erv

I have some blaster core V4 for sale at my website. I thought I would revive that topic as some folks were looking forward to get a board.

Hi ! I already posted my initial research on the RPF about those parts, just reposting the link here for convenience http://www.therpf.co...45/#post1434827 nice pick on the capacitors. My knowledge : A) : Tuning coil of the distributed amp. Most people I talked too mentioned a possible IF stage at 9.72 MHz B : Capacitors C) : EF91 or 92 sockets, used until the mid 60's D) : the other coils of the distributed amp (high side it seems) E) : very clearly an antenna / VHF output. Relics of those you still find in your car radio antenna connection my mentor mentioned that for the actual devices that were put in aircraft, it could be more minature (valves of the size of a crayon) but it could be a larger plane. Still, using EF91-92 type valves would rather suggest ground based military equipment. This is not a power stage (electronically speaking) but a signal amplification (wide band) stage, so you cannot base the analysis on the size of the valves only.

I redrew the eagle from the pic of an actual counter with the logo. However, with 96x64 pixels on the screen, I'd rather occupy the whole screen and not just a real sized logo. I mostly did it for the "nostalgia" of the logo since mine didn't have it. Bottom line : those graphics are changeable. I'm happy to install on the screen any better artwork one would send me crappy video I made a long time ago. Skip to 4'47" for the effect. http://www.youtube.com/irvinplecter#p/u/54/Gezd-DLSwu0

aside of my explanation below, the whole blaster isn't really "canon" per say so I didn't really cared about it. My concern was more about having fun adding Blastech R&D back story to the blaster. The text in your diagram is incorrect. The ring mount bracket isn't part of the mounting of the scope itself. No at *all*. The scope is attached on lower mount (crossed hinges, springs etc) with the 2 hex bolts and nothing else just like the other scopes. The ring only clamps the small device on the top of the scope that houses a small mazda light bulb with a red filter as explained in my build log. I didn't want to discard a cool light up feature in the scope on a blaster that was already non canon.

thanks for the kudos folks ! The last thing that doesn't work (yet ?) is a real stun mode for when my little one is ruining our energy (the force is strong with this one). On a side note, not sure when I'll be able to schedule this (time wise and financially speaking) but an armor is planned. I already have the bucket and the voice amp with the static burst. Still, I have many props replica I'd like to build first !

Thanks guys ! Not sure I understood that properly. My scope is mounted "normally" from under, with screws, on a scope rail. The original attachment with hinges and springs was removed. The ring area in the middle just holds the top light that illuminate the scale inside the scope. That ring isn't part of attaching the scope to the blaster or to the rail.

Cut the ring. Won't put it back, it looks cool enough without and I like the brass accent. I was able to disassemble most parts and the PC job went well. Some area look like there are packets but it's just due to the grainy surface of the scope which is now partially covered. The lit internal reticule is FANTASTIC. Used a red SMD led and an old coax cable to grab power inside the henglser counter. my best attempt to show you what you see in the scope. Lit markings and azimuth scale AND targeting lasers. :004: I won't put any other fake reticule on a red filter or anything, it would ruin the fact that scope is REALLY working ! still have to perfect the white lettering (and try the white crayon) but I can call it done !

Finished my galv-etched plate. My first attempt to etch an aluminium plate with the new film. Still need some improvements, photo film transfer had minor dents and permanent marker doesn't resist to the galv-etching process. Will make a better one next time. Signing the plate isn't a sign of being egocentric, but just a convenient way to hide one of the dents scope time first I tried to disassemble the front lens. I don't have the special tools required for that so I gave a shot to that however, it seems that the scope got a shock and the lens mount isn't circular anymore. I got the bolt almost out but I had to screw it back or ruin anything. I got worried the anti glare coating on the lens will go away will the stripper but since acetone never ruined my glasses I gave it a try. I disassembled first a smaller part that didn't have any optic in it an tried my PC stripper. Worked like a charm in seconds. I put a silicone plug in the exposed part of the inside of the scope to avoid the jelly stripper to get in and I immersed the scope. then I noticed a screw that locks the lens ring. however, after trying my mocked up tool, the ring wont come out. I now have to hope it will accept the 200°C of the PC cure. A simple kitchen glass withstands it so I'm not really worried. As for the A2 model, it has, like I said, a little light bulb attachment on the top. I put a white led there to test : it lights up the azimuth scale engraved on the glass inside. I left enough space between the ring and the lens to eventually insert a red filter to make a canon reticule. I really dig a scope that lights up inside ! I'll grab some power supply from the hengsler counter to drive the top led.

