DeceptiSean

Now I will work on the thighs. Thighs were very difficult last time and I'm hoping I will be as lucky fitting these. Sent from my iPhone using Tapatalk

Work has stalled. But I have jumped back in and trimmed shins and glued them together Sent from my iPhone using Tapatalk

I've noticed that by just following mould lines I'm left with a lot of return edge on some of these parts. The collar area will have to be trimmed. And the ab plate My MTK(centurion approved) has 10mm of return edge in these areas So I will do the same here. Also, going to clean up some other areas to get them a bit more uniform. Sent from my iPhone using Tapatalk

I try to glue the cover strips on up against the edge of this ridge. Sent from my iPhone using Tapatalk

Cover strips, I'm doing the same measurements here as I did with the forearms(15mm). I suggest that you plan out how you will cut out cover strips as to utilize as much of your abs sheet as possible. Otherwise, you may end up with a sheet like this... Sent from my iPhone using Tapatalk

Progress on the forearms Now that these are glued I will move on to sanding. Sent from my iPhone using Tapatalk

When I left off I was putting a forearm together, it's getting there. One more bit of glue and it will be ready for extensive sanding at the elbow end return edge. While I was waiting on the glue I started trimming the bicep. Then I had a bit of a stabbing incident. Note, cut prof gloves DO NOT protect against stabs. I don't get a lot time in between work and children so I tend to rush things or forget to update the build thread. That's why we will now take a leap to all arm parts having been trimmed. Going to leave it there for tonight. I will need to do a lot of sanding and I'm waiting for CA glue, magnets and more clamps. Sent from my iPhone using Tapatalk

You're lucky it's only 9 months. My kit was an 11 month wait and I got it at 16. Sent from my iPhone using Tapatalk

Got some time tonight to continue working on this kit. So far, I've glued the halves of a forearm together on one side. While the E6000 dries I'll continue trimming the other bits. Sent from my iPhone using Tapatalk

how long is your wait time? Mine was 11 months but went a little longer. Sent from my iPhone using Tapatalk

As far as children would let me get tonight. Sent from my iPhone using Tapatalk

Welcome to my second build thread. This time around I will be putting an ATA together. I'm following the instructions UKSWRATH put up for his Anovos build and using whatever I can remember from my MTK build. I was able to achieve level 3 Centurion approval with the MTK so I will build for that with my ATA. I was able to pick up a helmet when I asked to get on the 11 month waitlist so I've already put that together. Here's the Big Brown Box Started the trimming the armor at the forearms. I've cut them down to where I want them. I'm putting 15mm cover strips on the arms so I've cut down to about 7.5mm on Botha's sides. Done for now. The next step will probably be to trim all the other pieces. Sent from my iPhone using Tapatalk

Sean Mynster TK 21115 Letter Andrew Sent from my SM-G920V using Tapatalk http://www.whitearmor.net/eib/certificates/21115-eib.png

Sean Mynster TK 21115 Letter Tony Sent from my SM-G920V using Tapatalk http://www.whitearmor.net/eib/certificates/21115-centurion.png

Did you replace the screws or nuts that came with the brackets? Mine seem shorter than yours. Sent from my SM-G920V using Tapatalk

Thank you sir! So stoked I made it. Sent from my SM-G920V using Tapatalk

Thank you! I am ecstatic and very grateful to the forum and your build threads specifically. Without that information, I would have had a much harder time putting my armor together. Does the detachment still provide Centurion certificates? Sent from my SM-G920V using Tapatalk

Ok, no problem. Sent from my SM-G920V using Tapatalk

D-ring Action shot Sent from my SM-G920V using Tapatalk

Thank you! I am a bit confused about the action and d-ring shot. It was my understanding that a picture of the d-ring is not necessary for Centurion because it was required for EIB and since you have to be approved for EIB before you submit for Centurion it is then assumed you still have the d-ring. I have both d-ring and action pictures and can submit them but didn't because they are not on the photo checklist. As for my mic tips, I don't think it would be an issue. Somebody was recently approved with the same armor and mic tips. I appreciate your critique though. Sent from my SM-G920V using Tapatalk

Name: Sean Mynster TK ID: 21115 FISD forum name: Deceptisean Garrison: Imperial Sands Garrison EIB thread http://www.whitearmor.net/forum/index.php?/topic/38621-TK-21115-Requesting-ANH-Stunt-EIB-status-(MTK)-[633] Armor Maker= MTK Helmet Maker= MTK Blaster type= Hyperfirm E 11 Height=5'8" Weight=168lbs Boots Maker=TKBOOTS Canvas belt=Myself Hand Plates Type=Trooperbay rubber Electronics=Fans Neck Seal Type=Trooperbay Holster type=Trooperbay Full Body Front-Arms at side Back-Arms at sides Left-Arms raised Right-Arms raised Armor Details Ab/Kidney Attachment-Button Orientation Butt/Kidney- Fixed= No Hand Plates Shoulder Bridge Back Shoulder Bridge Front Back/Chest connection Thigh Pack Attachment Knee Plate Drop Box Back Cod and Butt Plate Attachment Interior Strapping Kidney Plate Notch Wrist side of forearms Helmet Details Front Side-Left Side-Right Back Hovi Mic Detail Lens Color S-Trim Blaster Details Blaster-Right Blaster-Left Accessory Details Neck Seal Thermal Detonator-Back Holster Attachment Thank you for your consideration. I hope the pictures supplied will suffice. Sent from my SM-G920V using Tapatalk

I will try to submit in the next day or two. Sent from my SM-G920V using Tapatalk

Thank you very sir! I will be posting my centurion submission very soon. Sent from my SM-G920V using Tapatalk

Sent from my SM-G920V using Tapatalk

Thank you, hopefully Tony and Sly think so too. Sent from my SM-G920V using Tapatalk