Jump to content

Recommended Posts

So this is where I will be logging my T-21 build for my Rogue One Kit. Not a lot of stuff at this time but I am sure I will  be filling this thread in the coming weeks. So first let me say that I will be using Spool86's kit.

 

For anyone interested, my ROTK build is here: 

 

 

And my RO Crystal Patrol Pack Build is here: 

 

 

There are a few difference with the RO variant of this BFG. 

1. There is a scout tactical light on the right side like a lot of the RO weapons.

2. I have found reference pictures with a black sling and pictures with no sling.

3. From all the pictures I have found, the stock looks black but this could be the lighting.

 

Here is a pic with the black sling

 

VCN1nAM.jpg

 

I will add more pics tomorrow but I wanted to get this thread started. 

 

I welcome input from everyone. 

 

Thanks for the interest.

 

 

  • Like 3

Share this post


Link to post
Share on other sites
11 hours ago, ukswrath said:

:popcorn:

Thank you

Share this post


Link to post
Share on other sites

Ok so here is another shot of the previously posted picture. The sling looks black to me and the stock does as well. Also notice that the sling is mounted with a sling mount in the front top side of the barrel rather than being wrapped around the barrel. In another shot (I have somewhere) of the same TK the rear end of the sling is also mounted to a sling mount that is mounted to the left side of the stock.

 

3koAXl0.jpg

 

Here is a shot I found that this T-21 has no sling and the stock does look to be slight dark brown but again it could be the lighting.

 

rbbR017.jpg

 

Guys feel free in your copious amount of free time to find more reference pics from Rogue One of behind the scenes pics that have T-21s in them and post them. I am unsure which direction to go with the stock and may settle on an Ebony stain for the stock.

 

Spool86’s parts are hitting my mailbox today so I should get started on building this thing this weekend.

 

For the barrel I like what Yosh did with his build and just about everyone agrees that the PVC pipe is the heaviest part of the T-21; however, I think I may have an idea to sue the PVC pipe but lower the weight. I am hoping to put it on my lathe and take about ½ the weight down by cutting the groves in it like the actual Lewis barrel shroud (red circle).

 

AItQdbb.jpg

 

So that is it for the update.

Thanks for the interest.

Share this post


Link to post
Share on other sites

I would start with identifying any differences (if any) between the OTTK T-21 and the ROTK. I can see several just from the photos above. 

Share this post


Link to post
Share on other sites

ukswrath, I see the stock color, flash light, sling and mounts, looks like a tall rear sight between the barrel and the receiver. What else do you see?

Share this post


Link to post
Share on other sites
42 minutes ago, 11b30b4 said:

ukswrath, I see the stock color, flash light, sling and mounts, looks like a tall rear sight between the barrel and the receiver. What else do you see?

I'll look at so high res stills when I get home but so far those you mentioned are what I see also.

  • Like 1

Share this post


Link to post
Share on other sites

Ukswrath, were you able to glean any further details? I would really like more information about the shape and design for the big sight midway down the gun.

 

Update,

Ok so let me first say that before I started this build I did message Hyperfirm twice about pricing for a Rogue One T-21 with no reply. I figure they would be around $300.00. So based on that price, it is questionable if I would have been better to just buy one. After the $100.00 Spool86s kit, the knock off surefire scout light $40.00 and all the stuff I got from Home Depot and Lowes $200.00 ish I am already over the $300.00 price point; however, I get to build something and that cannot be quantified.

 

Ok so here is Spool86’s kit and me doing some test fitting. I will say that I am glad I got this kit however, there are some things that I wish to change about the kit. I am basing my build somewhat on Yosh’s build and like him, I will be modifying Spool86s kit. Spool did an amazing job with this kit and nothing I say here should be interpreted as a criticism of his kit in any way.