... A mini screen... The side of the counter has some dirty edges. That's due to the PC job I ****ed up with the Eastwood powder. Not having the right stripper made my like VERY difficult on that one. I thought I had removed everything but no (of course). Not "ugly" but could be better. Too late :ohwell Boot sequence featuring a imperial logo being filled up. I shortened the boot sound of 20%-ish to get it perfectly synched with the boot animation. Custom title of that one, the "E-11-X" Front side of the counter. I kept the optic it makes the 3mm leds occupying the whole space and they look a bit oval, I like it. The reset button of the counter is now the menu switch to browse thru the different screen of blaster core. Radar screen and ammo counter Screen saver. It's blurrier than a normal screen due to the export of the video, but it looks better in person I added 3 new "menus" to the firmware. My counter wasn't the "right one" with the Eagle Logo, reason why I had no remorse cutting a window for the screen. However, I felt nostalgic about it so I mocked up a digital version. Another screen with a static imperial logo (always efficient and iconographic) Last screen, a system info displaying the charge and voltage of the battery (the config file has 2 PLI settings for that purpose). I also had fun with some extra verbiage on that one. The cell/battery icon on the left isn't depleted in real time to avoid flickering on the sprite but it's updated each time you pass in the menu. The voltage and the charge % is updated in real time though, and you see it fluctuating a bit when you fire. I did my best for the details. Wires (ribbon cable) going to the counter are hiden in a black mesh tubbing. Quite organic, my favorite. I also put some of the anti mosquito mesh to hide a bit the second speaker that is in there. Same on the front of the counter. I also put a screw head and a small crystal to hide the hole left by the removal of the reset mechanism of the counter. The wires coming out from the counter will be really used. I've always thought that the magazine cylinders should be some kind of smart targeting system (obviously not "finished" since the blasters end beaten by the sabers). Since it's the E-11-X I could invent anything after all. I'm therefore installing 2 red lasers in the mag cylinders. They are controlled by the rear sight mechanism. I got that idea from the very beginning and that's why I wanted to make THIS very model of blaster : wire from counter to mag cylinders and scope rail stopping BEFORE the sight. Like here To avoid any switch between the outside of the main body and the internal electronics, I used (again) a hall effect sensor, installed in the PVC chassis. 2 magnets inline are installed in the scope reticule that activates the lasers in the "accurate aiming" position of the sight. The stand. I got the smoked plates for free. I discovered later that it's polycarbonate, 1 cm thick, I got many panels it's worth a fortune. Attached 2 pieces together and made the stand with it. PCed legs with accent rings (quick cut with the lathe). I still have to make a galv-etched plate now that I have the resist photo film and finally, video time. Sorry for the length, I really think I had to detail that one. E-11 model X Custom Blaster - 3 videos

For the crystal, it's made out of real quartz (aqua aura), I thought it could be the collimating element for the plasma, crystals evocate optical / light stuff. At the end it's kind of coherent with the wookiepedia article Blaster - Wookieepedia, the Star Wars Wiki Testing the trigger group before final install in the handle. You can spot the aux. switch in the axis of the locking screw that is going to be parted in 2 halves. the half that will go on the back of the aux. switch (I installed a small M3 screw there) installed and it screws fine to the "lock" position as read on the handle The other half of the screw, mounted & screwed on the switch cap/plunger. I used some anti mosquito mesh / lattice that I powder coated with black chrome II. Then I glued some black fabric tape with a glue spray to hide the electronics. I looks a bit like a carbon mesh (not exactly, just the "style"). I like it very much. Worked on the T-track I got from Gino. Bent with a lighter, smoothed with gentle heat and finger, then sanded at the ends. Painted flat black with automotive paint, glued with a few spots of epoxy, except the top one since it blocks the scope rail from being removed and I still need to install the scope (it's mounted with magnets so that it's easily removable) Folding stock installed. Replaced the nails by 2 stainless steel M2 screws. Not sure I'll paint them black, I like the steel accents. Reworking the firmware. I had ideas that were not ready for that release, but I wanted to prototype some of them for my E11. Hence, I made sure I had a flashing connector accessible from the rear of the blaster. Milled a slot in the henglser counter. Why ? because there's something else requiring potentially some upgrade too.

