Jump to content

Rapstertee (TK2135) ANH Stunt build 2014 (pic heavy)


Recommended Posts

Hello!

I'm almost there with my Stunt build now, so I wanted to put up some of my progress pics for inspection.

Apologies for the graininess of some of the pics but it was my antique mobile phone - rest assured my clearance and final pics will be crisp.

 

I'm building with Centurion status in mind, so admins please can you check and advise as and where neccessary? :)

 

First off, Ab plate, right hand side:

160320141115_zps9b192bae.jpg

 

Ab plate, Left hand side (rivets will be painted white)

160320141114_zps006ed702.jpg

 

Cod piece rivet (does this need to be white also?)

160320141113_zps610847b2.jpg

 

Closeups of the rivet inside:

160320141107_zps62e1b0d7.jpg

 

Shoulder bridges:

100320141092_zpsc6df7971.jpg

 

Inside right of ab plate

100320141085_zps377e52f1.jpg

 

Inside of chest/shoulder bells assembly:

100320141084_zpsa676a246.jpg

 

Back/Kidney/buttplate assembly:

100320141083_zps604d2f05.jpg

 

Hand-painted Ear bumps ®:

090220141009_zpsc842fa96.jpg

 

Ear bumps (L)

090220141008_zps1dfddd01.jpg

 

Thermal Detonator:

090220141004_zps0dbf7cda.jpg

 

090220141003_zpsbfa1e59a.jpg

 

Dropbox R:

090220141001_zpsee0e678a.jpg

 

Holster attachment on Left:

090220141000_zpsdf6582ce.jpg

 

Holster from outside:

090220141000_zpsdf6582ce.jpg

 

Belt (rivet covers now attached)

09022014998_zpsf6538c5e.jpg

 

Green lenses and hand painted detail (except tube stripes)

DSC03383_zpsa3ba4399.jpg

 

S-Trim:

DSC03382_zpsebc77c2a.jpg

 

Hand painted tears:

DSC03381_zpsb6b068c1.jpg

 

Hand painted frown:

DSC03380_zps0f79bd88.jpg

 

Hand painted Vocoder

DSC03379_zps4c0d2e35.jpg

 

Hand painted traps

DSC03378_zpse1777f0a.jpg

 

Curved Ammo Strap

DSC03331.jpg

 

That's it for now. I will post up further pics very soon! :)

 

 

 

 

Link to comment
Share on other sites

  • 2 months later...

Okay, all the kit on, here are some pics for pre-clearance inspection - I will note the things I need to change, so you don't need to worry about them...

NB: These are NOT my clearance pics. I will do my final fixes then take some outdoors with a plain BG.

Lids off:
20140603_144129_zpsad2df0c4.jpg
Not looking too bad. Authentic 1976 hair and sideburns - check!

RIGHT side:
20140603_144106_zpscc49ed0c.jpg
1/2" side gap, hope this will decrease as my girth/weight does. TD needs lower placement (re-bend clips). White Knee rivet.

REAR full:
20140603_144057_zps538c70c9.jpg
Lower the TD, close calves more straight. (right one has a 'twist' in it)

LEFT side:
20140603_144048_zpsfaadecdd.jpg
1" side gap. Paint rivets white. lower TD.

FRONT full:
20140603_144036_zpsea4d128b.jpg
Might take another inch or half-inch off the top of thighs. Need to pull ab& cod up by shortening inner elastics.

REAR lower:
20140603_143936_zps1ed2cc30.jpg
Close calves properly. Shorten crotch elastic by 1". Calves need padding inside - they're digging into my knee bones!

REAR upper:
20140603_143900_zpsbb7a0299.jpg
neckseal needs tucking in. TD lower. I know the shoulder bridges look uneven - that's just the placement of elastic pulling the right one down lower.

LEFT closeup:
20140603_143851_zpsde47fa76.jpg
Paint rivets white. (does the holster need white rivets?) Lower TD. 1" side gap

RIGHT closeup:
20140603_143843_zps55d3e051.jpg
Rivets on knee need to be white. Cosmetic popper on ab corner is only slightly visible.

FRONT closeup:
20140603_143816_zps6db0ea8b.jpg
Turn (painful) left shin outwards a bit.

Thigh before trimming:
20140601_225309_zps996f09ee.jpg
Just showing how much I've taken off the top edge of both thighs to allow my knees to bend.

Link to comment
Share on other sites

Untitled_zpsd7977dad.png

I really would rather have seen you cut that thigh top on this outline:

 

I would hit your side rivets white, your power pack rivets on the right thigh white. Leave the cod rivet and male snap on the upper right of the ab unpainted.

In regards to fit, your thighs look really big especially at the knee. The human thigh is conical. Larger at the top and smaller at the knee. Your thigh armor should match that.  I would separate the rear seam (hopefully you used E6000) and get someone to help you. Once separated, squeeze the halves together. You will have overlap at the bottom. release the squeeze until comfortable. Mark a common line in the center to trim by. you will see how much better it looks and feels. You will need to reduce that side gap to no more than 1/2 inch. you have some nice looking armor, Sir!

Also, your thermal detonator clips should be attached with slotted head screws rather than pop rivets. This will benefit you because the clips need to be farther outward towards the side caps with minimal to no gap between the clip and the end cap

Link to comment
Share on other sites

  • 2 weeks later...

Okay chaps - My clearance photos! Thanks for the South Wales Troopers and surrounding supporters for all their help.

01f_zpse13e73c7.jpg
FRONT

012b_zps88179071.jpg
REAR

02L_zpse474c0ac.jpg
LEFT SIDE

010lcu_zps1785cd5e.jpg
LEFT SIDE CU

05r_zps820ffe28.jpg
RIGHT SIDE

011rcu_zps8f8d4055.jpg
RIGHT SIDE CU

08lo_zps81193233.jpg
LIDS OFF

06a_zps380890c2.jpg
ACTION shot A

07a_zps429fcd01.jpg
ACTION shot B

 

I'm going for Centurion Status as soon as my TK# is renewed in the UKG. Any feedback is welcome.
 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...