All Activity
- Yesterday
-
Looks like you had a lot of fun!
-
Troop #54 Erskine motorbike meet Supporting Erskine Veterans Charity. Is it a bird or is it a plane? No, just a bungee jumper.
-
5/25 - Star Wars Night at Tampa Bay Rays Sent from my iPhone using Tapatalk
-
5/4 - Tampa Theater Return of the Jedi Sent from my iPhone using Tapatalk
-
5/4 - Johns Hopkins All Children’s Hospital Sent from my iPhone using Tapatalk
-
Just one thing for higher levels: OPTIONAL Level three certification (if applicable): The plastic shoulder straps need to be held down in the back via a white elastic band to the white fabric that connects/bridges the chest and back piece. Normally we use white elastic to connect the chest to backplate under the shoulder straps Chest and back shall be connected with a white fabric or preferably elastic strap at the shoulders. As seen in the images from screen used armor below, this ideally must be approximately 2 inches (48 mm) wide.
-
Hello and welcome to the forum, for TD's head to MEPD https://forum.mepd.net/, Walt's armor is for ANH or ESB. As for accuracy there are other kits out there more accurate, but many are happy with their armor.
-
TK-23592 & TK-24269
-
4/20/24 - Walk MS Sent from my iPhone using Tapatalk
-
2/22/24 - Star Wars Night at Tampa Bay Lightning Sent from my iPhone using Tapatalk
-
Sent from my iPhone using Tapatalk
-
Sent from my iPhone using Tapatalk
-
Underside Sent from my iPhone using Tapatalk
-
Small update ended up cutting the last tab on the back strap problem is it’s now too short for the elastic to slide over the back plate unless I move it to the very last tab. I still have yet to do a test fitting so it may actually be better once it is actually on me. Luckily the black strap on the underside is holding the front and back plates together so hopefully this won’t be too much of an issue. Sent from my iPhone using Tapatalk
-
Darkspeed joined the community
-
Hello FISD. My name is Jason, I’m from Indiana and am about to start pursuing my dream of building a SANDTROOPER, with ATA out the picture I am currently stuck between RS PROPMASTERS and WALTS TROOPER FACTORY for my armor.
-
Good luck with your build,.
-
[12] TK-23072 Troop Log (Social Media Consent)
budu1 replied to budu1's topic in Field Training Exercises
Mision 12 24/05/2024 - MADRID - Fundación Alas Madrid -
Thank you!
-
Awesome, thanks for the tip!
- Last week
-
Byers changed their profile photo
-
Looks great so far!
-
I think I need a larger helmet
dblcross replied to Firemantrooper's topic in Hard Armor (General Discussion)
That's an achievement! I had to get contacts just for my bucket. -
ronhoffman2 started following I think I need a larger helmet
-
I think I need a larger helmet
ronhoffman2 replied to Firemantrooper's topic in Hard Armor (General Discussion)
I have the thinnest piece of foam at the top after having a thicker piece and the sight is so much better now and the neck part of the helmet doesn’t dig into my throat when i look down anymore. Sent from my iPad using Tapatalk -
For me 120 is a little coarse and I'd start with something around 180 or 240 using wet and dry with water. ABS paste can dry a different color compared to the ABS and you are sanding through the gloss finish of it. I had a similar issue with my TFU armor, I ended up using some waterbased acrylic paints and mixing to match the color of ABS and dabbing on in a few of the darker areas.
-
Who's Online (See full list)
-
Albums
-
Captain Enoch (Ahsoka)
- By themaninthesuitcase,
- 0
- 0
- 2
-
Promo pictures & others
- By Locitus,
- 0
- 35
-
Publicity Blaster - Nambu Type 99 LMG
- By gmrhodes13,
- 0
- 0
- 4
-
TFA F-11D Blasters
- By gmrhodes13,
- 0
- 0
- 13
-
Captain Phasma TFA References
- By gmrhodes13,
- 0
- 0
- 59
-