Casperiser

Thanks all! I’ve given my belt a haircut and trimmed the back of my thighs which now look and feel much better. Thank you all - hope to see you on future troops!

Jamie Kingston TK 14627 Centurion A4 Joseph http://www.whitearmor.net/eib/certificates/14627-centurion.png

Oh wow! Thanks everyone, I’m absolutely thrilled! completely humbled by the support, advice and guidance along the way. this is an amazing community to be part of. thank you!!

Hi Joseph, i apologise this was my fault.. Here is a pic of the area as was originally in the pics, no revits however a black mark where the repair was. I have now cleaned it up so it looks much better, unfortunately there are 2 cracks there which are patched on the underside. Hopefully this looks much better now? Jamie

Hi Joseph, that is where I have a crack which I repaired with super glue / t shirt. Some of the glue seeped through and got a bit discoloured. I’ll clean it up And post some more pics shortly. There are no rivets there. Jamie

thanks all!

Jamie Kingston 14627 EIB A4 Size Joseph http://www.whitearmor.net/eib/certificates/14627-eib.png 269

Thanks everyone, i really appreciate all the feedback. My picture upload is now complete, unless i've missed something.

Thanks Glen, i've now trimmed the return edges you mentioned and also shortened the elastic between the ab and the kidney which has brought the sides in closer. The Vocoder lines where i have gone over, was a mod that i was advised to undertake in order to make the Vocoder more screen accurate, it took me ages. I'd be reluctant to redo that if its not necessary. I think the lenses must be the pictures, there is no more than 1mm gap around them, even less at the front. Here are some pics of my return edges and sides, hope they look better? Hopefully you can see also i've glued the drop boxes in position as well.

Jamie Kingston UKG / 501st - TK14627 - ANH Stunt TK Casperiser UKG Armourer - CableGuy (Daniel Branton) RWA Armour (2mm ABS Capped), helmet, belt, neck seal, holster RS Propmaster supplied - boots, blaster, gloves 5' 10" height 12 stone weight Voice comms - TRamp PICTURE UPLOAD COMPLETE FRONT BACK LEFT + ARMS RAISED RIGHT + ARMS RAISED AB / KIDNEY ATTACHMENT BUTTON ORIENTATION BUTT / KIDNEY HAND PLATES SHOULDER BRIDGE BACK / FRONT BACK / CHEST CONNECTION THIGH PACK ATTACHMENT KNEE PLATE KIDNEY PLATE / HANS SNAP DROP BOX BACK COD AND BUTT PLATE ATTACHMENT INTERIOR STRAPPING WRIST SIDE OF FOREARMS HELMET FRONT HELMET LHS / RHS HELMET BACK HOVI TIP LENSE COLOUR S-TRIM BLASTER NECK SEAL THERMAL DETONATOR HOLSTER ATTACHMENT

and finally i think i've tidied up my tube stripes, how do these look chaps?

Hi guys, just done some further mods as requested prior to Centurian application, how do these look? Ive also now done the belt, ie tightened it up with additional velcro and glued the drop boxes in the correct position. So i think apart from dressing issues, its now just the helmet to have a go at. Jamie

is this the Han Snap?

ok thank you Joseph, sorry to be a pain but wanted to understand how this works. i'm hoping to try for Centurian once i get through EIB, fingers crossed. Sorry for the slight delay, based on the feedback i had i'm currently re-attaching my sniper knee which will take a few days to cure properly so toward the end of this coming week i'll re-kit up and take some new pictures. i'll post them on my request EIB status thread on the EIB status request forum and drop you a note once i've done that. thanks for coming back to me so quickly.

question guys, i have 2 threads currently active, this one in "EIB Requirements" where i'm having people post helpful feedback on my armour in terms of mods required and also additional pics required (thanks guys so far) and one in "request EIB status" where i have posted my pics but nothing has happened, so..... Q - when i finally have all of my pictures ready, i'm assuming i post them all to my "requesting EIB status" thread and just wait until someone takes a look and either authorises EIB status, or suggests further mods, would that be correct or is there another process i should be following? or .... like the UKG does this current thread form my WIP then it gets reviewed along with my status request? not sure how all this works, sorry. Could someone let me know how this works please guys? Thank you.

will do, thank you. i'll fully kit up again next week once i have glued my sniper knee.

I've now removed the sniper knee and temporarily clamped it into what i think is the right position however the gap underneath is now much larger. Is this how it should be please?

Are these not in line? Could it just have been the angle of the pics? Oh i think i see what you mean, the protruding bit behind the knee plate?

Hi Joseph, hows this for the ab plate?

Jamie Kingston UKG / 501st - TK14627 - ANH Stunt TK Casperiser UKG Armourer - CableGuy (Daniel Branton) RWA Armour (2mm ABS Capped), helmet, belt, neck seal RS Propmaster supplied boots, blaster 5' 10" height 12 stone weight

Hi guys, thanks so far. I've now applied for 501st access so that should be underway. I've not fiddled with the smaller ab plate if i don't need to, i'm worried about removing it and damaging either it, or the surrounding ABS - is that mod essential foe EIB or Centurian? I've straightened up the TD clips, pics attached: I've evened out the trap and tipped the hove miss, pics below: Here attached are some more pics of the ammo knee and the sniper knee:

Requesting 501st access TK14627 www.501st.com/members/displaymember.php?userID=30233 thank you