 

7wj2DFt.jpg

 

Test fitting the kit, I learned a few things. First the cooling fins seem to be sized for 3” (thin walled) waste water pipe rather than cellular core schedule 40 3” pipe. Both pipes have a 3” inside diameter but the outside diameter is different. Here you can see the cooling fin is not large enough to cover the edge of the schedule 40 pipe.

 

enq7uqL.jpg

 

The opposite seems to be the issue with the muzzle fins. Here you can see that the outside of the fins are larger than the inside diameter of the 2.5” electrical conduit.

 

Zv9E3Fl.jpg

 

Looking at several reference pictures of an actual Lewis, I decided to cut down the feed tray.

 

ZxnfJJU.jpg

 

2dn2zQ5.jpg

 

So one of the priorities I have set for this build is to make it as lite as possible. I may, at a later date, make a mold and cast this in rubber but for now, I wanted to just get it built and be as true to what I want as possible. So for the main support I chose to use ½” sanded plywood. I had considered several other options like making the center out of fiberglass or using a solid piece of wood but the strength of plywood cannot be questioned and it is hard to come up with something that is as easy to work with and as strong without it weighing a lot more.

 

So I got a 2’ x 2’ piece of plywood and using panadatroopers template, drew out the shape.

 

TMbhDrg.jpg

 

I decided to cut down the side receiver parts from Spool86s kit and make the chamber and bolt parts from PVC. This reduced the weight of these parts by about ½ and allows me to make the bolt look more realistic. Laying out the parts on the center support, I noticed an issue.

 

aCMID9S.jpg

 

If I stick with the schedule 40 pipe for the barrel, the cooling fins will not line up properly. On the bottom they look good.

 

DDdLuBw.jpg

 

However, on the top the fins are not tall enough (red circle). Also because I cut down the feed tray, the center section of the support plywood is now 3/8” too short.

 

Is1DC2f.jpg

 

So back to the hardware store I went and I purchased another 2’ x 2’ piece of plywood. I also picked up a 10’ section of the 3” waste water pipe. Home Depot did not have the pipe but Lowes did. So I retraced the support on the plywood but this time I added to the height of the receiver (where the feed tray would sit) and made a few other tweeks. Unfortunately, the 1” spade bit that I used to make the trigger opening bust out the bottom of the trigger guard. Honestly, I did not have high confidence that this thin section of the plywood would hold up for trooping so loosing this is not a huge deal. I had some ¾” wide and 1/8” thick aluminum in my shop so I needed to fabricate a trigger guard.

 

FarliTn.jpg

 

A lot of cutting, bending and sanding later I had something that would work.

 

cTRwlS1.jpg

 

Here is a side by side comparison of the 3” waste water pipe (Left) and the schedule 40 3” cellular core pipe (right). As you may expect the thinner pipe is liter by about ½ the weight. So no brainer, I’m going with the thinner walled pipe.

 

xeDkMeO.jpg

 

I cut down Spool86s trigger. I routed out the insert of the support plywood and mounted the trigger with a spring. I also figured out how I would mount the trigger guard. A screw on the forward part and a nail (top of picture) used as a pin in the grip area.

 

PoFymNl.jpg

 

And around this time I was banging my head on how I would make the transition from the 3” pipe to the 2.5” pipe. Most people do this with a buildup of bondo but I wanted something different so I built a 3D model of the transition. This model is designed to be a sleeve that will fit inside the 3” waste water pipe and the ¾” wide collar then the 2.5” pipe slides into a channel at the other end of the transition.

 

I designed this to only work with these pipe sizes:

Waste Water 3” pipe ID 78mm OD 82mm

Barrel Collar ¾” wide ID 83mm OD 89mm

2.5” Electrical Conduit ID 62mm OD 73mm

 

The transition will be 60mm tall when assembled with a top opening of 73mm and the bottom opening of 89mm.

 

So for anyone who wants this transition, please understand that it is still a work in progress; however, it is available for free download on my Thingiverse page.

https://www.thingiverse.com/thing:3070308

 

Here are some pictures of the transition.

