Onlyalad19 Posted September 19, 2015 Report Share Posted September 19, 2015 (edited) Hello everyone! This will be my first attempt at building a ANH E-11 and I hope you all enjoy it. I had purchased the new Phoenix Props E-11 kit and I must say it is very impressive. We all know how a blaster kit looks unboxed and that resin parts should get a good wash before any work is started, so I will skip ahead and start this thread with some of the parts already repaired and prepped for installation. Also, please feel free to offer any helpful criticism along the way. I started with the end cap and wanted to make sure that when assembled, it functioned as a real Sterling should. As you can see, repairs were needed so the parts resembled the real thing. Edited September 19, 2015 by Onlyalad19 Quote Link to comment Share on other sites More sharing options...
I'm Batman[501st] Posted September 20, 2015 Report Share Posted September 20, 2015 Great start! Does the screw thread in the D-Ring retainer actually function? Quote Link to comment Share on other sites More sharing options...
Onlyalad19 Posted September 20, 2015 Author Report Share Posted September 20, 2015 (edited) The screw was actually added for strength. When the d-ring section is finally glued in place, it will look like one piece just like the real cap. Edited September 20, 2015 by Onlyalad19 1 Quote Link to comment Share on other sites More sharing options...
Twnbrother Posted September 20, 2015 Report Share Posted September 20, 2015 I like the screw idea. The rear piece that holds the D ring should be a little lower. It sticks up just a little bit. I will be watching your thread. Great start. Quote Link to comment Share on other sites More sharing options...
Thrawn's guard Posted September 20, 2015 Report Share Posted September 20, 2015 (edited) I'm looking forward to following your build Jared. I think that you'll find this forum very friendly and helpful so keep building and asking questions. Edited September 24, 2015 by Thrawn's guard Quote Link to comment Share on other sites More sharing options...
Onlyalad19 Posted September 20, 2015 Author Report Share Posted September 20, 2015 (edited) Thanks for the heads up Twnbrother. Here is where the d-ring now sits after a little adjustment. I think it looks much better now. So moving on with the build, I decided to focus on the gun sights next. The rear sight needed some minor repair and some drilling to expose the peep hole that was lost in the molding process. Now with the front sight I had to once again do some touch ups, but also put more effort into it to bring out the details... which is ironic considering the size of it. I very carefully used my Dremel press to drill out the hole and tap it for the 6/32 x 1/8" hex set screw (grub screw). As you can see it came out perfectly! Then with the same Dremel I used the sanding disc attachment and a flat needle file to make the channel along the bottom. Nailed it! Edited September 20, 2015 by Onlyalad19 3 Quote Link to comment Share on other sites More sharing options...
I'm Batman[501st] Posted September 20, 2015 Report Share Posted September 20, 2015 Sure did! Quote Link to comment Share on other sites More sharing options...
Onlyalad19 Posted September 20, 2015 Author Report Share Posted September 20, 2015 Here is another update for today. During the course of this project I somehow managed to lose one of the little resin half moons that came with the kit, so I had to make my own. I used a scrap piece of sheet aluminum, that luckily was the exact thickness, and bend it around a 3/4" o.d. steel tube. I then used masking tape to make a template from the remaining half moon and taped it onto the newly bend sheet. After using a cutting disc to cut out the basic shape, I then used a flat needle file to get them into the exact shape. Then I finished them off with a light sandpaper to remove any deep scratches and bring them to a nice shine. Making these little guys from scratch seemed like a very daunting task, but it was not as hard as it seemed. It certainly looks better and in the end will be much stronger than resin. That is all for today! 1 Quote Link to comment Share on other sites More sharing options...
charlesnarles Posted September 21, 2015 Report Share Posted September 21, 2015 Flash guards look great for hand-made. Keep up the good work Quote Link to comment Share on other sites More sharing options...
Tr00per Posted September 23, 2015 Report Share Posted September 23, 2015 (edited) Keep it up, it looks very sharp OT question: Does anyone know why the rear sight wasn't flipped over when casted ? It would help out allot of people gluing them the wrong way around most of the time. Edited September 23, 2015 by Tr00per Quote Link to comment Share on other sites More sharing options...
