Arnie_DK[TK] Posted May 22, 2012 Author Report Share Posted May 22, 2012 (edited) Just picked up a box from Paul today. Here is the insede content Two great looking helmets. I'm partly exited and terrified, at the same time, but I think its going to be a fun build to try! No sniper plate at this time though, but I'll manage afterall its my own fault the old one is warped Edited May 22, 2012 by Arnie_DK Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted May 22, 2012 Report Share Posted May 22, 2012 That was quick! Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 22, 2012 Author Report Share Posted May 22, 2012 Oh yes indeed Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 23, 2012 Author Report Share Posted May 23, 2012 Startet a bit of trimming today, and when I have the face in the position I want the tubes sit very wonky. Can this be helped, if I trim some more on the forehead, that goes under the helmet? I'm comparing it with the helmet TM assembled and painted. Quote Link to comment Share on other sites More sharing options...
troopermaster Posted May 23, 2012 Report Share Posted May 23, 2012 You can have the tubes line up or have them wonky. It all depends on the look you are going for. Each helmet is assembled slightly differently than the other so go with what you like. Take the ear caps off the one I assembled to see if the tubes line up or not if it helps. Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 23, 2012 Author Report Share Posted May 23, 2012 This setup speaks to be in quite a soothing way I like the low brow and the way the tubes line up. Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 26, 2012 Author Report Share Posted May 26, 2012 Test fitted with the srews from my "old" helmet. Looks allright I think. The brow is slightly higher on the right side, but nothing anyone will notice unless they look for it. Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 26, 2012 Author Report Share Posted May 26, 2012 I bought the paints recomended for painting the bucket. Humbrol no. 5(grey) 14(blue) and 21(black). They are all gloss, but the one TM painted is in matt colours. What would be the most correct? I used the same colours on my ab buttons, and I like the shine, but dont know about the helmet. Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted May 26, 2012 Report Share Posted May 26, 2012 I know TM sometimes uses Mediterranean blue for the tube stripes. The vocoder looks to be satin black (#85). Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 26, 2012 Author Report Share Posted May 26, 2012 The vocoder looks to be satin black (#85). Hehe freak accident, but thats actually what I just bought today. I thought I bought the #21, but #85 must have been in the wrong place Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 26, 2012 Author Report Share Posted May 26, 2012 Cut out the eyes and teeth. Noticed one of the teeth need a bit of sanding, but otherwise happy with it. Think I'm ready to rivet it now. Wil have to find some screws and bolts for the ears as well. The ones used here belong to my completed helmet Quote Link to comment Share on other sites More sharing options...
troopermaster Posted May 26, 2012 Report Share Posted May 26, 2012 Didn't I send you the bolts for the ears? I can send you the correct brass bolts on Monday if not. Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted May 26, 2012 Report Share Posted May 26, 2012 Looks good. I agree on the teeth. Just a tad more, maybe a little more "square". Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 26, 2012 Author Report Share Posted May 26, 2012 Didn't I send you the bolts for the ears? I can send you the correct brass bolts on Monday if not. Nope, just the rivets and washers, but thats allright, I will take a look in the hardware store and see what I can find Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 26, 2012 Author Report Share Posted May 26, 2012 I hate the ears... First ear done, except for some light sanding. This is as good as it gets for me... Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 27, 2012 Author Report Share Posted May 27, 2012 Both ears are on, but they are not as flush as I had wished for, but I dont think it will be any better. I found some screws and washer in the hardware store. They are slightly bigger, but it was the closest thing they had. And was probably cheaper (5£ ish), than having Paul mail them to me from the UK Next step, painting. Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 27, 2012 Author Report Share Posted May 27, 2012 All black areas are drying now. Quote Link to comment Share on other sites More sharing options...
Rich330[TK] Posted May 27, 2012 Report Share Posted May 27, 2012 Ears look just right to me. Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 28, 2012 Author Report Share Posted May 28, 2012 Painting progress. next up is black stripes. Quote Link to comment Share on other sites More sharing options...
troopermaster Posted May 28, 2012 Report Share Posted May 28, 2012 Looking good Morten. Now your ready for the fun part - the tube stripes Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted May 29, 2012 Author Report Share Posted May 29, 2012 Yaaaaaaaaayyy..... Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted August 11, 2012 Author Report Share Posted August 11, 2012 This have been lying dead in the water for a while now. Just been too busy to finish it, but its finally done, and I have already been wearing it for some unofficial trooping. But final pics of the helmet kit. My other TM helmet kit, will be used in a replica HDPE build, but that will probably get a thread of its own when I get the time to start it Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted August 12, 2012 Report Share Posted August 12, 2012 Tube stripes are a bit too low on the sides. Should be closer to the face. But I approve of the rest of the assembly. Quote Link to comment Share on other sites More sharing options...
Arnie_DK[TK] Posted August 12, 2012 Author Report Share Posted August 12, 2012 Garh Well, that will have to be fixed some other time Quote Link to comment Share on other sites More sharing options...
Locitus[Admin] Posted August 12, 2012 Report Share Posted August 12, 2012 It's good to have things to do. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.