This is it being printed.

 

FyzbItX.jpg

 

Here is a test fit.

 

nj7fN1c.jpg

 

The top.

 

M6IY3dX.jpg

 

The side.

 

NHCSvLS.jpg

 

So feel free to grab this model if you have use of it.

 

Next I sprayed primer on the support then I went in with Bondo to fill some of the gaps.

 

9gwvXcM.jpg

 

sYIhBM1.jpg

 

I also started the stock. I forgot to take more pictures as I built it but basically I used two pieces of 1” thick poplar wood. Poplar is a hard wood (but it dents easily) and it weighs less than pine or oak. So I traced out the stock on both halves of the poplar, then I routed out the insert hole for the plywood support. Next I routed out the center of the stock to shed some weight. I basically kept about ¾” around the edges untouched then routed about ½” deep from the center area on both parts. Then I glued and clamped the two halves together and let it sit overnight. Now I am shaping the stock with various sanding drums and sanders.

 

AVNTWQ7.jpg

 

The flashlight and D- gasket tube came in on Sunday.

 

pehT0gK.jpg

 

So in a previous post I said that I wanted to replicate the milling marks on the outside of the barrel like an actual Lewis barrel shroud. However, that was before I realized two issue. First, moving to the waste water pipe, the wall thickness is only 2mm thick and milling anything from the pipe will weaken it considerably. Second, the maximum length I can mill in my lather is 20 inches and this does not take into account the center and 3 jaw mandrel. So I would need to make the barrel portion 18” rather than 19” to mill it.

 

Another issue I did not consider is that the PVC pipe would not mill like other plastics. It basically develops a rough “hairy” face on the area milled. This can be cleaned up with sanding but a lot of the detail of the tooling would be smoothed in the process.

 

This is from one 18” pipe.

 

y9xB7bI.jpg

 

And even after milling about 1mm (1/2 the thickness of the pipe wall) this is the only detail I was able to produce.

 

Jp5ZP8m.jpg

 

This is a picture of the wall thickness of this pipe.

 

CM4J54e.jpg

 

So to produce the milling on the barrel, I will need to find another solution or drop the idea all together. Something to ponder.

 

Well that is it for the update. Thanks for the interest.

Edited by 11b30b4
  • Like 1

Share this post


Link to post
Share on other sites

I was sick all weekend, I'll try again tonight

  • Like 1

Share this post


Link to post
Share on other sites

Update…

Well Imgur was down yesterday so I could not post pics from Monday until now.

 

Ok so I sanded primed and painted the chamber tubes.

 

2fHBAMf.jpg

 

Here is a test fit of the bolt already painted with metallic silver.

 

49KaIMI.jpg

 

So for the barrel parts and getting the desired milling lines effect. Looks like 80 grit sand paper used on the barrel while it spun on the lathe did the trick. Here are some pictures of the 2.5” conduit tube.

 

BRUonO9.jpg

 

zAJebfu.jpg

 

And the 3” barrel tube.

 

6oPUEv2.jpg

 

iBN7wOf.jpg

 

Barrel parts, I still need another collar, possibly two.

 

mdNT6x5.jpg

 

As you can imagine, the lines in the tubes are not very deep so I do not know how well they will show once the parts are painted. I may paint them then re-sand them then apply a final paint job to bring them out more.

 

I decided to cut down the outer edge of the cooling fins to allow them to drop inside the 3: barrel pipe.

 

CqCL0mF.jpg

 

I made the top adjustment knob for the rear sight out of two brass lamp nuts, a small piece of lamp all thread, and a smaller nut that is adhered inside the all thread with PC-7. Once it is cured, I will sand and see this will work.