Onlyalad19 Posted September 24, 2015 Author Report Share Posted September 24, 2015 Thanks for the kind words everyone! I should have another update in a couple of days, so stay tuned. Quote Link to comment Share on other sites More sharing options...
usaeatt2 Posted September 24, 2015 Report Share Posted September 24, 2015 During the course of this project I somehow managed to lose one of the little resin half moons that came with the kit, so I had to make my own. HOLY $#@%!!!! I don't always use profanity, but when I do, you better believe it's because this project RULES!!! Dang Jared, those are BETTER than any original guard I've ever seen! Stellar work, man!! Quote Link to comment Share on other sites More sharing options...
Dday[501st] Posted September 24, 2015 Report Share Posted September 24, 2015 Keep it up, it looks very sharp OT question: Does anyone know why the rear sight wasn't flipped over when casted ? It would help out allot of people gluing them the wrong way around most of the time. I've got rear sights molded for the sight at the 100 and the 200 mark. I've never been able to get a real answer on weather it was one or the other. With the sight at the 100 mark, it gives the exact height (I feel) for the scope rail. With the sight forward at the 200 mark, it gives a very nice guide to drill the hole down for the scope rail. What really matters though is that the ribs on the sight face back towards the wielders face. Quote Link to comment Share on other sites More sharing options...
Onlyalad19 Posted October 5, 2015 Author Report Share Posted October 5, 2015 Update time! Since I wanted this build to be a screen accurate prop replica, I wanted to incorporate as many real parts as possible. Here is what I have so far. Quote Link to comment Share on other sites More sharing options...
charlesnarles Posted October 6, 2015 Report Share Posted October 6, 2015 FYI this is on sale <br> <a data-ipb='nomediaparse' href='http://www.apexgunparts.com/sterling-l2a3-smg-parts-set-9x19-nato-4905.html'>http://www.apexgunparts.com/sterling-l2a3-smg-parts-set-9x19-nato-4905.html</a><br> You'd probably be able to work with any sloppy weld-cuts, eh? Quote Link to comment Share on other sites More sharing options...
Onlyalad19 Posted October 7, 2015 Author Report Share Posted October 7, 2015 Thanks for the link Scott, but sadly I have zero skills when it comes to welding. Plus, these parts will add that extra bit of detail that I wanted without the extra work... especially when it comes to the folding stock. Quote Link to comment Share on other sites More sharing options...
Onlyalad19 Posted October 7, 2015 Author Report Share Posted October 7, 2015 Today I worked on the magazine catch assembly installation. First step was to drill a hole completely through the magazine for the shaft of the push button. Then using a 1/4" diam. bit I set the depth on my Dremel press and carefully routed out the space for the bottom catch plate. Here it is after going back and forth a few times to make sure it fit correctly in place. After the fit was finalized, it was just a matter of installing the parts to make sure it all functioned. This was a fairly easy part to install since the kit was cast from a real sterling. I have seen other builds where this assembly was made from scratch and had it look just as good, but I went the easy route to save myself the headache. 2 Quote Link to comment Share on other sites More sharing options...
usaeatt2 Posted October 7, 2015 Report Share Posted October 7, 2015 You know you're doing it right when I have to scrutinize closeup pictures twice to actually believe this is a resin build... BEAUTIFUL WORK. 1 Quote Link to comment Share on other sites More sharing options...
Dday[501st] Posted October 7, 2015 Report Share Posted October 7, 2015 Very nice! IT's awesome you're adding in these additional things to make this a very accurate build! 1 Quote Link to comment Share on other sites More sharing options...
Thrawn's guard Posted October 7, 2015 Report Share Posted October 7, 2015 Jared - You have carried out some really impressive work here with great attention to detail. I particularly like what you have done with the magazine catch assembly. As I have said before I am constantly amazed at the continued improvement on modifications that can be made to resin kit builds this build being a prime example. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.