TK-27639 Requesting ANH-Stunt Centurion Status [RS][209]

[ZARAL[TK]]

Name: Alberto Lanz
TK: 27639
Forum Name: ZARAL
Garrison: Spanish Garrison
Armor Maker: RS Prop
Helmet Maker: RS Prop
Blaster Type: Doopy Doo´s

Height: 1´84 m
Weight: 75 Kg
Boots Maker: RS Prop
Canvas Belt: RS Prop
Hand Plates Type: RS Prop Latex
Neckseal Type: RS Prop
Holster Maker: Spanish Garrison´s Member
​

EIB Thread:http://www.whitearmor.net/forum/topic/31187-tk-27639-requesting-anh-stunt-eib-status-rs-prop461/?hl=zaral

 

​

​

​

​

​

​

​

​

​

​

​

​

​

​

 

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

 

 

Thank you for your consideration,

 

ZARAL --- TK-27639

Edited January 16, 2016 by ZARAL

[68Brick[TK]]

Looks Good!

[Sly11[Admin]]

Hi Alberto, Tony and I are reviewing your application, please stand by.

 

 

Sent from my iPad using Tapatalk

[Boltstrooper[TK]]

Nice built.  Good luck with submission.

Edited December 9, 2015 by Boltstrooper

[ukswrath[Staff]]

Hi Alberto, sorry for the delay, thank you for your application so lets take a look.

 

CRL and Centurion Application Requirements:

All photos are present, including the extra couple we requested, first let me say your armor look wonderful, but there are a few things that need a little bit of attention, your almost there.

 

1. For Centurion, as per the CRL we require there to be virtually no gap between the Ab and Kidney plate. Now we weren't  quite sure if the gap was caused when you raise your arms, hence the request for a couple of extra photos. This much gap on both sides is fine for EIB, but  we'll need you to reduce it for Centurion please. This may very well close if you tighten your belt is a bit, or perhaps shorten any straps you may be using eliminating the need to make shims on the sides.

 

 

Here's a screen shot

 

 

2. There is a lot of attention to detail in your armor, so we think a little bit of black paint on the screws heads of your Thermal Det will be a perfect finishing touch.

 

Here's a reference pic

 

 3. Your drop boxes look like they can move around a bit too so maybe a small piece of Velcro will stop that from occurring.

 

 

4. And lastly sniper plate to shin alignment. Your sniper plate is aligned with the ridge on one side, which is spot on, however the opposite side is attached below the ridge. You may be concerned that by moving it, it will look crooked, but trust us when we say many of them are even when aligned properly, and that's ok.

 

 

This is where it should sit in alignment with the ridge. Here's a screen shot

 

 

 

You are only a few steps away from Centurion, complete the above mentioned modifications and re submit the photos of the adjustment and you will be good to go.

[ZARAL[TK]]

Hello!

I re submit the potos. I re submit two explanatory photos about my drop boxes because it can´t move when i put the bult.

 

I hope all is well now.

 

Thank you very  much.

[ukswrath[Staff]]

Thanks Alberto we'll be with you shortly

[ukswrath[Staff]]

Hey Alberto thanks for the corrections and updated images. We're still struggling with the drop boxes but this time it's that they are sitting too high or there too much lower return edge on the ammo belt. You should have 1-2mm return edge below the ammo boxes and the drop boxes should sit even or slightly below that.

 

Here's a reference picture.

 

 

Take care of that and we'll get you Centurion approved.

[ZARAL[TK]]

I understand now what you meant. I get to work.

Thanks.

[ukswrath[Staff]]

I understand now what you meant. I get to work.

Thanks.

 

Thanks 

[ZARAL[TK]]

I added two photos. I hope all is ok now.

 

Thanks.​

​

[ukswrath[Staff]]

Hey Alberto, close brother but the drop box alignment needs to be more like this. Aligned with the end of the belt also.

 

Thanks

 

[ukswrath[Staff]]

Also, please add a link to your EIB app page at the top of this app. Thanks again

[ZARAL[TK]]

Hello!

I added a link to my EIB and a new photo.

Thanks.

[ukswrath[Staff]]

Great job Alberto! Thank you for your Centurion application and thank you for making the required repairs.

 

CRL and Centurion Application Requirements:

All required submission photos have been posted. Your armor displays all the necessary requirements to qualify for Centurion.

Sly and myself would like to congratulation and welcome you to Centurion! Excellent job!   

 

Other-Armor Fit/Assembly:

In this section we'd like to take a moment to suggest armor adjustments made by your fellow troopers or Sly and myself. One area that could use a little TLC is the sniper plate. Trimming the lower edge nearest the shin so it follows the contour of the shin armor itself. Removing the little flare at the end would give the area a cleaner and maybe even help prevent it from getting caught on something.

 

 

Rounding off the thing ammo pack corners would make that area look a bit cleaner also.

 

 

Great job trooper, now get out there and represent your garrison and the 501st proudly.     

[ZARAL[TK]]

A lot of thanks. I'm very proud!!!

Edited January 18, 2016 by ZARAL

[WhiteRoseSwampy[TK]]

Congratulations Centurion!

[Captain_Wordo[TK]]

Congrats Alberto and welcome to the centurion rank!

[fokker210[TK]]

Nice work Centurion!