TK5492[TK] Posted April 16, 2012 Report Share Posted April 16, 2012 Respectfully requesting being granted EIB status. Thank you for your consideration. Tyler Fox/TK 5492 Forum name: TK5492 Japanese Garrison Armor= FX/ATA hybrid (Chest piece, back, shoulder bells, and shoulder straps are ATA) Helmet= eFX Modded. ( Ear screws added, old lenses removed and green welder’s lenses added, teeth dremelled wider and repainted, mesh added, seam filled, ears repainted, old too dark tube stripes removed and new Trooperbay correct style stripes added. ) Blaster= Doopy Doo’s full resin kit Height = 5’ 6†Weight = 150 Boots = TK boots Canvas belt = custom made Hand Plates = Trooperbay Gloves=Trooperbay rubber chemical Neck Seal = Unknown - From an old kit Holster = Unknown- ditto Drop boxes= Enclosed with scrap ABS Thermal Det clips= custom I bought this armor before I got into FISD and knew the information I do now. I have tried to take what I have learned and make it the best I could with my budget and living abroad. Please let me know if you have any questions. Thank you. I think that covers everything. Thanks! Quote Link to comment Share on other sites More sharing options...
Faie[TK] Posted April 16, 2012 Report Share Posted April 16, 2012 Good job trooper! Quote Link to comment Share on other sites More sharing options...
TK bondservnt[501st] Posted April 16, 2012 Report Share Posted April 16, 2012 (edited) the only thing I see is the thickness of the ears. other than that and the 4th tooth detail needs some more photo evidence I have the mrce efx lid I moded for hero. and it requires the thinning of the ears. Edited April 16, 2012 by TK Bondservnt 2392 Quote Link to comment Share on other sites More sharing options...
Dr.Senf Posted April 16, 2012 Report Share Posted April 16, 2012 both seams on the lid are pretty visible and the forearms should be fully closed. you used velcro there if i see it correctly. in my opinion you should remove the returnedge on the shoulderbells. just my 2ct Quote Link to comment Share on other sites More sharing options...
TK5492[TK] Posted April 16, 2012 Author Report Share Posted April 16, 2012 (edited) Thank you for your observations Sven. The seam is not ususally visible. It may be the lighting in this picture. I could try to re-fill it. As to the forearms- I do not recall seeing in the CRL that the forearms MUST be glued shut. If so, I would never get my hand through with my gloves on. And lastly, Isn't the return edge on the shoulder bells desireable and correct? I started a thread awhile back about replacing my chest and back and I was told to replace the shoulder bells as well for this very reason. Also, in every other ANH EI application I looked at, everyone had a return edge. Edited April 16, 2012 by TK5492 Quote Link to comment Share on other sites More sharing options...
Dr.Senf Posted April 16, 2012 Report Share Posted April 16, 2012 like i said in my opinion there should be no return edge. its a snug fit then. i have a mrc for display aswell and it was pain to close those seams but you can make them disappear completely and it looks much better trust me. http://www.501st.de/board/index.php?topic=270.555 check it out. but painting is required. no must to glue the forearms but theres always a gap now since velcro is thick. most tks have them glued shut. Quote Link to comment Share on other sites More sharing options...
TK5492[TK] Posted April 16, 2012 Author Report Share Posted April 16, 2012 I see now what you are saying. There is a gap because of the velcro but the only time it is visible is when it is close like that. I believe sometimes small things must be done to maintain practicality as well as accuracy. You're MRCE is very nice. I can attempt to try to make the seam better. Quote Link to comment Share on other sites More sharing options...
Dr.Senf Posted April 16, 2012 Report Share Posted April 16, 2012 its the extra mile to make it even better with little efford. your choice and descision when you re satisfied Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted April 17, 2012 Report Share Posted April 17, 2012 While there may still be room for improvement, I'd say this is one of the better mrce/fx-combos I've seen in a long time. Good job! Approved! Quote Link to comment Share on other sites More sharing options...
Thalizar[TK] Posted April 17, 2012 Report Share Posted April 17, 2012 Way to go Tyler! Quote Link to comment Share on other sites More sharing options...
TK5492[TK] Posted April 17, 2012 Author Report Share Posted April 17, 2012 Wow, Thank you so much! It's an honor. I couldn't have done it without everyone on these boards. Thank you. Quote Link to comment Share on other sites More sharing options...
Dazauto[TK] Posted April 17, 2012 Report Share Posted April 17, 2012 Well done and congrats Tyler, great work trooper Quote Link to comment Share on other sites More sharing options...
senna1rossi[TK] Posted April 18, 2012 Report Share Posted April 18, 2012 proof that you could retrofit an FX for EIB approval! great job! CONGRATS on your EIB! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.