snipedoc2001
501st Stormtrooper[TK]-
Posts
41 -
Joined
-
Last visited
About snipedoc2001
Member Title
-
Position
Expert Infantry
Profile Information
-
Gender
Male
-
Location
Colorado
FISD Info
-
EIB Awards
1
-
EIB Cohorts
ANH-S
Standard Info
-
Name
Cody
-
501st ID
51550
-
501st Unit
Mountain Garrison
Recent Profile Visitors
601 profile views
-
My first ANH TK Build-Assistance Welcome! (ATA)
snipedoc2001 replied to Phat Rob's topic in ANH Build Threads
I have attached some pics of my shoulder straps, and I am approved at EIB as of now, few small touch ups to get to Centurion, but that's not the point. I was only able to attach the large tab and about half of one of the small ones due to the odd shape of the ATA chest plate and still made it to the higher levels. Correct me if I am wrong, but its more about fit and being proportionate to accuracy: I left the back tabs on as the ATA straps are shorter than some of the other makers are so definitely test fit before you make any cuts. It's much easier to cut something off than to put it back on, however not impossible to fix, it just sucks. Hope this helps! -
Newb starting first build
snipedoc2001 replied to Maelzer's topic in Getting Started - Read this First!
Hey Marc, great seeing you over here. Tons and tons of great people and build threads are available for you. Look at all of the pinned threads located here https://www.whitearmor.net/forum/forum/38-getting-started-read-this-first/ Feel free to PM me if there are any questions! -
First off, excellent build! A few small suggestions that I have would be make sure that your chest plate overlaps the ab plate. Make the shoulder straps a bit longer. Your back plate should be just barely touching the top of the kidney plate. Another thing is that the brow rubber needs to extend to the end of the trap. Another thing would be to raise your belt higher so I just touches or overlaps the ab button plate Last thing would be for higher levels (doable and recommended), the drop boxes need to line up with the outside of the plastic belt Here is mine for reference Other than that, great build and good luck with approval!
-
Congratulations man! ATA is an excellent kit, that is the set that I have. Has great potential. Be sure to post pics and ask a lot of questions! Good Luck and have fun!!
-
Request your EIB Certificate here:
snipedoc2001 replied to justjoseph63's topic in Request Expert Infantry Status
1. Cody Elder 2. 51550 3. EIB 4. Letter 5. Joseph http://www.whitearmor.net/eib/certificates/51550-eib.png 277 -
snipedoc2001 started following TK 51550 REQUESTING ANH STUNT_EIB STATUS (ATA) (958) and ATA Helmet Build/ Armor
-
Congratulations! Been following your build for a bit. Good luck on your approval pics. Looks great!
-
Done. Thanks for the assist @TKSpartan 1- Close photo :Right and Left ,outside and inside of your Thigh ammo pack to see the rivets type. 2- Close Photo of your Sniper Knee Right and Left side to see alignment 3- Close Photo of your boots: 4- Close photo of your ab section to see the ab buttons and Han rivet. 5- Close photo of your chest to Back plate connection to see the white fabric 6- Photo of your internal Straping
-
Mandatory Information Armor = ATA Helmet= ATA Blaster= RUBIES CONVERSION Optional Height = 1.7m Weight = 65 kg Boots = DIY Canvas belt = Trooperbay Hand Plates = ATA Electronics= TrooperTalk Neck Seal = DIY Holster = DIY Full body Front Full body back Full body without bucket Full right Full Left Right side detail Left side detail Helmet details Helmet front Helmet side Helmet back Hovi tip detail Helmet lens Accessories Ammo belt Neck seal Blaster left side Blaster right side Blaster back Thermal det Thigh Rivets Action Shot Thank you all for the support and I look forward to working with the DOs' -- Regards, TK-51550 Cody
-
The best thing to do in this case is a hot water bath and carefully mold the calf armor closed and the Velcro is less likely to pull apart. Check out this thread and ask questions before doing anything. If you close that gap at the top of the calf armor, you should be golden.
-
HeeM requesting pre approval review (rs)
snipedoc2001 replied to HeeM_SeNsEi's topic in Build Threads Requireing Maintenance
No problem! That's what we are here for. Looking at the CRL again, it says "Mesh may be used behind the frown to obscure the face of the wearer.", so it looks like it is not required for basic, but it will definitely enhance your kit. I would be more than happy to help you out with the straps if you'd like, just PM me. -
HeeM requesting pre approval review (rs)
snipedoc2001 replied to HeeM_SeNsEi's topic in Build Threads Requireing Maintenance
It looks great. Few things I would like to address: Make sure the sniper knee sits on the outside of the thigh armor. Most likely a fitting issue. You could also add some upholstery foam behind the sniper plate. Does your helmet teeth have mesh behind it? There should be a black elastic band the wraps the inside of the shoulder bells around the bicep and the biceps need to sit just a little bit higher. As well as the forearms can sit a little higher so they don't overlap the hand plates. Looks excellent for basic and could go higher with jut a few tweaks on the straps. -
Great work so far mate. Lookin good. To answer your question, my understanding is that the cover strips don't necessarily have to track down the middle but the strips on the thighs need to line up with the coverstrips on the shins. The reference photo on the CRL on the website shows the thighs slightly off center, but perfectly lined up with the shins. Keep up the good work!