 

YoaVM0q.jpg

 

NoE6Ilf.jpg

 

Ok so I have been doing some research and discovered these pictures of aerial Lewis Gun configurations. I am thinking that the tall sight on the Rogue One T-21 is a modified Aerial gun sight. This first picture is the sight I think I will attempt to replicate and modify so that it is not as tall. The rest of the pictures show the vast array of sight options that were used in WWI and WWII.

 

IAt7QsP.jpg

 

5HuI4aY.jpg

 

Sy7lWLH.jpg

 

JiVE7Ji.jpg

 

qptKhcK.jpg

 

Another thing I am taking into consideration is that most, if not all, the weapons used for Rogue One were built from airsoft guns (E-11, A-180, A-280 CFE, DH-17, DL-44, A-300, MWC-35c, SE-14r, E-11D, DT-29, E-22, etc…), so was there an airsoft Lewis used to make the T-21 and if so, which variant of the Lewis was it? The Uk had Mark I through Mark IV versions with 4 different types of the Mark III. There are other version of the gun as well such as the US versions the M1917 and M1918. To complicate matters, there were other versions made for other countries. Soooo, the version of the gun used would shed some lite in some of these noticed changes from the OT T-21s like how the sling attaches and possibly the sights. Additionally, the configuration of the barrel collars is of interest to me. Different versions of the Lewis had different collars at different points along the barrel shroud.

 

Well that is it for the update. I have DragonCon starting tomorrow so it will most likely be next week before I can make an additional progress on this build. Thanks for the interest.

  • Like 1

Share this post


Link to post
Share on other sites

Update,

 

Ok so DragonCon is over and I am back on the T-21 project. I may need to work on my TK as well. The TK kit experienced some damage during the parade but more about that in my TK build thread.

 

Ok so I concentrated on the feed tray. First I cut off the three hex bolt heads and I will be replacing them with round head (rivet looking) greebles I also cut off the lip towards the front of the tray and cut down the tabs on the sides of the magazine cylinder.

 

xYT44uJ.jpg

 

After sanding here is how it looks before I add the greebles. I will be adding a shorter lip where I cut the original one off. I am also looking to add the roll markings on the feed tray but I have not tested how I plan on doing this. I do not have a steady enough hand to scribe them myself. One Idea I have is to make a template and sand blast them on but I do not know if the basting with cut them into the resin deep enough to be seen so I will need to test this. Last resort is to just paint them on. We will see what works out best in the future.

 

GyQLNAG.jpg

 

Next, I primed the barrel shroud parts and assembled them. Since I planned on glueing the 2.5” pipe into the transition, I needed to install the sling mount and tactical light rail during the assembly to be able to access the nuts on the back side of the screws.

 

kuZfovc.jpg

 

I will be building a 1.25” sling so the sling mounts needed to be 1.25” (32mm). I had a spare AK-47 sling mount for this and it fit perfectly. I also had a small rail mount for a bipod that I cut down and drilled holes in to mount it to the side for the tactical light. All this installed and mounted the 3” collar at the transition and glued everything together with E-6000. I clamped it all together and let it sit for 24 hours.

 

aAKC7ov.jpg

 

I also cut a horizontal line on the feed tray to replicate a separation in some parts but I forgot to take pictures of it so I will add it later.

And that is the update. Thanks for the interest.

  • Like 1

Share this post


Link to post
Share on other sites

Update,

 

I wanted to ensure that the barrel was secured to the frame so I notched the frame and cut another piece of plywood.

 

3SPBTBu.jpg

 

Then I fit the parts together and glued them in place.

 

5VlDlf2.jpg

 

I have been torn with rebuilding the cooling fins and adding a cover over them like this.

 

pZqA23x.jpg

 

But this would require another modification to the feed tray and I like how its coming along so this is one detail that will not be incorporated in my build. With that settled, I primed and painted the cooling fins.

 

CMHtExl.jpg

 

I cut the center peep sight out of the rear sight and extended the inside rectangle about ¼” longer towards the bottom. Once I did this, I realized that I will need a longer bolt but I think this looks better.

