ocmano

43, too young. Rest in Piece. Buckets off. Sent from my SM-G986U1 using Tapatalk

POST 66 2019 Woodland Park Zoo Lights Seattle, WA Garrison Titan Fire Team Orca 1. 2019 Buddy Walk for Downs Syndrome Seattle, WA Garrison Titan Fire Team Orca 2. 2020 Everett Silvertips Star Wars Night Everett, WA Garrison Titan Fire Team Orca 3. 2021 Washington Summer Con Puyallup, WA Garrison Titan Fire Team Orca 4. 2021 Washington State Summer Con Again Puyallup WA Garrison Titan Fire Team Orca 5.

Been a couple years, but Trooped with my TK recently. Charged up the iCOMM system and a inital test seemed fine. But after about 5 minutes, with it on voice activate, the iCOMM red light comes on and the speakers just start clicking repeatedly. I think it might be the iCOMM tl-2450 3.6v battery dying. Looks pretty easy to replace. Am I on the right track? Sent from my SM-G986U1 using Tapatalk

E11 should it be gloss, semi gloss or flat black? Sent from my SM-G955U1 using Tapatalk

Got the Field Marshal kit and looking to start painting before the BlastFX electronics show up. However, have zero experience painting Aluminum so is there a recommended primer and paint I should use? Will be painting parts before assembly, so don't want something that'll be too thick and create issues. Thanks!

Great job! Took your time and got it right. [emoji106] Sent from my SM-G955U1 using Tapatalk

Sharp Brian! Good luck! Sent from my SM-G955U1 using Tapatalk

Congrats on EIB. Great job! Sent from my SM-G955U1 using Tapatalk

Nice work dude! Sent from my SM-G955U1 using Tapatalk

Man, don't know how I missed your thread. Congrats on doing a AM build! Nice to have another AM kit in Garrison Titan.

It come with any assembly instructions? Was thinking about getting one of these kits and try and put in BlastFX electronics. Not sure I'm ready for another project yet. Sent from my SM-G955U1 using Tapatalk

Solid work Sir! Great to see another AM build. Sent from my SM-G955U1 using Tapatalk

I got a Quest Designs E11 off of Etsy, it's very good. Highly recommend them. It's about a 3 month turn around with them though. Sent from my SM-G955U1 using Tapatalk

Updated photo of the mic tips pointing down now. Still pending redo on the side straps, but since thats a lot of chemicals, going to wait till summer when I can do it with lots of ventaliation. Sent from my SM-G955U1 using Tapatalk

Also Titan Garrison here, Welcome aboard trooper! [emoji106] Sent from my SM-G955U1 using Tapatalk

Got straps doubled over now and drying. Marked the locations for new side strap holes based on the measurements. Looks like all three need to shift up. Going to test some abs paste that I'd use to fill the holes on a coverstrip first before I start the side strap move. Want to be able to fill the old holes and make it blended before cutting new ones. Sent from my SM-G955U1 using Tapatalk

Alright got the mic tips adjusted. Put a little triangle of padding behind the top of the back and it points slightly down instead of up now. Going to double over the shoulder elastic next, it pulls out with only one layer. Sent from my SM-G955U1 using Tapatalk

Alright, for the rivets, just need to move the top two right? Bottom one looks like it's correct. Sent from my SM-G955U1 using Tapatalk

Roger that. Here's the forearms from the wrist end with a couple angles. Guess your looking for return edges?

As requested here's some side shots with no Belt. Left Right Flexible Hand guards on the other set of Gloves (Have 2)

It does. The AM kit kidney and Ab lines up, so no kidney notches. Sent from my SM-G955U1 using Tapatalk

Mandatory Information Armor = Armor Master 2.0 Helmet= Armor Master 4.5 Blaster= Quest Design EIB Thread: Optional Height = 6'1" Weight = 235 lb Boots = Imperial Boots Canvas belt = TrooperBay Hand Plates = AM 2.0 Hard Electronics= Ukswraths hovi mic and fans Neck Seal = Darman Holster = Darman Adjustments from EIB Feedback: Helmet frown, painted the edge after the uncut tooth. Got wire and created new brackets for the chest piece edge that are 1/2 inch longer so the chest sits lower. Added outer edge elastic straps to hold the butt plate flush with the lower back. Tapered the forearms around the wrist by 2cm. Any more and I'd have a hard time getting my hands through. Trimmed the front thigh cover strip to be 20mm instead of 30mm. Used the 2nd belt cover, trimmed the corners less than the first and added the raised rivet covers vs the sunk covers on the old one. AB button plates, square the edges and touch up the button paint. Adjust left forearm to bicep strap a cm or two longer to line up better with right. Armor Photos Full Body Front Full Body Back Full Right Full Left Right Side Detail Left SIde Detail Armor Details Gloves Shoulder Bridge Front Shoulder Bridge Back Thigh Pack Attachment Sniper Knee Attachment Drop Box Back Crotch/Butt Detail Helmet Detail Photos Front Side Back Hovi tip detail Lens color (Backlit if necessary) S-Trim Accessory Photos Ammo belt Neckseal Blaster left side Blaster right side D-Ring Thermal detonator back Action Shot Optional Interior Strapping Abdomen Detail

Putting a list here to track changes made that were for Centurion. 1. Helmet frown, painted the edge after the uncut tooth. 2. Got wire and created new brackets for the chest piece edge that are 1/2 inch longer so the chest sits lower. 3. Added outer edge elastic staps to hold the butt plate flush with the lower back. 4. Tapered the forearms around the wrist by 2cm. Any more and I'd have a hard time getting my hands through. 5. Trimmed the front thigh coverstrip to be 20mm instead of 30mm. 6. Used the 2nd belt cover, trimmed the edges less than the first and added the raised rivet covers. Vs the sunk covers on the old one. Still to do: 1. AB button plates, square the edges and touchup the button paint. 2. Adjust left forearm to bicep strap a cm or two longer to line up better with right.

Thanks! Should be able to take care of the easy stuff, like extending the frown paint, or adding butt elastic straps, quickly. Some of the others that take glue and trimming might be a while. Lost my workspace for now, but hope I get room to finish it up again. Wife isn't wild about me taking over the kitchen and livingroom. [emoji6] Thanks! Sent from my SM-G955U1 using Tapatalk

Alright new front sides and back. Fixed: Shin back cover strips and opening to the inside instead of outside (Note: I had Achilles tendon surgery on my left side so that calf is in fact smaller than my right by a little) New Loop in Chest ABS connection that's larger and adjusted the pull strap so there's no gap. Adjusted forearm to bicep straps to have less wrist showing. Belt straight Thanks! Let me know. Hopefully nothing major left.