-
Posts
2,183 -
Joined
-
Last visited
-
Days Won
11
Content Type
Profiles
Forums
Gallery
Articles
Media Demo
Posts posted by Frank75139
-
-
Without fail I always forget the neck seal and have to take something off to put it on
Sent from my iPhone using Tapatalk- 5
-
Congrats!
Sent from my iPhone using Tapatalk -
Paint looks great. Nice job.
Sent from my iPhone using Tapatalk -
Your on the right track, good luck with everything.
Sent from my iPhone using Tapatalk -
Party time!!!!
Sent from my iPhone using Tapatalk -
Just as an added note Trooperbay’s one piece has dual zippers so you can still go to the bathroom but honestly it’s a pain in the butt no matter what you have on cause plastic armor doesn’t have zippers. I agree with the going cheaper cause I’ve already found that compression wears easily. My Tommie Copper set was bought with a really good deal and it’s truly amazing but if I didn’t get the deal again I can’t see spending that much money on compression. Trooperbay’s was less expensive ($100) and seems like it’s less likely to wear due to rubbing. Starting out I’d get a cheap set from Amazon and see how you like it. You can always switch up at a different time. And I actually went over the logo on my two piece with black permanent marker, it helps but it’s not permanent.
Sent from my iPhone using Tapatalk -
Welcome Jim
Sent from my iPhone using Tapatalk- 1
-
Took me a few minutes to figure out what stripes you were talking about but I’m on the right page now. I’m in no means an expert on the commander or anything for that point but I looked at the CRL and it looks like the top stripe goes across the the area of the foot where the leg curves into the foot around where the heel starts on the bottom. For the front stripe I’d just come off and inch or two maybe. Honestly it’s not stated in the CRL so I’m assuming nobody knows exact measurements but one would use a best guesstimate.
http://databank.501st.com/databank/Costuming:TK_commander
Sent from my iPhone using Tapatalk- 1
-
I have two sets. A one piece from Trooperbay and a two piece Tommie Copper. I think I’m more partial to the two piece. I feel it is a lot lighter and cooler then the Trooperbay one, it’s also easier to get into when it tight spots like changing in small bathrooms. Neither are thermal but since the Trooperbay one is heavier I mostly use that when it gets a little cooler.
Sent from my iPhone using Tapatalk -
Welcome aboard. So far you’ve got everything lined up ready to go.
Sent from my iPhone using Tapatalk -
Okay Kris, in the interest of the March to 1000 - a free moose patch when EIB is achieved.
Your a real company guy!
Sent from my iPhone using Tapatalk
-
Nice work
Sent from my iPhone using Tapatalk -
I´m a little short to dunk - wanna help out:dancing-trooper:
I’ll bring the trampoline
Sent from my iPhone using Tapatalk
- 1
-
Say what now?
I knew the video was floating around somewhere. Every time I see it I hope it’s an extended version which includes a slam dunk during a 5 on 5 TK pick up game.
Sent from my iPhone using Tapatalk
-
Bells- I agree lol Only issue I have with is I used to work out a lot and my shoulder muscles are still rather big even though i don't work out anymore lolz. What do you recommend I do to shape them differently to fit better. heat them up? that makes me nervous. the inside of the bells are just to tight.
Thighs- and calves are VERY close together and NO i cannot walk very well. I kept everything the size it came out of the box. can I just use a dremmel to shave down some? on top or near the knee?
Thanks again!
My opinion is move the bells closer to the shoulder bridges and see how that works (marked in red)
You can also shave down the tops of the thighs (blue) to raise them up and give you a bit more knee room to walk, just stay with the natural contour. I wouldn’t go too crazy just yet because you still have to velcro the calves which might help a bit.
You’ll notice the stock CRL photo has some black around the knee (green), I know some purist say go for minimal black showing everywhere but I’m a firm believer if your not comfortable your not gonna want to wear this for hours on end and you will be walking a lot. You can also see on the back of the CRL pic the calf and bottom rear thigh are cut slightly curved to help bend the knee. So my opinion would be when you get the velcro do another test fit and if it’s still not better then I’d personally adjust the length a bit.
Sent from my iPhone using Tapatalk
- 1
-
Hey Jared, looks good. Only glaring thing I see is your shoulder bells are too far out. They need to be closer to your body/shoulder bridges. Other then that it’s hard to tell but maybe realign the arms. Your thighs and calves look very close, can you walk in that thing?
Sent from my iPhone using Tapatalk
- 1
-
Lookin good!
Sent from my iPhone using Tapatalk- 1
-
Well done!
Sent from my iPhone using Tapatalk- 1
-
I got a roll of it with sticky back on it. Did the full length so of the top gets loose there is 3/4 left to hold it.
Sent from my iPhone using Tapatalk -
Brickfest!
I’ll be there Sunday morning
Sent from my iPhone using Tapatalk -
If we look past the fact that AJ was done first, it’s perfect! Great job on it. Armor is always a work in progress so get it submitted and approved.
Sent from my iPhone using Tapatalk -
Welcome. And FYI I’m in Philly (Garrison Carida) and there is an active community, smaller then where your at now, but a community in this area. If you ever feel like coming back and trooping around your old area we’d love to have you.
Sent from my iPhone using Tapatalk -
I find velcro works very well. I’m sure at some point it’ll have to be replaced cause velcro wears thin but you can deal with it then and it’s not that hard to replace.
Sent from my iPhone using Tapatalk- 1
-
I see what your saying. None of them really flow well. I like the idea, there has to be a way.
Sent from my iPhone using Tapatalk
TK Stunt Neck Trim
in The Replica Section
Posted
So I’m gonna throw this out there and see what people think or already know.
I recently replaced the neck trim on my stunt and the one I got was considerably smaller and easier to work with. I don’t remember where I got the first one but with the smaller one it makes getting my head in so much easier. Is there, or has there ever been any talk as to what the size of the trim was? I only knew the ones size that was listed as a “TK neck trim”. This is purely a question out of curiosity, I in no way want to start something that’s gonna push into any CRL changes.
Sent from my iPhone using Tapatalk