Tanz

Yeah it was hard to stop as I really wanted that kit to work. Yet, as we now have more images of them and a Hott Toys figure, it is good I waited due to better accuracy for this new kit...well I hope I'm really looking forward to this kit from WTF... it's one that I totally want to rock at Celebration. It all just depends on when the kits are sent out. I picked up a helmet from Skygunbro-Customs but still printing one out.

Yeah it was a bummer but all good. The upper torso needed the most adjustment that simply became hard to do with a 3d print vs. the flexibility we see from some abs kits. He was cool enough to make some adjustment to parts he could, but after a bit its not the best to ask the creator for continuous adjustments to their work. Seeing what we saw in the Maul show on them, there would probably more needed.

Hey there. This ended up going no where as the files were hard to work with due to needed modifications. Even more so now that we have seen more of them in the Maul show. Also now with WTF offering an ABS kit, I placed an order, though for helmet I'm going with the file from FolkyPatrol via Esty as it seems more accurate. Now it really just waiting for WTF on the kit.

So did they just add the Enoch CRL?

The Enoch helmet shown at their booth. https://www.facebook.com/share/19QzuxXH67/

Yeah that was pretty lame. As I walked around I was hoping to see displays.

Yeah they could have cut it out better 😄. I do hope its here for Celebration to get a closer look at, but also for a costume display for Ahsoka where they have his armor up.

So Denuo Novo is offering pre-orders for the Enoch helmet at $700. I'm guessing they will be showing it at their both if they are here at Celebration. Will totally take pics. https://www.denuonovo.com/products/star-wars-ahsoka-captain-enoch-helmet-accessory-pre-order

I was wondering about that...Thanks 🫡

Hi, am totally jumping in on a Enoch build and reading over this thread has been informative. I plan printing up McFlyPrint's armor and after mentioning to him that his thigh armor needed a tweet due to an edge he created, he happily made the adjustments and will be updating his main file if anyone has had an interest in getting his files. Cool thing is that he's open to make any other modifications that will meet the eventual CRL requirements. ✌️

Hey and thanks...I've had to place this build on a hold since now with Season 2 out we've seen more updates on the TK. I've brought attention to changes to the file maker and he's been very cool in making adjustment but still more that needs to be worked on.

Got all the new files and starting back up with the new bucket. The rest will come slowly as I get busier with the holidays coming up Printing the rest of the helmet dealies in resin.

Well, doing a pause on this build as the file maker is updating the files for far better accuracy. The updated helmet looks far more correct as to what's seen in the show So awesome he's doing these updates

The gap is due to me just putting tape between the front and back with no one to help me line them up. The arm opening are big but that's due to that chest not being able to move back in an angle. I'm printing another chest piece right now where I manged to angle the top of the chest back, but will see how it goes. Also the tape really doesn't help keeping it in place on me

So I put the chest together and it seems to look good...but there is what I think a massive gap between it and my chest. If i angle it in more towards me then I open the bottom more and that side connection to the back will angle as well. I could try a heat gun to bend the top section back but that might just mess it all up. I'll toy with Free Form Deformation and see if that helps any. Yet, that can be tricky as well. Let's see what I can do Back later with the update.

Chest pieces printed out today...So will see how this all fits out tomorrow Fingers totally crossed that I measured this right after making that change to the ab section

Thanks...it's getting there. Just reprinted the abdominal section adding 1/2" to it length for a snug but comfy fit. So basically no more donuts for a bit Also reprinting the up left section of the back area, and starting the chest tonight once home from work. This works out then I think the rest would be easier. Yet, not starting the legs until the file maker gets back to me with the new updates.

Totally had to use a bungee chord to check these out. So here's the back and ab sections so far. I have to lengthen the ab section by half an inch to make it a bit more comfortable. Am looking to adjust that underarm section since that curve right now doesn't let me put my arm straight down if I can. The work goes on

Oh man that's pretty cool and totally helpful!

Well, the updated Ab section came out good but I then noticed upon doing a fit test that I didn't lengthen the piece enough, even going off what armorsmith said. I did a reprint and it seems to have worked out this time to properly meet the back section. Had a small heat issue/clog while printing one section but easily fixable once the resin coating/filler/primer are on. Now to print the upper back section. Hope this next print works out

Oh that's rad looking! Makes it way easier to get in those. I'll probably go with magnets or at least see how those work

Yeah...totally bigger looking. Why I do the test strips for the sections...sonif to small or big I can make the adjustments. Hi, and thanks. Yeah this will be an interesting build. I hope to be able to go for approval once done. Yet, build first then focus on that. Luckily the file make is more than happy to help with future adjustments if needed.

Got a newer update for the abdominal section since the original had an issue. Now back in Amorsmith seeing how things fit. Now the only issue I have with the program is that other builder have told me NOT to make a part completely cover a body section with a piece of a kit; saying that it will print far too large. Telling me that I should allow some of the avatar to show through. So back to printing fit strips for the sections and see how this goes. Now to print the Ab section again. That part is always the key to all the other parts. If it comes out great I'll post the updated print

Well, a super big thanks to Gmrhodes13 for providing the file maker with information to help update the armor file for better accuracy. Also to Mcflyprint for being totally down with making any necessary adjustments. His files just getting cooler and cooler. So after going over the new files its time to put two of my four printers are back to work. Did a test print strip on the ab section after tinkering with it on Armorsmith, and all seems good. I guess I'll have to see what the morning brings. https://imgur.com/u0EgOi5gur](https://imgur.com/TkXRQsZ) I totally hope this project comes outs as cool as I'm imaging it

That's cool man, and thanks. Yeah I had seen the difference in the photos and was wondering about the file. The angle of the belt also had me thinking. Cool you reached out to him. I always talk to him through Instagram DM. So I'll send him that pic of the sides. Yet if there's other information and he doesn't get back to you let me know. I had sent him the pic of my test fit and he's offered to make any adjustments to his file since he's wanting to make his pretty spot on.