Sparrow Posted June 9, 2012 Report Share Posted June 9, 2012 Name = Steve Goldsack Garrison = OuterRim Squad, Badlands Garrison Forum name = Sparrow Stormtrooper, A New Hope, (Hero) Height = 6' 2" Weight = 180 pounds Armour = SDS - heavily modified/trimmed/reshaped Helmet = SDS - upgraded bubble eyes and hero ears from John Danter TK8456 Hero Upgrade Kit Blaster = SDS - added D ring Boots = TK Boots Hand Plates = SDS Outer Gloves = Nomex Flight Gloves Thermal Detonator = Jesse TK4702 Thermal Detonator Canvas Belt = TKittell TKittell White Canvas Belts Electronics= Aker 12 watt amp / I-Com / Memorex wireless mic from TK6294 Akers/ICom/Wireles Neck Seal= Veedox Veedox ANH Hero Neckseal (Neck Seal from “Lady Sew for Us†is pictured) Holster= Darman TK9356 Darman ANH TK Holsters Build Thread: ANH TK Build Hero in Uniform Hero out of Uniform I couldn't resist! Required Costume Components FISD Defines two additional, optional levels of costuming excellence: Expert Infantryman and Centurion. Expert Infantryman is listed in black. Centurion requirements are in red. Helmet •Traps/tears and tube stripes shall have the correct ANH TK details. •Lenses must be green bubble or smoke bubble only. •Tears/traps shall be hand painted or use decals that emulate hand painted (with correct ANH TK details). •Correct 'Hovi mic' aerator tips. •Ears shall have two screws per side, one above the ear bar and one at the base of the helmet. •Ear bars should have three bumps only, not four. •Ear bars shall have only one or two bumps painted in black (rank stripes). •Neck trim shall be of an s-type profile rather than a u-type profile. Shoulder Straps •These shall be glued in front. •These shall free float in back. •The plastic shoulder straps need to be held down in the back via a white elastic band to the white fabric that connects/bridges the chest and back piece. Forearms •No return edge on the inside of the front of the forearm is allowed. Hand Plates •Hand guards shall be latex or latex-like, painted white, affixed to rubber gloves in lieu of plastic hand guards. Gloves •Gloves shall be rubber or rubber-like chemical gloves, in black. Chest •Chest and back shall be connected with a white fabric or preferably elastic strap at the shoulders. Back •Back plate shall have no, or minimal overlap of the kidney plate. Abdomen Plate •Any gap between the ab and kidney plate shall be no more than 1/2" (12.5mm) wide. •Ideally there should be no gap between the ab and kidney plates, just a single visible seam line. •Rivets on the left side of the ab plate: a total of three rivets, the heads should be approximately 5/16"(8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. •A single male snap on the top right corner of the ab plate shall be present. •A single split rivet or brad shall be present on the crotch tab of the ab plate. It does not need to be functional. Kidney Plate •A separate kidney plate shall be present, split from the butt plate. •Three rivets shall be present on the left side of the kidney plate, the heads should be approximately 5/16" (8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. Butt Plate •Two male snaps shall be present on the crotch tab of the butt plate. They do not need to be functional. Belt •Belt shall be canvas or canvas covered, leather and vinyl are not acceptable. •There shall be three square buttons, one centered in the middle and one on each end of the plastic ammo belt. •The corners of the plastic ammo belt shall be trimmed at a 45 degree angle. •Drop boxes are closed in the back. Thermal Detonator •The thermal detonator needs to be attached via metal clips approximately 1"(25mm) wide, and shall be all gray without silver stickers or silver paint. Thighs •The thigh ammo belt shall be connected by brads/split rivets only – but not by standard rivets. •The bottom corners of the thigh ammo belt shall be rounded off. Lower Legs •Ideally there should be no visible rivets or brads used to secure the sniper plate to the left greave. Boots •Boots shall be lightly scuffed. Holster •Holster shall be worn on the left and be attached to the belt from behind instead of front, with no loops covering the outside of the belt. •The holster shall be affixed with four fasteners (two at the top and two at the bottom of the belt) instead of none or two. These may be rivets, snaps, or Chicago screws. BlasTech E-11 •Folding stock (does not need to function). •A real or replica ammo counter - based off of a Hengstler counter - shall be present. •D-ring mounted on the rear. •Correct style scope. •Two power cylinders on the magazine housing. Additional Options Imperial Communication System (I-Comm) Split Cod Profile shots Action shots Quote Link to comment Share on other sites More sharing options...
BananoPower22[TK] Posted June 9, 2012 Report Share Posted June 9, 2012 I think this is the best request thread I've ever seen. Amazing! Quote Link to comment Share on other sites More sharing options...
Sparrow Posted June 9, 2012 Author Report Share Posted June 9, 2012 Thank you! Great Costuming is all about the details! Quote Link to comment Share on other sites More sharing options...
Guest TKrat Posted June 9, 2012 Report Share Posted June 9, 2012 Agreed! Great build Quote Link to comment Share on other sites More sharing options...
SCTrooper[TK] Posted June 9, 2012 Report Share Posted June 9, 2012 The armor fit's you well. I really like the first action shot. The mod's you made to the armor look nice. Cheer's Nick Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted June 10, 2012 Report Share Posted June 10, 2012 Looks good. Approved! Quote Link to comment Share on other sites More sharing options...
Dazauto[TK] Posted June 11, 2012 Report Share Posted June 11, 2012 Congrats Steve, great build and your armour looks awesome Welcome to the EIB ranks trooper Quote Link to comment Share on other sites More sharing options...
Faie[TK] Posted June 11, 2012 Report Share Posted June 11, 2012 Congrats Steve, good job!! Quote Link to comment Share on other sites More sharing options...
Sparrow Posted June 12, 2012 Author Report Share Posted June 12, 2012 Thanks guys! I had it done some time ago, just took a while to getting it done. It feels great to look great! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.