HSM76

Welcome Brother, great work! Gesendet von meinem ONEPLUS A6013 mit Tapatalk

I have an RS kit, but I think the ears are in any case tricky little things. Take your time and remove just a little bit at a time. You can always remove a bit more l, but adding material is a real pain. Gesendet von meinem ONEPLUS A6013 mit Tapatalk

Looking good! Gesendet von meinem ONEPLUS A6013 mit Tapatalk

Wow.... Haven't seen that. But I think pouring water over it was the problem. I put the whole shin in the, in my case boiling water for about 20 seconds. While it was in the water it was taped with painters tape. After that I took it out and twisted it gently against the current direction. While cooling it down with lukewarm water in the shower. Gesendet von meinem ONEPLUS A6013 mit Tapatalk

The easiest way for me was a hot water bath, the hardest part there was to get a pot that was big enough. Gesendet von meinem ONEPLUS A6013 mit Tapatalk

Wow, lucky you! Great number and welcome to the ranks! Gesendet von meinem ONEPLUS A6013 mit Tapatalk

Very cool, welcome to the legion.

Sven Müller 24576 Centurion A4 Shasha Thanks in advance. http://www.whitearmor.net/eib/certificates/24576-centurion.png

Sven Müller 24576 EIB A4 Tony Thanks in advance! http://www.whitearmor.net/eib/certificates/24576-eib.png

Thanks very much, you all! I am so happy!

Hi Andrew, sure you may:

Looks a bit more interesting than the real thing :-) Gesendet von meinem ONEPLUS A6013 mit Tapatalk

Great to hear that, congratulations! Gesendet von meinem ONEPLUS A6013 mit Tapatalk

TRamp also does full comission installs in an SDS E11. But that comes in at about 500£ plus shipping.

Between chest an arms can only be the under suit itself, the neck seal bib itself is not that wide. Hmmmm... Have to look into this. For the back, it will help, there you are right.

Thanks. No the neck seal is over the undersuit.

Yep, saw that to late, while uploading the photos, must have happened, while walking down the stairs :-(

Name: Sven Müller Forum name: HSM76 Legion ID: 24576  Armor maker: RS Prop Masters Helmet maker: RS Prop Prop MastersArmour Maker: RS Prop Masters Helmet Maker RS Prop Masters Blaster: Real Sterling, real Scope, real Hengstler, PlayfullWolfCub cylinders. Height: 185cm (roughly 6‘1“) Weight: 75kg (165 pound) Boots: imperial Boots Belt: RS Prop Masters Electronics: Ukswraths Hearing aid, Troopacoola Fan system. Neck seal: Burbench Designs Holster: Imperial Supply Depot Build thread: EIB request: Front: Back: Left: Right: Left detail, split rivets, kidney notch: Right detail, Han snap, kidney notch: Butt / Kidney seperate, internal strapping: Hand plate latex: Shoulder bridge front: Shoulder bridge back: Thigh pack attachment, single cap rivet: Sniper plate: Drop box back: Cod / butt attachment, 2 snaps, brass split rivet Wrist left: Wrist right: Helmet front: Helmet back: Helmet left: Helmet right: Helmet Hovi Mix detail: Helmet lens colour: Helmet S-trim: Blaster right: Blaster left: Blaster O-Ring: Neck seal: Thermal detonator: Holster attachment: As stated in my EIB threat, I will see what I can do with the return edges of the Helmet eyes and if it is possible to reset the ear. But that will be something for spring or early summer :-)

Maybe someone with more experience with AP can chime in.

I am not sure how the AP looks underneath, I have an RS Suit, but it should be straight, this is how my left knee cover strip looks:

Should be no problem if you are careful. Here how it should be (minus the rivets):

I just looked through your thread and noticed that the thigh cover strip is to long, they should end before the ridge at the knee.

Thanks for the congratulations. I think I found out, why the sides were set of. It was the fault of the back plate, the shoulder strips are uneven on the RS kit (okay, the question now is, what is even on this kit, or the screen used armour :-) ) I hear bent this part bit around , I think now it will be okay. Unfortunately I did not get to making new pictures last weekend, I hope next one I can do it and submit for centurion.

No, this is no problem for centurion, the internal strapping is up to you. There are a lot of centurions with a snap system for internal strapping. All that is needed is the outer appearance. If you have the movie accurate strapping, this is the countersunk screws, that have heads that are painted white.

I would take of everything that looks like it is flashing from the vacuforming, like this: It's a bit crummy, but the best I could do on my mobile. I hope it gives an idea, what I mean.