Jump to content

repentance3232

Member
  • Content Count

    56
  • Joined

  • Last visited

About repentance3232

  • Rank
    Sergeant

Standard Info

  • Name
    John

Recent Profile Visitors

116 profile views
  1. repentance3232

    SNAP Setting 101

    Ok. I hope you actually got a little chuckle out of this, I sure was laughing at myself. I see now what I need to do with moving forward in web strapping Sent from my SM-G965U using Tapatalk
  2. repentance3232

    repentance3232 WTF ANH HERO BUILD

    Hey Paul I looked to see where my E6000 was manufactured and it is in USA, not China Sent from my SM-G965U using Tapatalk
  3. repentance3232

    repentance3232 WTF ANH HERO BUILD

    I didn't bend it. I actually sliced through it with a butter knife Sent from my SM-G965U using Tapatalk
  4. repentance3232

    repentance3232 WTF ANH HERO BUILD

    Believe me, I was quite surprised to see deformation after the removal of shoulder covers. It makes sense that what could have caused it was possibly both excessive glue and force from clamps Sent from my SM-G965U using Tapatalk
  5. repentance3232

    repentance3232 WTF ANH HERO BUILD

    lucnak, really I am only worried about chest deformities from E-6000 for my submissions for L1, L2, and L3. My shoulder elastic stays on shoulder covers but slips off of back plate and rest on shoulder elastic straps that connect chest to back plates Sent from my SM-G965U using Tapatalk
  6. repentance3232

    SNAP Setting 101

    Help me, you are my only hope Sent from my SM-G965U using Tapatalk
  7. repentance3232

    SNAP Setting 101

    Cut the 2 inch strapping to about 4 inches long or thereabouts. Cut the 1 inch nylon into 2 inch lengths as seen below. Ok, someone needs a good laugh!!! I cut 2" nylon in the length of 4" and followed the instructions and this is what I ended up with. I think I did something wrong because my gap is very visible Sent from my SM-G965U using Tapatalk
  8. repentance3232

    repentance3232 WTF ANH HERO BUILD

    I have a concern. I E-6000 shoulder covers for 24hrs and realize 5 bumps in the front was to much. That caused no bumps on back plate. I removed shoulder covers and reglued. The chemical in E-6000 caused the chest plate to rise in a slight deformation. How do I get my chest plate @ front shoulder covers to look right again??? Next picture of shoulder cover rear elastic. Is it supposed to be tied around back plate??? It wont stay in position and slips of back plate easily Sent from my SM-G965U using Tapatalk
  9. repentance3232

    repentance3232 WTF ANH HERO BUILD

    Hey justjoseph63, just giving you an update on cod strip. I replaced strip and doubled and stitched both ends Sent from my SM-G965U using Tapatalk
  10. repentance3232

    repentance3232 WTF ANH HERO BUILD

    Question on my right side calves. Is that to much of a step difference??? Should I trim it??? I would like to have a little step difference. It 5MM off center. Sent from my SM-G965U using Tapatalk
  11. repentance3232

    SNAP Setting 101

    Hey Commander, just curious if you had to make any adjustments after your evaluation with your elastic??? Sent from my SM-G965U using Tapatalk
  12. repentance3232

    repentance3232 WTF ANH HERO BUILD

    Thank you Ukswrath, I have started the rework on front shins Sent from my SM-G965U using Tapatalk
  13. repentance3232

    repentance3232 WTF ANH HERO BUILD

    I also need to mention, I peeled back cover strip about 4inches for room to trim. Can I pull old E-6000 off and reglue or pull the whole cover strips off and reglue??? Sent from my SM-G965U using Tapatalk
  14. repentance3232

    repentance3232 WTF ANH HERO BUILD

    Better pic of cover strip Sent from my SM-G965U using Tapatalk
  15. repentance3232

    repentance3232 WTF ANH HERO BUILD

    Will this work??? Sent from my SM-G965U using Tapatalk
×