Skorpion1974 Posted July 7, 2016 Report Share Posted July 7, 2016 (edited) Armour = RS Prop Masters Helmet = RS Prop Masters Blaster = RS Prop Masters Height = 5'11" Weight = 90kg Boots = RS Prop Masters Canvas Belt = RS Prop Masters/Clothears Hand Plates = RS Prop Masters (Latex) Electronics = RomFX Neck Seal = RS Prop Masters Holster = RS Prop Masters Edited September 20, 2016 by Skorpion1974 Quote Link to comment Share on other sites More sharing options...
Skorpion1974 Posted July 7, 2016 Author Report Share Posted July 7, 2016 Forgot to mention the is ANH Stunt Quote Link to comment Share on other sites More sharing options...
illusionz_09[TK] Posted July 7, 2016 Report Share Posted July 7, 2016 Dave, you are missing a couple pictures: a picture of the back of the TD to show the screws/clips an action shot pic close up pic of the ab buttons details cod/butt snap/rivet connection Extra enhances to the armor: the cod rivet should not be painted white you may also want to tighten up the shoulder bells closer to your traps also, the shims on your ab/kidney connection should be seamless Good luck bud, U.K. and Sly should be with you soon enough; it looks like they are backed up a bit with the holidays. Quote Link to comment Share on other sites More sharing options...
Skorpion1974 Posted July 7, 2016 Author Report Share Posted July 7, 2016 (edited) Just a couple from the library I have already, will have to suit up and get some more shots for the remaining adjustments Edited July 7, 2016 by Skorpion1974 Quote Link to comment Share on other sites More sharing options...
Skorpion1974 Posted July 7, 2016 Author Report Share Posted July 7, 2016 Pics all done, hopefully I have got them all this time Quote Link to comment Share on other sites More sharing options...
illusionz_09[TK] Posted July 7, 2016 Report Share Posted July 7, 2016 Dave, the butt plate snaps should not be painted white. When you get a chance you should definitely remove the paint. Quote Link to comment Share on other sites More sharing options...
Skorpion1974 Posted July 7, 2016 Author Report Share Posted July 7, 2016 Butt Rivets done Quote Link to comment Share on other sites More sharing options...
Skorpion1974 Posted July 21, 2016 Author Report Share Posted July 21, 2016 Anything else needed for this application? Quote Link to comment Share on other sites More sharing options...
illusionz_09[TK] Posted July 21, 2016 Report Share Posted July 21, 2016 Sly & Ukswrath are a bit backlogged; i'm sure they will be on to review your updated submission soon. 1 Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted July 21, 2016 Report Share Posted July 21, 2016 Hey Dave myself or Sly will be with your shortly 1 Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted July 25, 2016 Report Share Posted July 25, 2016 Hey Dave welcome. Thank you for your EI application. Lets get started. CRL and EIB Application Requirements: All submission photos have been posted. Your armor displays all the necessary elements to qualify for Expert Infantry. Welcome trooper! Other-Armor Fit/Assembly: In this section we review observations made by your fellow troopers and ourselves. Some observations may lead to suggestions to improve the overall look of your armor. If any suggestion affects any application, it will be listed separately in the above or below sections. If we had any suggestions it would be to reduce your shoulder bell to chest and back plate gap. It appears you fill out your armor quite well and have made the necessary adjustments to bring them closer. Reference photo Centurion Suggestions: Because Centurion photos show much more detail than EIB, items pertaining to Centurion might be seen there and not here. We try to point out all we can from what is seen but the final accuracy is the responsibility of the trooper. This is also where we try and get you in the best possible position for a successful Centurion application. 1) Though not bad, the drop box alignment could use a bit of fine tuning. For level three certification (if applicable): Drop boxes must have full inner drop boxes to close the back. Flat covers are not allowed. Drop boxes are vertically aligned with the end of the ammo belt with minimal gap between belt and box. If you were to glue the drop box straps to the cloth waist belt it may help prevent them from shifting. Reference photo. I like to to use this photo of Han because it illustrates that even when bent over the drop box still remains aligned with the ammo belt edge, 2) Kidney shims. The CRL states there can only be one seal between the kidney and ab. Using some ABS paste and paint this can be easily updated to look like one seam. For level three certification (if applicable): A single visible seam line is present. Reference picture That's it brother, great job. After a couple updates hope to see you at Centurion Quote Link to comment Share on other sites More sharing options...
WhiteRoseSwampy[TK] Posted July 25, 2016 Report Share Posted July 25, 2016 Congratulations trooper! Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Skorpion1974 Posted July 25, 2016 Author Report Share Posted July 25, 2016 Awesome, thanks for the advice and look into getting done whats needed for Centurion Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.