 

O9CpD3D.jpg

 

So I mentioned in a previous post that I had cut a horizontal line in the feed tray to give it a more realistic look. Here are some pictures of that line.

 

r2Ud9QO.jpg

 

RonhVXc.jpg

 

VCMxoWd.jpg

 

SO I figured out how I will replicate the rivets in the feed tray. I went to Ace hardware and picked up a few things. These are some furniture nails.

 

zOz2Fsa.jpg

 

And this is how they look on the feed tray. Also note that Glued on the low fence just above the rivets in the picture.

 

EGpoFSR.jpg

 

I had some time so I ran a test of the sandblasted roll markings on a spare piece of the resin. Here is the vinyl decal mask I printed in my silhouette. Since these markings are so small, its hard to keep the small vinyl parts that go inside the letters like the letter “b” or “O” but I think the overall look is a nice touch.

 

67VdMun.jpg

 

I applied the mask to the resin and sandblasted it.

 

f0bKhiX.jpg

 

Once I removed the mask, I brushed on some black paint and wiped it away and I like how it turned out. So my plan is to prime the feed tray then mask and sand blast. Then adhere it to the frame and paint it.

 

sTzuFPz.jpg

 

I sanded the sides of the receiver and added some PC-7 to the spring knob to widen it and make it look more realistic. I will sand this once its cured and shape it properly.

 

XK88Y3f.jpg

 

Lastly, another thing I got from Ace Hardware was an “I” bolt and a coupler nut. This will be the tall aerial sight.

 

0kos8mU.jpg

 

First, I needed to make the coupler nut round so I put it on the lathe.

 

1bwuxsP.jpg

 

Next, I ground down the front and back face of the “I” bolt to remove the markings and flatten its rounded look. Then I drilled a hole in the top and through the center of the base of the “I” bolt. Next I tapped the hole with a 4mm tap. Next, I added a 4mm set screw for the sight aperture. In this picture I screwed on the now rounded coupler nut. This is what will protrude on top of the barrel shroud. I think it will work out nicely.

 

LZJP19f.jpg

 

And that is it for the update. Thanks for the interest.

  • Like 3

Share this post


Link to post
Share on other sites

Update,

 

Ok, I attached the barrel shroud with 3 screws that sit under the collar. This picture if the bottom of the barrel shroud.

 

R2JwSrw.jpg

 

Prior to attaching the barrel shroud, I had notched the top plywood support to that the bolt that would hole the aerial sight in place would be accessible. Once the collar was in place, I drilled the hole and mounted the aerial sight on the top of the barrel shroud.

 

HIlzhvl.jpg

 

Here you can see the gap under the aerial sight.

 

qa9XQzu.jpg

 

Next, I cleaned up the front sight. Since I cut off the sight post to drill out a mounting hole, I 3D printed a replacement.

 

QX7icwu.jpg

 

Next, I masked off the feed tray and rear sight in preparation for sandblasting.

 

pMl2gsg.jpg

 

After the sandblasting you can see the roll marks. I do not know how well the will show up after painting but its worth the effort. Also, notice that I had replaced the large black furniture nails with smaller brass furniture nails to replicate the two rivets.

 

W9XDrxu.jpg

 

Next, I mounted the feed tray and chamber. All of this stuff was adhered with E6000 but the feed tray also has 3 screws holding it on.

 

XAQnWDS.jpg

 

Next, I spent a few hours with a sanding drum and got the stock shaped.

 

6BxLD9s.jpg

 

I used some of the left over resin pieces from when I cut down the feed tray to fabricate a mount plate (yellow circle). Also I cut out a flat piece of aluminum that will be glued to cover the trigger assembly (yellow square).

 

dtOp1Ws.jpg

 

Next, I used Minwax Ebony 2718 stain to stain the stock and grip scales.

