Gwithian

Humm..... will have to get some of them.... must admit your boots look much better than mine [emoji3] Sent from my iPhone using Tapatalk

Yes mine are painted.... I didn’t realise RS did white leather ones .... I think I will have to get in touch with them. Were they a special order? Sent from my iPhone using Tapatalk

Looking good Stefan [emoji3]... I have the RS boots, they scratch quite easily when the greaves are fitted, so be careful.... see mine... doh Sent from my iPhone using Tapatalk

A bit more progress today..... I was prompted by Christine aka cricket on FISD to make some stirrups for the greaves..... I’ve followed the instructions she gave me and hopefully they will keep them in place And In the boot The Velcro will be attached to the soft part inside the greave.... it needs sewing onto the elastic before I use them The soft bit inside the greave I’ve also cut out the rivet covers fir the belt, 1” square They just need gluing on the belt now Also I’ve painted the buttons for the ab,... I did a dry run on some scrap abs before I started hopefully they are ok... are they big enough? Sent from my iPhone using Tapatalk

Lid and boots looking good mate [emoji3] Sent from my iPhone using Tapatalk

I’m so so sorry to hear of your sad news Stef, may your mother rest in peace and live on in your heart . You are in our thoughts and prayers Sent from my iPhone using Tapatalk

Well I’ve finally bit the bullet and cut the cod.... measured 1inch in (bottom line) then half an inch in (top line) And decided to go fir three quarters of an inch (middle line) Started to cut... no going back now.... oops I’ve been well and truly snipped now And taped in place.... Had a quick try and it seems ok.... will do another fitting in the next few days .... This is something that I was hoping I didn’t need to do but sadly it’s been necessary..... Next job may well be to trim the butt.... does the butt need a return edge in the side / bottom edge? Sent from my iPhone using Tapatalk

Thanks Frank, I appreciate your help Sent from my iPhone using Tapatalk

Ok today I’ve been trimming the shoulder bridges, the abs button plate(the small one) and the thigh ammo belt First the shoulder bridges I believe the shoulder bridge widest bump goes to the front and five bumps (or us it ridges) goes on the chest piece like this Then onto the ammo thigh Trimmed Does this radius look ok But what is the length from the last ammo block to the end? Ab buttons trimmed And taped on the ab.... is this looking ok? Following on from yesterday ..... I think I need to cut the cod..... to help to give a gap between the cod and thighs.... I guess I will have to bite the bullet tomorrow ..... Another step forward Sent from my iPhone using Tapatalk

Hi Christine, I will do as you suggested.... your post was very delicately put.... do you work in the diplomatic service Sent from my iPhone using Tapatalk

Hi Christine, thanks for the feedback . I remember the Halloween pictures you posted last year.... they were amazing . Yep thigh ammo belt working on today, don’t k is why the right thigh is playing up? Need to take another look at it.... hope I haven’t cut it wrong The belt fell off the snaps so I’m going to fit some industrial Velcro like you advised frank Now a very important question.... do I need to cut the cod? I’m thinking it may just give me a bit of room around the thighs? What do you think? Stirrups... I haven’t done them yet... tried snaps and couldn’t snap them.... also thought if magnets? May have to go down stirrup route I’m getting there slowly but surely I appreciate all your help Sent from my iPhone using Tapatalk

I’ve tweaked the butt, the arm strapping and the ab / chest strapping .... then I tried it on again Now apologies... the excess belt is showing over my thigh .... I will cut that off.... also the left shoulder Bell snap came undone... doh.... Anyway you will get the idea of how it’s coming together Actually it’s a lot easier to walk in than I thought.... indeed I dropped the remote camera button on the floor and managed to bend down to pick it up .... didn’t think I would be able to do that.... well chuffed So pics I think it’s coming together well. How is the chest /ab looking re where the buttons will go Thanks for all your help I could not have done this without the UKG or FISD Sent from my iPhone using Tapatalk

Some more progress made over the past couple of days... however I’ve ....well ..... I was trying to heat the butt to try and get it to fit better and this happened Got it a bit too hot and put my thumb in it.... not too sure what to do... leave it as it is ? Or try and heat it out? Thoughts appreciated .... I’ve been working on the thighs, trimmed the excess and then rebuilt the return edge with a heat sealing iron Used some abs paste to Smith things out... just needs sanding now I have reworked the left greave to make it fit better around the boot ... I had to remove the internal magnets I then had to re trim the greave Then glued it all back together They fit a lot better now I know it’s daft but I wore these today whilst I was working on the armour, the right is perfect but the left actually it’s the sniper knee plate digs into my knee... so I think it needs some padding .... they didn’t ride up at all when I was walking around ... oh attached magnets to the boots Then tweaked the shoulder bells and arms.... they fit much better now Then fitted the drop boxes and riveted the amp to the belt The green tape marks where the drop boxes need to align to when the ammo is removed All riveted up And on the ab Some good progress but gutted about the heat damage to the butt.... hay me n heat guns don’t go well together lol Sent from my iPhone using Tapatalk

