Leaderboard

Now that it is pieced together do you think the center grey area (or central panel) may be a touch too wide? Grey area appears narrower and higher on the pauldron. May be too much of a gap between the red panels. Tried to get these images roughly the same size, reference is slightly on an angle though. It's pretty darn close and if you are happy with it leave it as is

Hello! Just wanted to share my progress on my Enoch build. This build has been completely homegrown except for the boots. From all of the printing, to all of the sewing of undersuit and leather pieces, to the fabrication of the blaster. I am nearly done. All of the armor were files from Galactic Armory. I decided to give resin printing a shot on all of my armor. I have made several kits using FDM but just loved the detail of resin. So decided to give it a shot and I am very happy with it. https://imgur.com/a/iKabdej

Name : Francois Pelletier TK20236 Forum name: Sithtrooper02 Garrison : Forteresse Imperiale Garison Social Media consent (photos) : YES ***This is the costume that was used to create the Imperial Armored Commando CRL Armor : 3D printed/finished by me - see the build thread in the Imperial Armored Commando Helmet : 3D printed/finished by me Blaster : Designed and 3D printed/finished by me Height : 5’7’’ Weight : 165lbs Boots : Crowprops Imperial Commando boots Canvas Belt : designed and Fabricated by Veronique Jomphe Gloves : Crowprops Imperial commando leather gloves Suit : Keeptrooping suit modified to comply with CRL and added attachment points for the armor Link to approved armor : https://www.501st.com/members/displaymember.php?userID=39822&costumeID=664 The pictures (most of them are already on the CRL reference images): Action pose Helmet OPTIONAL Level two certification (if applicable): Protruding ear section is visibly a separate piece. Clip greeblies and strap are visibly separate pieces. Aerators and diamond greeblie are visibly separate pieces. The collar has vent with oblong holes on the rear section. Flight Suit OPTIONAL Level two certification (if applicable): Flight Suit is one piece construction. Long sleeves do not have horizontal quilted ribs on the inside of the arm between the short sleeves and the gauntlets. Chest armor OPTIONAL Level two certification (if applicable): The 4 sections and shoulder box are visibly separate parts. The ranking box components have thickness and are visibly separate parts. The raised box over the right shoulder is visibly a separate part and has two semi-circular recessed lines on the outer side and a recess on the inner side. The raised box grid has exactly 5 vertical rectangular grey shapes and is visibly a separate part. Back OPTIONAL Level two certification (if applicable): The jet pack has 3 attachment points that are visibly separate parts and have a metallic finish. The two upper attachment points are circular T-shaped and anchored to the back plate with a circular plate. The lower attachment point to the jet pack is cylindrical with a taper at the tip and is anchored to the back plate with a rectangular plate. Jetpack : OPTIONAL Level two certification (if applicable): All grey and black components are visibly separate parts. The bottom grill is visibly a separate part. There are 5 small black vertical cylinders attached atop of the large grey box. The vertical cylinders ends have a 90° bend inward at the bottom and the top. They are not all equal in length at the top, as the middle cylinders are longer than the outer cylinders. Abdomen section OPTIONAL Level two certification (if applicable): Only one seam is present on the right side of the wearer’s side. The 4 straps are all identical in width and geometry There is the appearance of a clip on the straps approximately at the middle of the abdomen armor. Belt OPTIONAL Level two certification (if applicable): The push release button of the female buckle is visibly a separate component. There is a rectangular recessed line on the metal portion of the male buckle. The metal portion of the male buckle is followed by a black section entering the female buckle. Shins OPTIONAL Level two certification (if applicable): The shin is a single piece construction with a seam only present at the rear which overlaps to the outside. The rear spat box has a recessed edge on the outside creating a smaller shape. The spat overlaps the boot with minimal gap. See main pictures for overlaps Boots OPTIONAL Level two certification (if applicable): There are 3 stitched lines that run across the instep. The instep is made of thick material with the 3 stitched lines creating raised sections. Standard FOTK boots are not acceptable.

Done, thanks!

Hi Trooper, we're almost ready sir. just we'll need you to add the Blaster and pistol photos to your application. Thank you.

Progress! Red and grey panels have been glued down, but... I'm not sure I'm happy with the connecting panel. Might redo it but overall it's looking good. Next is to ensure the fit is right and then add the magnets that hold it on.

I cut that entire front section out and just filled it with JB Weld Plastic epoxy, needs a little more smoothing but whatever was eating the paint is now gone.

Good times had with the crew at South Carolina Comicon!!!!