 

0J8DBbg.jpg

 

wEIOCbL.jpg

 

Next, I fabricated the peep sight for the rear sight assembly.

 

uuOHu8t.jpg

 

I primed, painted, and assembled the rear sight assembly.

 

6X4g3wP.jpg

 

G7UOd3Z.jpg

 

After a thin coat of glazing putty on the sides, I sanded and primed the stock mount plate.

 

Jh9reY5.jpg

 

Next, I cut, shaped and drilled some mounts for the stock screw mounts.

 

8yqa79y.jpg

 

I mounted the front sight with screws and E-6000.

 

sVaAHrH.jpg

 

kFbeOpP.jpg

 

I also mounted the barrel release lever to the bottom of the barrel shroud.

 

kjP63aT.jpg

 

Next, I mounted the side receiver detail resin plates to each side.

 

pzghqUS.jpg

 

srAkpPT.jpg

 

Lastly, I applied a coat of polyurethane satin clear on the stock and grip scales.

 

m4cxfbV.jpg

 

And that is it for the update. Thanks for the interest.

Share this post


Link to post
Share on other sites

Update,

I notched the stock mount plate to allow for the 4 mounting brackets. Next I drilled the screw holes and mounted the brackets.

 

nhL9n18.jpg

 

mlpyxkf.jpg

 

Next, I mixed up some PC-7 and filled in the gap between the chamber and the bottom of the feed tray, the gap between the stock mount and added side detail parts, and the area under the cooling fins and forward of the side detail parts. Once the PC-7 is cured, I will sand and shape before painting.

 

5aOf9EQ.jpg

 

5wNkFd7.jpg

 

Well that’s it for the update, thanks for the interest.

Share this post


Link to post
Share on other sites

The amount of detail on this build has been staggering. I love that you have actually included the factory stamp. Incredible job and I can't wait to see the final product!

  • Like 1

Share this post


Link to post
Share on other sites

DEVOLVER, thank you.

 

Update,

I sanded and somewhat shaped the PC-7 then sprayed everything with a primer.

 

idcLNrU.jpg

 

5aXzauu.jpg

 

I made a butt plate from a discarded black plastic bucket.

 

6kDeoKB.jpg

 

Next I airbrushed the whole thing black.

 

VGwiZJ3.jpg

 

mUdg4v7.jpg

 

ieYG8Dt.jpg

 

I drilled the mounting holes for the oil tube. Then I sanded, primed and painted the oil tube parts from Spool86’s kit. I decided to mount the stock sling mount on the side of the stock since it looks like that is where it is mounted in the screen captures I posted previously. This is also where is was mounted on some later models of the Lewis. It makes more sense for it to be here and not on the bottom of the stock.

 

gF7asjB.jpg

 

This is the barrel cooling fin insert that will go inside the barrel shroud eventually.

 

S6ypjzn.jpg

 

So I still need to weather the whole thing then let it set for a few days then clear coat it. After that, I will wrap the “D” shaped seal around the barrel shroud, attach the tactical light and stock and make the sling. I am hoping to be finished by this weekend. Hopefully, the weathering will bring out the roll marks.

 

That is it for the update, thanks for the interest.

Share this post


Link to post
Share on other sites

Update,

Well I did some dry brush rust on the barrel shroud, collars and front sight. Next I installed the barrel cooling fins and spacer. Next I installed the stock and made the sling. I did some dry brush and wash painting with silver on all the receiver and feed tray parts. The roll marks are visible but they are not as prominent as I would have liked. I glued on the grip scales with E-6000 and they are still curing when I took these pics. If anyone else is looking to do the mask and sand blast method, you may want to paint the feed tray and rear sight first then sand blast and then touch up the paint and they should stand out more. Anyway here are some pictures of how she looks so far.

