john danter Posted April 15, 2011 Report Share Posted April 15, 2011 Hello folks! Topic says it all really Is there a special tool to make the legs splay out or do you use a screwdriver or something? Ta John Quote Link to comment Share on other sites More sharing options...
89Batman[TK] Posted April 16, 2011 Report Share Posted April 16, 2011 http://www.ehow.com/how_7878216_install-split-rivets-guitar-case.html Have a look at this mate- it seems you just bend them! Quote Link to comment Share on other sites More sharing options...
john danter Posted April 16, 2011 Author Report Share Posted April 16, 2011 Cheers Gary The ones I have are too strong to be bent with a knife I'm sure I'll try later though John Quote Link to comment Share on other sites More sharing options...
troopermaster Posted April 16, 2011 Report Share Posted April 16, 2011 Do you mean bifurcated rivets? Quote Link to comment Share on other sites More sharing options...
Darth Voorhees[501st] Posted April 19, 2011 Report Share Posted April 19, 2011 Do you mean bifurcated rivets? I think thats what he means. I used a small screwdriver to "open" those types of rivets, although i dont know if mine are thinner and weaker than yours John. Quote Link to comment Share on other sites More sharing options...
tkrestonva[TK] Posted April 19, 2011 Report Share Posted April 19, 2011 I thought you needed a specialized tool use the split / bifurcated rivets. Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted April 19, 2011 Report Share Posted April 19, 2011 I thought you needed a specialized tool use the split / bifurcated rivets. Why? You just need to bend the legs outward. I haven't done this on mine yet, so maybe I shouldn't say anything, but to me it seams really straightforward. Quote Link to comment Share on other sites More sharing options...
Madmartigan Posted April 19, 2011 Report Share Posted April 19, 2011 Why? You just need to bend the legs outward. I haven't done this on mine yet, so maybe I shouldn't say anything, but to me it seams really straightforward. I would think it depends on the thickness of the "legs". I've seen special anvils and special attachments to close them on a press in a couple of sites. One guy hand made something he attached to some vice grips and created his own jury rigged hand press. Other said just use a flat anvil and they should spread properly. Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted April 19, 2011 Report Share Posted April 19, 2011 I would think it depends on the thickness of the "legs". I've seen special anvils and special attachments to close them on a press in a couple of sites. One guy hand made something he attached to some vice grips and created his own jury rigged hand press. Other said just use a flat anvil and they should spread properly. I haven't seen that, so if they have really big industrial strength rivets that might be required. With mine i doubt anything more than a pair of pliers and/or a swiss army knife would be needed. Quote Link to comment Share on other sites More sharing options...
firebladejedi[TK] Posted April 19, 2011 Report Share Posted April 19, 2011 A screwdriver and molegrips should do you alright. Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted April 19, 2011 Report Share Posted April 19, 2011 A screwdriver and molegrips should do you alright. Sounds about right Quote Link to comment Share on other sites More sharing options...
john danter Posted April 19, 2011 Author Report Share Posted April 19, 2011 I'll give it go Yes, bifurcated rivets. My legs are quite thick and would take a lot of force to splay flat I think mine are meant to curve and not go totally flat...? The legs do travel upto about 2mm from the head mind, so they should splay ok I guess Quote Link to comment Share on other sites More sharing options...
troopermaster Posted April 19, 2011 Report Share Posted April 19, 2011 They come in various styles and the ones I have are tough SOB's. I use a thin chisel to start getting the legs spread, then use a hammer to flatten them against my vice. It can get very tricky in certain areas so be careful you don't damage any plastic if you try my method. I've since found some nice brass brads which have the same head size as the bifurcated rivets and I am using them from now on. Anyone else who is (or wants to) use brads, make sure you cut off the excess length of the legs so they don't protrude past the edge of the washers Quote Link to comment Share on other sites More sharing options...
john danter Posted April 20, 2011 Author Report Share Posted April 20, 2011 Ok thanks lads Sounds like brute force is the way. I was hoping someone would say you need a 'bifurictional splay tool thingie, £7.99 from odd tool supplier' Hammer and chisel it is lol Quote Link to comment Share on other sites More sharing options...
R2Dan[TK] Posted April 20, 2011 Report Share Posted April 20, 2011 (edited) Here's another idea: Take split rivet in your right hand. Open window. Throw the split rivet up in front of you. Switch on handheld fan in your left hand. Hold fan so the rivet will be hit by the air flow when it comes back down (timing and coordination is tricky, I know) Watch how the rivet gets fanned out the window! Here's an illustration: ---------- Then go get some brads and bend them using your fingers Edited December 10, 2020 by gmrhodes13 link not working, removed gmrhodes13 2020 Quote Link to comment Share on other sites More sharing options...
firebladejedi[TK] Posted April 20, 2011 Report Share Posted April 20, 2011 (edited) On 4/20/2011 at 11:01 PM, R2Dan said: Here's another idea: Take split rivet in your right hand. Open window. Throw the split rivet up in front of you. Switch on handheld fan in your left hand. Hold fan so the rivet will by hit be the air flow when it comes back down (timing and coordination is tricky, I know) Watch how the rivet gets fanned out the window! Here's an illustration: ------ Then go get some brads and bend them using your fingers Edited December 10, 2020 by gmrhodes13 link not working, removed gmrhodes13 2020 Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted April 20, 2011 Report Share Posted April 20, 2011 I just did my split rivets and did as Mark said and used a screwdriver and a pair of pliers. I used the round "rod" of the screwdriver in between the rivet legs pushing it down with the pliers to spread the legs just so much that they hold the washer in place. Then I only used the pliers to bend the legs down completely over the washer. Quote Link to comment Share on other sites More sharing options...
john danter Posted April 20, 2011 Author Report Share Posted April 20, 2011 I tried the fan/window idea, thanks. Thing is the rivet was too heavy and had too small a surface area to be really affected by the fans flow That was a silly idea! Brad idea was much better Quote Link to comment Share on other sites More sharing options...
R2Dan[TK] Posted April 21, 2011 Report Share Posted April 21, 2011 you need a stronger fan! More power! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.