[Ukswrath's AM 1.0 build]

I'm just going for basic. The indented one would be fine, right?

What about the square covers. Which ones?

[ANOVOS TK Vs. Craigslist Shadow TK (HELP)]

I agree above; the plastics could vary. Buy the new kit.

Make you son pay the Craig's List price and you kick in the up charge for the Anovos.

[Inkedfritos686 ANH AM 2.0 build and journey]

I had a similar problem and had to trim the notch at the top as well as some of the back top area.

 

What do you have to lose at this point!

[Ukswrath's AM 1.0 build]

I have the AM 2.0 kit and received 2 different belts and square buttons.  

 

I noticed that in Section 11 you were using the one with the square depressions and the bigger diameter buttons.  http://www.whitearmor.net/forum/topic/31920-ukswraths-am-10-ata-bucket-build/page-3

 

I'm going for ANH Stunt TK and HWT.

Which belt and buttons are correct, and what's the other one for?

 

 

[Has Anyone Purchased/Assembled This Kit?]

Good to know since I already painted it a bit. Thanks a lot. This makes me feel better about making this into something troop-able.

[Has Anyone Purchased/Assembled This Kit?]

Pretty expensive stuff. Glad to know if worked for you

Do you apply if before or after painting?

[Swag Toss]

Mon Motha

[HWT Pack Build - SheaJeff]

And which button covers are correct?

 

[HWT Pack Build - SheaJeff]

Just a quick question.

My AM 2.0 kit came with 2 belts as shown.

Which one is correct for HWT and ANH TK?

 

[Has Anyone Purchased/Assembled This Kit?]

Its fragile until you put resin on it.

 

 

Sent from my iPhone using Tapatalk

What exactly should I put on it?

[Has Anyone Purchased/Assembled This Kit?]

I have this kit. It's a ton of sanding and even then isn't the greatest and is really fragile. It's so time consuming I haven't even finished it. Can't imagine tripping with it.

Save your money and buy a hyperfirm if you're looking for something to troop with.

[Inkedfritos686 ANH AM 2.0 build and journey]

I had the same gap above the ear. It should be covered if you trim the ear right.

I had the trim the top section of the ear as well as the bottom curve. You can see the difference in "thickness" of the top section, particularly compared to the other side.

 

 

 

[Another HWT Backpack From Spain]

I wanted an antenna like that too bad t was worried about trooping indoors.

[Inkedfritos686 ANH AM 2.0 build and journey]

I started with the brow low like that too, but be warned: when you pull the cheeks in with the additional screws the brow lowers a bit. I'd go higher on it.

[HWT Pack Build - SheaJeff]

I want to buy my wife a new sewing machine so that she can sew the industrial strength velcro to elastic, but I know I'LL end up doing the sewing!

[Securing items inside the helmet - how?]

It appears my AM 2.0 trim is a lot thicker than yours.

My problem is that if I put it on like yours, I get these "lumpy" areas AND my big long head has more trouble squeezing in (I've already trimmed the opening as much as I dare).

If I put it the other way (picture 2), then it looks cleaning and gives me a bit more clearance in the opening.

Does it really matter which way it goes?

Perhaps I should buy a different trim piece that's "thinner". (Trooper bay maybe?)

 

 

[Securing items inside the helmet - how?]

Hey, could somebody me please post a picture of the correct placement of the S rubber around the bottom rim of the helmet. Which part goes onto the helmet (wide or narrow)?

 

Also, where does it stop/start? Front, back, doesn't matter?

[Securing items inside the helmet - how?]

I found the sticky back Velcro does come loose, (it gets pretty hot here) so I use E6000 on normal velcro

Arg!

I just read this after I spent time putting Velcro in the helmet Just using its regular adhesive backing.

Oh well, when it starts to come loose I'll re-do it with E-6000.

[Securing items inside the helmet - how?]

Wow! Good to know. Sounds like there is a lot more to the power supplies than I realized. Thanks.

[Securing items inside the helmet - how?]

What they say...

 

Velcro

 

Your helmet looks amazing inside.

Do you have a build thread on it?

[Securing items inside the helmet - how?]

It normally runs off a 9V but you can replace it with the larger power pack if desired.

My plan in the future is to switch everything to use 1 USB source.

[Securing items inside the helmet - how?]

I just got my ROM/FX and the optional AA battery pack but it holds 8! AA batteries. I'm. It sure Velcro will hold that kind of weight so I may have to move that to the chest.

[Securing items inside the helmet - how?]

Thanks guys. Velcro makes it easier and saves me $18 on gaffers tape. I appreciate the help.

[Securing items inside the helmet - how?]

I'm at the point where I am beginning to mount items inside the helmet, and am not sure of the best method.

I've mounted the welding shield using the ear screws, and the head padding with Velcro strips.

 

What's the best way to hold the screen and the electronics inside the helmet?

(fans, ROM/FX and mic, Ukswrath's hearing assist)

 

I've seen mention of gaffers tape, but read on Amazon that it's meant to be temporary. 

Is Velcro a better option?

Is there something else I should be using?

 

Thanks for the help.

[EVA foam TD armor for my daughter.]