 

6ft02e9.jpg

 

WJyEsRU.jpg

 

XwBRBvV.jpg

 

kavacy0.jpg

 

bE6MUn5.jpg

 

j5toI3B.jpg

 

UnJoNLp.jpg

 

2h66H4H.jpg

 

fX21cjB.jpg

 

zAn5XO0.jpg

 

So I will do a black wash tonight and then let it sit for a few days then apply the clear coat everything. After the clear has cured, I will add the “D” gasket and she will be done. One thing I did notice was that the cocking lever in Spool86’s kit is on the right side of the receiver and I have seen several videos of it on the left side. Either it is ambidextrous and can be switched or some models of the Lewis have it on both sides. I am not sure which it is, but it is just a small detail that I am not too worried about. Additionally, in all the pictures of the Lewis I have seen, there are no visible grip screws that hold the scales on the receiver; however, in the two videos I have seen of CGI Lewis guns disassembly, they show screws for the scales? I just glued mine on but it got me thinking, how are the actual grip scales attached? Anyway, just another detail that is not a big deal.

 

So that is the update, thanks for the interest.

  • Like 2

Share this post


Link to post
Share on other sites

Update, So I did the black wash last night.

Here is a picture of the wash still wet.

 

1Ci2V9P.jpg?1

 

Once the wash was dry, I took these pictures. Notice how the wash has toned down the silver.

 

T5f7gi6.jpg

 

0BRuZE9.jpg

 

Zn2FUcU.jpg

 

njRjbWe.jpg

 

I will wait for 24- 48 hours then clear coat everything. After the clear is dry, I will wrap the “D” gasket and that will complete the project.

 

Thanks for the interest.

  • Like 1

Share this post


Link to post
Share on other sites

Update,

I applied the clear coat and hung the rifle to dry.

 

rUEQHXr.jpg

 

Next, I wrapped the “D” gasket and put the sling and tac light back on. I do not like how the “D” gasket looks so I will be looking for a different solution. But my Rogue One T-21 is done for now. If I change out the “D” gasket, I will post an update; otherwise, the gun is done.

 

763NMM2.jpg

 

7JEHExz.jpg

 

NVmfbgF.jpg

 

5iYk8Ju.jpg

 

lN6CR4h.jpg

 

Thanks for the interest.

  • Like 1

Share this post


Link to post
Share on other sites

Time to wire that bad boy up with some electronics lol

  • Like 1

Share this post


Link to post
Share on other sites

That's a beautiful end product. The amount of detail you have put into this definitely shows.

  • Like 1

Share this post


Link to post
Share on other sites

“Time to wire that bad boy up with some electronics lol”…

Ukswrath, there may be a time for that in the future but that time is not now. I made the trigger functional in case I decided to do just that in the future. Since most of the parts were glued in place with E-6000, deconstruction to add electronics will be somewhat difficult.

 

DEVOLVER, thank you for the compliment.

 

Update,

Well, like I said previously, I did not like who the “D” seal looked so I found a better option. I purchased about 25’ of 7/64” Windshield washer vac tube. This hose is a stiffer and thicker walled rubber tube.

 

QTailvo.jpg

 

So I removed the “D” seal. Next I drilled a small hole for the washer tube to be inserted into the barrel shroud on the bottom near the collar closest to the feed tray. I spread some E-6000 all over the barrel shroud where the washer tube will be wrapped. I locked the starting end of the washer tube in the hole and started wrapping the tube. Keeping constant tension on the washer tube as I wrapped it around the barrel shroud till I hit the end point. I drilled another hole and locked the end of the tube inside the hole. Presto, a better looking T-21.

 

xmXerNn.jpg

 

Bf25AGz.jpg

 

Well that finishes the Rogue One T-21. Thanks for the interest.

  • Like 2

Share this post


Link to post
Share on other sites

Very nice. FWIW my T-21 utilizes plastic air line for the tubing. 

IMG_3150.jpg

  • Like 1

Share this post


Link to post
Share on other sites

Great work, some nice detailing, well done. 

 

 

 

 

 

  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×