First0rder

Anytime

Hey Anzo,, i got the Montana Cans ordered and shipped to my house from Blick Art Supply here: https://www.dickblick.com/ . here is a direct link to the product. hope this helps: https://www.dickblick.com/products/montana-gold-acrylic-professional-spray-paints/

I just had a Future Trooper ask me a few questions about my Executioner so thought I would Post them on my build for future troopers as well. Some great questions asked. Hope these help but if not, pls ask for further clarification. - Can you list all of the spray paint you used I used Montana Cans Gold Series Universal Primer and Shock White and Black. Reason why i went Montana Cans is that its an Acrylic based paint that offers more flexibility than Enamels or Lacquers. I used Montana cans for all 3; Primer, Top coat and Clear coat. Clear was Gloss on white and flat on the black. Additioanlly i also used Primer from Rustoleum for Etching Primer and Rustoleum High build primer. - Can you List the steps you took to paint everything? Especially the helmet The paint was a lenghtly process, only cause i really like my paint to look like glass. But if you are not, you can certaintly skip some of the processes performed. Start - mix up bondo and run a skim coat over the helmet, this will start filling in all the low spots. Next lay a thin coat of filler primer and allow to dry. Block Sand the helmet with 240 grit carfully. Rinse with water and hold into the light reflecting the surface looking for high / low spots. if you see more low spots, mix up more bondo and repeat steps. Once level, spray ecthing primer and allow to dry. Wet sand with 400 and rinse and allow to dry. Spray 2 coats of Montana Cans Universal Primer. Once dry, using Bondo Spot filler, fill in any pin holes. Wet sand with 800 grit. repeat for any missed pin holes. Now your ready for Base Paint. Lay down 2 coats of White and allow to dry. Wet Sand with 1200. Lay down another 2 coats of White and allow to dry. Wet sand with 1500. Now your ready for Clear. Lay down 2 coats of clear and allow to dry., Wet sand with 1800. Lay down another 2 coats and allow to dry., wet sand with 2000. Now Very Important - Allow the Helmet to dry for 5 days before touching again. Since there is alot of paint and clear, it will take time to fully cure and harden. If you Dont wait and start masking off for the black, youll find that the paint is still soft and youll have tape marks left behind and will need to wetsand again. For the remaining parts - i repeated all above but skipped the 2nd bondo application. - Did you have to get any extra pieces to make the kit accurate? All the hard goods from Jim were acurate enough for lvl 1 approval. However when you want to achieve lvl 2 or higher approval, then youll need to outsoure a better belt, rubber gaskets. Youll want to reference the CRL closely: https://databank.501st.com/databank/Costuming:TK_TLJ_Executioner - Any areas you feel needed to be reinforced and how did you do it? Youll find that you need to Reinforce a few areas immediatly. Mainly the Yoke and Thighs. There are a bunch of build threads where the gents used Fiberglass Boat Repair to Reinforce the inside of the parts and others had used Devcon Plastic Welder. I would do either or. - Anything you wished you did now that your done? For the Yoke, I would recommend getting Ukswraths @ukswrath yoke supports. Really wish i used them as film acurate and fantastic option to reinforce the yoke. Wish i had also contoured hte back side of the thighs to allow more mobility and also countoured the upper thighs more to match the cod. - what glue did you use? Devcon Plastic Welder, Loctite CA Universal, Loctite Marine Grade Epoxy - How did you get the lens in? Epoxed Chicago screw bases to the inside of the helmet . then marked and drilled a small hole for each and secured with screws. - magnets or snaps? Both. Magnets on the Chest plate and snaps everywhere else. - Can you list all of the sand paper you had to use? 240 Dry, 400W, 800W, 1200W, 1500W, and 2000W - Can you list the extra pieces you had to buy on top of the kit? Undersuite from Stormtrooper Undersuit, Gloves and Boots from Imperial Boots, Belt from Belts of the FirstOrder @JAFO, Neck seal from Anovos Premeir Line, Cloth Gaskets from Jim, Canvas Belt boxes from TrooperBay, Helmet Sound and Fans from Ukswrath @ukswrath.

Your correct on the Black, I did Traps in Gloss. As to the lens, i did this: Epoxied the Chicago screws base to the inner of the helmet and allowed to dry. then i layed the lens over and used a black sharpie marker to jot where to drill the holes. finally used the screw to secure.

Epoxied the Chicago screws base to the inner of the helmet and allowed to dry. then i layed the lens over and used a black sharpie marker to jot where to drill the holes. finally used the screw to secure.

Kits coming out awesome!

Great Advise Gents!

TK-19736 Requesting TK 501st WhiteArmor Approval https://www.501st.com/members/displaymember.php?userID=25049&costumeID=406 https://www.501st.com/members/displaymemberdetails.php?userID=25049 Thanks

Havnt done anything with KB myself. See a few troopers doing Mimic.

Hi All, Was too excited and forgot to post in here. TK Appoved on Dec 8th, 2017 as a FOTK from TLJ. Thanks all!

Congratulations Taylor!!! Well done indeed!

Merry Christmas to you too! yeah and get cracking on that again.

Its painful waiting on gear to arrive, ive actually built an OT TK while waiting on Anovos to deliver. haha As for ESPN sadly that wasnt me with Kevin. That was Chris A from NEG and the other 2 Troopers were from the Midwest Chicago garrison. So what do you have in hand now and what are you waiting on again?

Are you doing 2 kits? seeing the Anovos and Jims helmets. also 2 sets of spats.

Thanks Glen and thanks for the stats Lol, IDK, what are we thinking?? haha

Thanks Matt!!!! Oh, how to tell?? is there a Trooper DB that we can see the current count of each approved?

Hahah, thats ok Mark. Where all here to help no matter what you are building ;0 But yes in this case the BlizzardForce would know all that there is to be known.

It would be AWESOME! and we would all sing in unison "Everything is Awesome, Everything is cool when your part of a team" ahhaha!

Great news Everyone! Ive been cleared!!!!! Now can troop as a FOJE! https://www.501st.com/members/displaymemberdetails.php?userID=25049 BTW, did i make the first of 10?

nah, other than overspray from painting the exterior i didnt do anything, just the plasticdip, 2 coats if needed to suppress the fiberglass.

Seriously need patience for this build wowo!!!

Thanks Darren, i will Hi, Mainly PlasticDip the inside of all the parts, But also around the inside of the ankles and spats i added Felt. To both add cushion and protection to the boots. For the Yoke and Chest Plate, i added Small D ring Rubber weatherstripping to also protect the parts form scathing against one another. Hope that helps.

Boy I do have to give it to you for your patience with not only cutting and gluing the ABS parts but having to seam and still go through the fitting and painting process. Overall how has your experience been thus far with this kit? Would you do it again?

All ive heard thus far is that since its a new costume and they havnt seen before they were going through the legion to make sure they get it right. So i guess i quietly wait for now Thanks Paul, Darren, and Deo for your support

Alls quiet and still havnt heard from my Garrison on this submission. only thought is that someone in Legion is still reviewing? Any of you leaders here seen it as a request by chance? Andy