Helmet Details Front: Left: Back: Right: Hovi Tip: Lens: S-Trim: Blaster Details Left: Right: Folding Stock: D-Ring: Accessory Details Neck Seal: Thermal Detonator: Holster Attachment: Boots: Belt: Gloves: 1 Quote Link to comment Share on other sites More sharing options...
magni[TK] Posted October 28, 2017 Report Share Posted October 28, 2017 Overall you look good! One thing though, it looks like you have the coverstrips on the back of your shins on the inside. They should be on outer side of calf. Besides that Good Luck! 1 Quote Link to comment Share on other sites More sharing options...
SgtGarand[TK] Posted November 1, 2017 Author Report Share Posted November 1, 2017 Updated with pic of the corrected shin cover strips Quote Link to comment Share on other sites More sharing options...
Sly11[Admin] Posted November 4, 2017 Report Share Posted November 4, 2017 Very nice indeed, we shall be with you shortly Asa Quote Link to comment Share on other sites More sharing options...
Sly11[Admin] Posted November 6, 2017 Report Share Posted November 6, 2017 Hi Asa I am in the midst's of your application review and we have found something that we would like you to change. It falls into the level 2 CRL so will be a requirement to pass EIB For level two certification (if applicable): There shall be three square buttons, one centered in the middle and one on each end of the plastic ammo belt.. It appears that your 3 buttons are in fact rectangular and not square, so we will require some of the extra material to be trimmed off. Hopefully these are glued on with E6000 so the task is quick and simple. Quote Link to comment Share on other sites More sharing options...
SgtGarand[TK] Posted November 7, 2017 Author Report Share Posted November 7, 2017 (edited) 23 hours ago, Sly11 said: Hi Asa I am in the midst's of your application review and we have found something that we would like you to change. It falls into the level 2 CRL so will be a requirement to pass EIB For level two certification (if applicable): There shall be three square buttons, one centered in the middle and one on each end of the plastic ammo belt.. It appears that your 3 buttons are in fact rectangular and not square, so we will require some of the extra material to be trimmed off. Hopefully these are glued on with E6000 so the task is quick and simple. Yes, E6000 made them easy enough to remove. Measured out the distance on the shorter sides and cut from the longer to match and gave the edges a quick sand and glued them back into place. Edited November 7, 2017 by SgtGarand 1 Quote Link to comment Share on other sites More sharing options...
Sly11[Admin] Posted November 8, 2017 Report Share Posted November 8, 2017 Hey Asa Thank you for your EI application lets see what we have. CRL and EIB Application Requirements: All submission photos have been posted. Your armor displays all the necessary elements to qualify for Expert Infantry. Welcome to the rank trooper! Other-Armor Fit/Assembly: In this section we review observations made by your fellow troopers and ourselves. Some observations may lead to suggestions to improve the overall look of your armor. If any suggestion affects any application, it will be listed separately in the above or below sections. There are only a few things to cover here, all very easy to fix. The first item is a common change that we request many applicants make, and it is to bring in the top of those shoulder bells so they virtually touch the plastic shoulder bridges. Your bells could also do with a slight rotation forward to reduce the overall gap between than and the chest plate Screen reference The gap between Bicep bottom and the top of the fore arms can be reduced if you drop the biceps and raise the fore arms. Its only a small amount each but it will even out the gaps so you are in balance. Reference We also noticed you have plenty of return edge on some of the pieces that could be trimmed down a touch. This has no bearing on your application more a comfort thing that also allows a bit more flex in the armour pieces. The top of the Ab plate looks like it could stick into you or damaged your under suit so reducing that return might prevent that. Centurion Suggestions:In this section we prepare you the best we can for Centurion. You have supplied a few extra images that always help us make better decisions when appraising armour builds, so thank you for those. I cant see anything that would hinder a successful Centurion application, so make a few minor adjustments make sure you have all required photos submitted and get that Centurion application in. Congratulations Trooper, head on out Quote Link to comment Share on other sites More sharing options...
Shanester[TK] Posted November 8, 2017 Report Share Posted November 8, 2017 Congratulations and welcome to EIB trooper! 1 Quote Link to comment Share on other sites More sharing options...
SgtGarand[TK] Posted November 8, 2017 Author Report Share Posted November 8, 2017 Awesome news to see before another long work day! Thank you! I've already been trying to adjust the strapping in the arms to fix the gaps and added some padding in the forearms to keep them in place. I'll work on trimming the return edges this weekend and put in my application. Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted November 8, 2017 Report Share Posted November 8, 2017 Congratulations and welcome to the ranks trooper 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.