IceStormTK[TK] Posted December 1, 2015 Report Share Posted December 1, 2015 (edited) Name: Roy Ice Legion ID: TK-93500Garrison: Southern California GarrisonFISD ID: IceStormTK TK-93500Armor = RS Prop Masters Full CommissionHelmet = RSBlaster = RSHeight = 5' 10"Weight = 175Boots = RSCanvas Belt = RSHand Plates =RS Electronics = iComm TK Products Neck Seal = RSHolster = RS Lens Material = Trooperbay FRONT: BACK: LEFT ARM RAISED: RIGHT ARM RAISED: RIGHT SIDE DETAIL: LEFT SIDE DETAIL: LEFT SIDE (PAINT TOUCHED UP): ABDOMEN DETAIL: ACTION SHOT: COD AND BUTT PLATE ATTACHMENT: INTERIOR STRAPPING: HELMET FRONT, SIDES, BACK: HOVI TIP DETAIL: LENS COLOR: BLASTER, LEFT AND RIGHT: NECK SEAL: THERMAL DETONATOR (BACK): HOLSTER ATTACHMENT (FRONT AND BACK): Edited December 4, 2015 by IceStormTK Quote Link to comment Share on other sites More sharing options...
Bulldog44[TK] Posted December 1, 2015 Report Share Posted December 1, 2015 Looks awesome. Good luck. 1 Quote Link to comment Share on other sites More sharing options...
Altair[TK] Posted December 3, 2015 Report Share Posted December 3, 2015 Looks good Roy! A couple of very minor things I personally would look at.. The Terminal Det - if you are able to re-seat the control panel pad so it faces more upwards? Although not required, I would add some mesh behind the frown, i think it looks nicer Also slightly adjust the elastic strap on the left shoulder bell (the one that joins to under the shoulder straps) so it is uniform in length with the right side one. Good work mate 1 Quote Link to comment Share on other sites More sharing options...
WhiteRoseSwampy[TK] Posted December 3, 2015 Report Share Posted December 3, 2015 Looking good, another great set of RS armour. I agree that you shoulder bell elastics could be tweaked slightly 1 Quote Link to comment Share on other sites More sharing options...
IceStormTK[TK] Posted December 3, 2015 Author Report Share Posted December 3, 2015 Thanks John and Pete!<br> Yes, I definitely need to adjust the shoulder straps. That's what I'm tackling right after I finish my current usb rechargeable helmet fan experiment. I had to do quite a bit of resizing of this armor, especially the thighs, but I hope to have it ultimately fit like a glove. I'm also definitely going to put the mesh behind the teeth, I just keep forgetting to pick it up every time I'm at the hardware store. Duh. Also, thanks John for pointing out the thermal detonator. I hadn't even noticed that. I'll compare with the reference photos and adjust as necessary. Thanks again for your help! 1 Quote Link to comment Share on other sites More sharing options...
IceStormTK[TK] Posted December 3, 2015 Author Report Share Posted December 3, 2015 Looks good Roy! A couple of very minor things I personally would look at.. The Terminal Det - if you are able to re-seat the control panel pad so it faces more upwards? Although not required, I would add some mesh behind the frown, i think it looks nicer Also slightly adjust the elastic strap on the left shoulder bell (the one that joins to under the shoulder straps) so it is uniform in length with the right side one. Good work mate Looking good, another great set of RS armour. I agree that you shoulder bell elastics could be tweaked slightly Quote Link to comment Share on other sites More sharing options...
Snaps[TK] Posted December 3, 2015 Report Share Posted December 3, 2015 Good luck trooper! 1 Quote Link to comment Share on other sites More sharing options...
Sly11[Admin] Posted December 6, 2015 Report Share Posted December 6, 2015 Hey Roy, thanks for your application, so without further delay, here we go. CRL and EIB Application Requirements: All the required photos have been posted. Your armor contains all the necessary elements to qualify for EIB. With that, we would like to congratulate and welcome you to Expert Infantry. Congratulations!! Other-Armor Fit/Assembly: Commission builds are always interesting as you never know how they are going to fit until you first put it on. RS Prop have done a great job as the armor fits you well, but there are always going to be one or two little things that need fine tuning. As your fellow troopers have mentioned, those top straps on your Shuolder bells could be shortened so the Bell top touches the bridge. Centurion Suggestions: Your Ab and Kidney alignment were a topic of discussion between Tony and myself, so we did some research and a bit of digging as we wanted to ensure your best interest were in hand. We discovered that this alignment is standard with RS Prop commission builds, so the below comments and photo regarding this are only suggestions to make your armor look as accurate as possible and will not effect any future approval. Below this are also some suggestions for the positioning of the snap on the opposite side, Ab and Kidney alignment Your armor Alignment on a screen used set of armor Snap positioning on right side. The snap should be closer to the seam, where I have placed the Blue circle, this can be achieved in two ways. Either by trimming off some surplus material to the (Red line), or moving the snap to the(Blue circle) position, making some ABS paste and filling the old hole. This is a mod we would really like to see, if you have the extra space, trimming and shortening the internal straps would be the easier option. Photo of original armor right side snap postilion. You have a beautiful set of armor and should be proud, Congratulations once again, and we hope to see a Centurion application from you soon. 1 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted December 6, 2015 Report Share Posted December 6, 2015 Congrats trooper 1 Quote Link to comment Share on other sites More sharing options...
WhiteRoseSwampy[TK] Posted December 6, 2015 Report Share Posted December 6, 2015 Congratulations trooper, onwards to Centurion! 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.