I have attached the biceps to the bells with snaps , I’ve adjusted them and got things more aligned .... will do another fit next week but the arms are now feeling much better .... thanks Sent from my iPhone using Tapatalk

Thanks for the advice:) I will look at the arms... I don’t think Ibadan the biceps up high enough? So I will check that out first . I will also have a look at the chest I’m getting there bit by bit Sent from my iPhone using Tapatalk

Today I’ve fixed the drop boxes to the belt Not too sure if it goes here Or here I also installed some Velcro.... the soft side to the outside of the TD brackets.... hopefully that should stop the brackets from scratching the kidney armour All done Then I fitted the inner cover strips to the thighs.... after test fitting yesterday , the right thigh was perfect. The left was a bit too wide so I trimmed it about 7mm and then fitted the inner strips One final question.... the back of the thighs do need trimming..... I’m guessing they need to be trimmed as shown by the yellow tape in the pics below Another step forward today Sent from my iPhone using Tapatalk

Well today has been the first proper test fit of my armour ..... boy it was difficult to get on .... much harder than my motorcycle leathers ...... oh and sorry..... I couldn’t put my lid on .... so you will see a rather old and ..... well only a face a mother or wife could love..... you have been warned..... My biking mates make me wear a black visor so they can’t see my mug when we are out riding..... see Anyway... back to the armour... I’m chuffed in part and well not so chuffed in others..... The torso isn’t as bad as I thought and I can’t get the cod any higher without singing an octave higher .... I thought I may need to cut the cod but now I think it’s ok I’m happy with the thighs, they need trimming at the back but the front seems ok? ... the right thigh wasn’t on very square I don’t know why? The right greave fits well but walking around a bit I found that the return edge at the top of the greaves was rubbing against my knee.... perhaps a bit of foam in there will do the trick... The left greave rode up and came over the boot.... it’s too wide at the ankle so I will take it in a bit I’m pleased with the TD and the ammo belt .... one question.... are the drop boxes riveted to the ammo belt or held on loops.... I have found advice which recommends both do I don’t know which is right? As I said it was really difficult to fit the armour..... my shoulder bells are still too big.... I did manage to fit the left bell to the shoulder snap but with the left arm armour on I couldn’t reach the right shoulder snap ... so the bell kept falling down..... how on earth I will manage the shoulder elastic...... well that..... thankfully is a problem fir another day.... Given the difficulties I’ve experienced today it’s no wonder the pesky rebellion has gathered ground..... I mean if we can’t get our kit on.... never mind navigate steps and not mentioning the inaccuracies of our blasters...... it’s no wonder we are struggling to retain law and order in the galaxy ...... You will understand my frustration when you see the pics..... Advice much appreciated..... sorry about the mug shot [emoji20] And the belt...... rivet or loop? Thanks for your advice..... I’m getting there.... rather slowly..... [emoji4] Sent from my iPhone using Tapatalk

Thank you for your kind words, I’m glad you have enjoyed my thread and the odd diversion I’ve been on.... Not this year. But we went here last year... thought you might like From the other side And saw this Just a little diversion..... back to imperial duties now Sent from my iPhone using Tapatalk

Post deleted.... for some reason I managed to double post the previous post.... doh Sent from my iPhone using Tapatalk

Today I’ve been strapping the torso together..... I have hand stitched the elastic.... and used bolts to hold the an and kidney together..... the idea is that I can dismantle the torso if I need to trim it down.... which I think I will .... well I’m not known for being tall lol Anyway hopefully first fitting tomorrow and we will take it from there Position of the rivets Various pics of my rather unusual strapping Actually the butt and kidney go well together Pity the same can’t be said fir the back piece All strapped together As I said... this is all temporary ... so I can easily dismantle it if need be .... the bolts will be replaced with the split rivets once everything is sorted.... I do think I’m going to have to reduce the torso...... didn’t realise I’m not as tall as I thought/ think .... doh Sent from my iPhone using Tapatalk

Thank you Sir Sent from my iPhone using Tapatalk

No I didn’t find the answer to that but I’m I had come to the same tonight process as you Sent from my iPhone using Tapatalk

I think that’s a great idea and I’m sure your son will enjoy trooping with his stormtrooper dad [emoji3] Sent from my iPhone using Tapatalk

I keep referring back to your build thread and Christine’s...... I would have been lost without them [emoji3] Sent from my iPhone using Tapatalk

Sorry it’s the biceps and forearms I’ve been working on today.... don’t know why I forgot .... doh Sent from my iPhone using Tapatalk