Jump to content

TK 10963 Requesting ANH Stunt Centurion status (AM2.0/ATA)[167]


Recommended Posts

Name:  Joseph Pedigo

Forum name:  justjoseph63

Garrison:  Florida (Makaze squad)

ID:  TK 10963

Armor:  AM 2.0 / ATA *

Helmet: AM 2.0

Blaster:  Doopydoos full resin mod

 

Ht:  5' 10

Wt:  155

Boots:  Imperial boots

Canvas belt:  Imperial issue

Hand plates:  Home-made latex

Neck seal:  Darman

Holster:  Gazmosis

 

*  AM 2.0 chest plate, back plate, ab, and kidney were replaced with ATA.  Kidney and ab were replaced due to rivets being in the wrong position, and back was replaced as it would not fit with new ATA kidney. TD plate (too narrow) was replaced with wider TM plate.  Also, my apologies for the lame "action shot".   Thank you for your consideration.

Side note:  I noticed my bicep elastic is too high, and keeps slipping upward.  I will remedy that today  Update: DONE, (pic added in last post).  TD screws updated to flat head (see photo in 2nd post).

 

20150620_194829_resized_2_zps0utya0uk.jp20150620_194940_resized_2_zpsnihglcxw.jp20150620_194957_resized_2_zps7zr0e8hw.jp20150620_195036_resized_zpsivaie7k2.jpg20150620_195103_resized_zpsjj66fqni.jpg20150620_174251_resized_zpsl7af6xmh.jpg20150620_174310_resized_zps73dgrtd5.jpg20150620_174445_resized_zpsu4l79nan.jpg20150620_153201_resized_zpsav4wixyh.jpg20150620_153121_resized_zpshnzyjimq.jpg20150620_152214_resized_zpsbk7owdba.jpg20150620_152338_resized_zpsna63vxqb.jpg20150620_100951_resized_zpsljlzcqhb.jpg20150620_104654_resized_zps1wmd4ldx.jpg20150620_101053_resized_zpst3lc2kax.jpgIMGP0363_zpsxf7zrjrt.jpg20150620_101229_resized_zpsmugm2vhy.jpg20150620_101258_resized201_zpsaaa7ko8z.jIMGP0333_zpsjvvrpkrm.jpgIMGP0336_zps7zk2emmn.jpgIMGP0337_zpsso7qufzm.jpgIMGP0339_zpsz8jvpxfk.jpgIMGP0338_zpsre5temju.jpgIMGP0360_zpsmhms67ph.jpg9cacb4cb-4396-4638-a355-9181b280abd3_zpsIMGP0362_zpsarigstok.jpg20150601_150755_resized_zpsm2vblyjq.jpg20150601_150417_resized_zpsg0pm783l.jpgIMGP0349_zpsi3ozaxo8.jpgIMGP0342_zpsrzgpv86h.jpgIMGP0341_zpsg4q4fkik.jpgIMGP0344_zpsxpbbgc75.jpgIMGP0343_zpshlfe5hzp.jpg

IMGP0346_zpsxkdjy1ya.jpg

Edited by justjoseph63
Link to comment
Share on other sites

Only thing I see that really stands out is you spelled 'left' wrong.   :laugh1:

 

Awesome job!  Folks might recommend swapping your screws out on the TD to slotted, but not required.  Good luck!  

  • Like 1
Link to comment
Share on other sites

Good eye, and thanks, Scott!  Screws have been replaced and painted.  Unfortunately, Photobucket will not let me change the spelling now that it's done, so there is nothing lest to do but leave it as it is. :P

20150621_190703_resized_1_zps6j8vjku8.jp

Link to comment
Share on other sites

Alright Joseph! Your jorney has finally arrived! Thank you for your Centurion application and let's get to it!!!

CRL and Centurion Application Requirements:

All the required submission photos have been posted. Your armor now contains all necessary details to obtain Centurion. Congratulations and welcome!!!

 

Other-Armor Fit/Assembly:

With your arrival at Centurion, there isn't much to add in this section. I would like to add for those following along that the original shot near the top of the wrist openings of Joseph's forearms showed remaining return edge within the opening at the square intent ridge. ALL return edge within the opening is required to be removed which Joe has done.

It is also important to note that Joe's original costume was the AM chest which has been replaced with a more accurate version and it was WELL worth it!!

I like the improvements done to your Thermal Detonator as well in the overall length and the new screw hardware. 

If there was one other thing I would look into, it would be the correct screw hardware for the front of your scope. "X" head screws were never seen here as in this scope exampleScopebuild6_zpsffqzdmfa.jpg

Well done and congrats overall!!!

  • Like 1
Link to comment
Share on other sites

Thank you SO much, Steve!  You have gone above and beyond the call of duty on this one with all the help and answers to all my odd questions.  I will get those scope screws taken care of this afternoon... Next up, HWT Centurion

Edited by justjoseph63
Link to comment
Share on other sites

Thanks, Tony, and I appreciate your help in getting here!  (Nice pics, eh)?  :D   Installing your hovi-tip mic system tomorrow... can't wait!

Link to comment
Share on other sites

Thanks, Steven!  Anything I can do to help you out, just let me know!  What armor did you go with?

Congrats!!

 

I'm ordering the AM 2.0 next month. Still kicking around the idea of a different helmet, though. I figure I'll do the AM chest and back at first for basic approval, and I'll get a more accurate replacement down the road.

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

No, but it certainly does look like it!  What that is, Sean, is a small indentation that AM builds into the ear guard to assist you in the correct screw placement.  Mine happened to be off by about 1/32 of an inch, and is casting a small shadow. 

Link to comment
Share on other sites

 

 

 

 

ç§ã¯ã‚ãªãŸãŒãれを好ã幸ã›ã§ã™ã€éžå¸¸ã«ã€ã‚ã‚ŠãŒã¨ã†ã”ã–ã„ã¾ã™ï¼
Link to comment
Share on other sites

Ah cool. My two AM 2.0 kits were off as well and I just finished wrestling with them. I just drilled new holes in the helmet halves rather than the ear. Thanks for showing us what a right AM kit looks like.

  • Like 1
Link to comment
Share on other sites

  • 3 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...