Rat

So I think I officially have a left leg that is 99% complete. Just need to add the suspension strap for the belt and glue down my shin elastic for the bra clips. I did clean up the glue after I took these. Sent from my VK815 using Tapatalk

Got it and thanks. Sent from my VK815 using Tapatalk

Yeah I've been finding that much of it has been just trimming to the initial anovos line and been good for me minus the forearms. So with the back how far back is a reasonable amount? How much tapped should be there? Yeah the frown needs a bit of tlc the more I look at it. Sent from my VK815 using Tapatalk

So I thought I would take a crack at repainting the frown and how do you get this stuff off? Tried 70% alcohol and mineral spirits and not even a dent, but I'm guessing it's very clean. Sent from my VK815 using Tapatalk

So is that too much gap? I think it slipped a bit while gluing. Sent from my VK815 using Tapatalk

Thanks and so I did. Sent from my VK815 using Tapatalk

So more dry fitting and taped the shoulder and chest. I'm not sure why the chest feels like it rides so high and will definitely need to trim some of the neck on the right side and absolutely need to trim the left shoulder tab. Seriously digs. Also not sure how to close up the ab-kidney gap. I tried it with the belt on, but it didn't seem to help and I had it so the velcro was barely connected. Sent from my VK815 using Tapatalk

This is how it looks when used. This is a Hasbro voice changer so the colors are and you can see the difference. It will also be very glossy. Sent from my VK815 using Tapatalk

Those pieces are at the largest 1/4". Let it set over night and stir it to mix as well as checking the consistency. Sent from my VK815 using Tapatalk

Yup already strapped and bracketed. Sent from my VK815 using Tapatalk

Basically paste is small bits of scraps and some acetone. I just used a classic jar filled about 1/3 and a full bottle of acetone/nail polish remover. You just want to make sure that the and is cut into small pieces. Sent from my VK815 using Tapatalk

Right between 5'9" and 5'10" and around 175 pounds so I'm fairly close to screen accurate. Sent from my VK815 using Tapatalk

Yeah I'm a little more comfort with it in this position, but it had a bite to it. Sent from my VK815 using Tapatalk

So a quick update on my progress. I'm using the supplied strapping, but modifying it by adding snaps and using E-6000. Started getting my sew in snaps on and getting my shoulder elastic put on, but I'm not sure if I need to trim anymore any suggestions or advice is very welcome. I'm pretty sure I need to reshape the back plate shoulder strap and it seems my neck is really high and a bit narrow. Sent from my VK815 using Tapatalk

Looks good from what I can see. Though they both seem very cylindrical without much taper to them. Sent from my VK815 using Tapatalk

I believe this is what I'll need to do with my thighs. Very uncooperative. Sent from my VK815 using Tapatalk

Just downloaded and printed and had the same issue with the main body/housing parts and barrel template. The rest were fine though. Sent from my VK815 using Tapatalk

Lowes, home depot or online. Sent from my VK815 using Tapatalk

Thanks, I knew they were shallow but couldn't think of any place I've seen it stated. Sent from my VK815 using Tapatalk

Thanks Tim. I was just getting to my drill holes for my bra straps, but don't recall seeing a measurement for them. Are they just evenly spread down the calves and is there a specific measurement from the edge? Sent from my VK815 using Tapatalk

So after two coats on the top, three on the bottom and setting over night I gave it a quick once over sanding with some 60 grit, then 100, 220, 600 and a well used piece of 600 I think it may be ready for a polish. Sent from my VK815 using Tapatalk

Thanks all and yeah small thin coats I think helped. Sent from my VK815 using Tapatalk

Second coat I think perhaps one more for the bottom and it be good. So how long should I let it set before sanding? Sent from my VK815 using Tapatalk

Forgot the pics. Sent from my VK815 using Tapatalk

So first layer of paste is on. I think I may need a couple of more before I'm sure its good and well sealed and covered. What is a good grit sandpaper for the sanding? I have some either 400 or 600 wet/dry that's probably working more like a 1000 or more. Sent from my VK815 using Tapatalk