Jump to content

Sgt. Bilko

501st Stormtrooper[TK]
  • Content Count

    79
  • Joined

  • Last visited

About Sgt. Bilko

  • Rank
    Centurion

Profile Information

  • Gender
    Male
  • Location
    NW Indiana

FISD Info

  • Centurion Granted Date
    20170518
  • EIB Awards
    1
  • EIB Cohorts
    ANH-S

Standard Info

  • Name
    Scott
  • 501st ID
    80704
  • 501st Unit
    Northern Darkness Garrison

Recent Profile Visitors

185 profile views
  1. Hi Guys, Any thoughts on adding TFA TK to the vetted list? Forgive me if this has already been asked, but reading through 53 pages in the morning...not enough coffee to get this done! I'm thinking there are three...Anovos, Jimmi and KBP. I'm writing this, as I am considering a TFO build and am starting my research from scratch. Having this list would be helpful. Thanks, Scott
  2. Hi Omar, Thanks for starting this thread. While Anovos is not accredited with the Better Business Bureau. It seems as if there have been enough complaints against them for them to be rated an F. Seems like they need some serious focus on customer service. For anyone else...who else makes vetted FOTK armor? Sent from my iPhone using Tapatalk
  3. How much are Anovos shipping charges within US? Says it's handled separate of the initial order and billed later in. Sent from my iPhone using Tapatalk
  4. Paddy, some helpful fit advice from a fellow RS owner. The thighs look like they could be dropped a bit, or need to be shortened. From a fit standpoint, the butt plate overlaps the thighs. Has to be tough to walk in. No? Love the ESB armor...jealous! Sent from my iPhone using Tapatalk
  5. Good point Paul. For the record, I had the same issue with my RS build and thigh pack. Joe sent me split rivets within a few days and the replacement was quick and easy. Check out my EIB app to see the results. Sent from my iPhone using Tapatalk
  6. Scott Bilkey 80704 EIB Letter size - Tony http://www.whitearmor.net/eib/certificates/80704-eib.png Sent from my iPhone using Tapatalk
  7. Thousands of years of technological advancement with giant lasers to blow up entire planets and they can't find a better way to power the Death Star? Sent from my iPhone using Tapatalk
  8. TK-80407 Requesting ANH Stunt EIB Status [RS] [708] https://r.tapatalk.com/shareLink?share_fid=44557&share_tid=41105&url=http://www.whitearmor.net/forum/index.php?/topic/41105-TK-80407-Requesting-ANH-Stunt-EIB-Status-%5BRS%5D-%5B708%5D&share_type=t Sent from my iPhone using Tapatalk
  9. To get to Centurion, you may need to make more than sizing adjustments. For my commission, I had to replace rivets, trim edges, heat gun and reshape the buns (still not perfect). I also made mods to the helmet, adding some electronics. Have a look at my EIB submission. Post your first suit up and take lots of pictures. Your plastic spaceman journey begins! Sent from my iPhone using Tapatalk
  10. Congrats Frank....rocking the RS armor well. See you at EIB! Sent from my iPhone using Tapatalk
  11. Thanks nukem. I went with 20x20mm and it looks good. Compared to the centurion submittals. Appreciate confirmation though. Sent from my iPhone using Tapatalk
  12. Beuhler, Beuhler, anyone, anyone...LOL! I followed up on some of Ukswrath's builds....since his build and seamlines look identical to mine, I went with the following guidance. Thread: http://www.whitearmor.net/forum/topic/35086-ukswraths-anovos-tk-build/page-20 4f. Ab Right side rivet assembly In this section I'll install the Centurion required male snap found on the upper right hand side of the ab. Note: The Centurion required snap does not need to be functional. From the top right corner measure 20mm vertical and 20mm horizontal from the outer most return edge
  13. Good morning....a few updates on the ABS paste work. I created the paste and initially found it to be too runny. I let sit for a full day and the consistency became like toothpaste. Using the process above, I filled the hole. Pics below: Snap Hole Before Work Begins: I sanded the area with 400 grit to allow the paste to adhere and covered the areas around the hole with painters tape. I placed a temp piece of ABS on the back of the hole to support the paste whilst it dries. After the ABS dried, i removed the painters tape and allowed to dry overnight. I'm sanding down today and will show some final pictures later on. I was curious if anyone had a response to my previous post. Do I put the new snap in the 12mm x 12mm position shown?
  14. Working on my Centurion punch list

×
×
  • Create New...