paulting[TK] Posted February 4, 2012 Report Share Posted February 4, 2012 TK5863 Requesting for AHN Stunts EIB Status Armor= ATA Helmet= ATA Blaster= Hasbro with Doopydoos Kit Height = 176cm Weight = 90kg Boots = TK boot Canvas belt = DIY Hand Plates = DIY Glove = black rubber glove Electronics= None Neck Seal = DIY Holster = DIY tell me if i am missing something else or need to improved Quote Link to comment Share on other sites More sharing options...
BananoPower22[TK] Posted February 4, 2012 Report Share Posted February 4, 2012 looking good but you can definitely do something about the thighs.. they look way too low Quote Link to comment Share on other sites More sharing options...
Trooper1972 Posted February 4, 2012 Report Share Posted February 4, 2012 looking good but you can definitely do something about the thighs.. they look way too low I agree because your sniper plate is fowling the thigh and tucked up behind it Quote Link to comment Share on other sites More sharing options...
Star Raider[TK] Posted February 4, 2012 Report Share Posted February 4, 2012 (edited) Your Thermal Detonator needs to have 1 inch metal clips, they must be metal and can't be painted silver. (According to CRL) Before trimming your thighs, trying decreasing the length of the strap holding them up and just raise them. There should be about an inch gap.. You seem to have like 2-3 inches of space. Try shortening it. That sniper plate needs to be in front as well. Edited February 5, 2012 by Star Raider Quote Link to comment Share on other sites More sharing options...
BananoPower22[TK] Posted February 4, 2012 Report Share Posted February 4, 2012 (edited) Is it just me or are these tube stripes gigantic? Is it just the angle that's making them look like that? I'm kinda confused Edited February 4, 2012 by BananoPower22 Quote Link to comment Share on other sites More sharing options...
captsafe66[Admin] Posted February 4, 2012 Report Share Posted February 4, 2012 Yes, the tube stripes look too large. Do shorten your thigh straps, should be good then. Mason will need more pics as well. Add an action pose, shots of both sides, more helmet shots too. Very close though, looks great! Quote Link to comment Share on other sites More sharing options...
firebladejedi[TK] Posted February 4, 2012 Report Share Posted February 4, 2012 I noticed that your ear screws are not painted, the tube stripes are rather large and i would like to see more pics of your hand painted details on the helmet. I would also say the canvas belt is too wise, it should be 3 inches wide. At a guess yours looks over 4, also the plastic ammo belt part is trimmed wrong at the 45' angles. The holster is a little flimsy too and not overly accurate. The td clips need to be metal and spaced further apart for a better look. I think you need to get your member status sorted to 501st too, although i dont know who you need to ping for that. What happened to detailed pictures for applicants? I see you are missing a left side shot, and i would like to see close ups of the chest straps, buttons and other specifics in apllication threads. Quote Link to comment Share on other sites More sharing options...
ObiHahn[TK] Posted February 4, 2012 Report Share Posted February 4, 2012 (edited) Quite frankly, you are way off in quite a lot of details for a serious EIB application... Most were mentioned before, here's what I noticed (compared to the movie costumes and not necessarily EIB guidelines): - waaaaaay to large tube stripes, too few on each side as well (you need more like 13-16 on each side) - ear screws not whitened - too few detail stripes in the helmet tears (you have only 5 instead of 7) - the whole belt is trimmed and detailed entirely wrong, you should really check a couple references again, and more thoroughly (cloth part should not be wider than plastic front, 45° angled corner cut-offs are too big, too much plastic material left untrimmed next to the rivet cover plates left and right, drop boxes waaaaay too fat, etc.) - your detonator has a "control panel" on it that's too wide and thus not enough grey tube is showing, also your clips are in the wrong position and there should be no tape on them like you seem to have - the holster is quite inaccurate - your thighs look really off in the back, I do see the need to widen them due to your thighs but the cover strips should not be the shims to add material IMHO... I hate to be the one to say it, but this is not yet really EIB worthy. It feels a little too sloppy considering how easy FISD makes it for everyone to research in greater detail and check twice before grabbing x-acto blade and paint brush... Edited February 4, 2012 by ObiHahn Quote Link to comment Share on other sites More sharing options...
paulting[TK] Posted February 5, 2012 Author Report Share Posted February 5, 2012 thanks guys, for pin out out the problem, coz my outpost don't have any EIB yet, hard to get detail with them. i will fix them. i request in the future again. Quote Link to comment Share on other sites More sharing options...
dashrazor Posted February 7, 2012 Report Share Posted February 7, 2012 hi paul its great to see you are on your way to getting EIB! do you ever meet up with any of the guys in the Singapore Garrison? there are a few guys there that im sure could help you out Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.