Mag cylinders ! Thumbs up for Russrep accurate pictures he posted in his thread (RPF), I did my best to get a scale out of them, but credits go to his work. aligning the lasers took a while, even now it's not perfect but since the magazine catch isn't laying flat on the weapon itself, the targeting sensor laser beams are never aligned. I like it too, it's just point at 2 different location of the target. Now we know pretty much the parts (but not the source device - read here my recent "research" as Private Erv' http://www.therpf.com/f9/sterling-mag-cylinder-mystery-20345/) but still, I couldn't find any suitable replicas of the central capacitors in my drawers. The original ones are rated for 70° and won't have withstood PC curing at 400°F so no regrets, I machined cylinders that look like them pretty close. I happened to play with the PBTP satin and *when cured at the right temp* it's definitely more gloss than the eastwood PC. Flow is just perfect. However it wasn't matching the gloss of the rest of the blaster so I used a coat of an automotive paint that has very little gloss (same as on the T-Track). I left the front cap and nut natural, I like contrasting metal and it really marks the "special X model" of the blaster

Getting close. Received my uber accurate T-tracks from Gino yesterday. Strong ABS extruded plastic with the right gaussian profile. Grinding the bolt. Why ? because it's hiding something (see below). Taking a picture while actually grinding isn't easy when you have only 2 hands and no tripod and when you're tired to make efforts... (I know, use the Force to levitate the camera) wiring the satellite board on the barrel. After checking between having it right next to the Blaster Core board or here, it was easier like that, less wires and an easy power supply split for the barrel end flash RGB led. The latter has its power xtender and resistors all local, and protected with heatshrink. Once glued, the LEDs were covered with some masking liquid (latex from what I smell... brand is Maskol by Humbrol), then I painted the whole barrel with some regular satin paint. It's weird to work again with spray paint once you've done some powder coating. Takes ages to dry (impatient me), chips and marks easily buy since it's going INSIDE the body of the E11 so I don't mind. A big part. A crystal chamber. I wanted to have (among other things) some glams for that projects. Also, the bolt is visually such a nice piece of mechanics that I refused to do a static thing with it, with a piece of chrome tape. So you can still weenie the bolt and it moves back to reveal some (simple) internals. I mounted an aqua aura crystal on a small ring/mount JBwelded to the bolt and it goes straight in the barrel. The internals were assembled on a thin copper plate (polished a bit), the thin comb of brass/gold is an old SD card reader that came with my previous laptop, as well as the control card (sanded, and glued). You can also spot 2 anakin brass pins, a weirdly shaped coil from a hard drive and a few other bits I had in my drawers. Once everything was installed, I placed a small headless screw behind the handle to stop the bolt from going back too far (and smashing the wires going in the handle, to the trigger group). It's not moving back a lot, but it's enough to reveal the internals. No led there and no reason you'll have any, getting the bolt back disables the weapon. Initially, I was supposed to use the bolt as a range selector / unjamming operation but I didn't have the right spot to place the sensor/switch and I consider the bolt and wires just behind it too fragile for using that on a standard base. Installing the electronics in the back. It's one of the most difficult wiring job I ever had to do (my yoda saber retrofit was easy in comparison). Not only there are a LOT of wires but they have to extend to allow servicing the board if need and they have to fold properly when the chassis (PVC) is inserted in the body of the sterling. Add then that you have the functional spring and the bolt that still have to move freely without smashing the wires. Also, fourteen (14 !) wires are going to the henglser counter. Holy cow. I used some of my 30 AWG ribbon cable. It's a solid wire in there (no strand) but that was my only choice. The trigger group. No limit switches, but Hall effect sensors and small neodymium magnets (3mm OD) and secured with activated (spray) cyanoacrylate glue. They act as a switch when the magnet is close enough. Inside, it's actually an open drain MOSFET transistor, just like a power xtender board. The only switch I used is for the AUX switch (range / reload). I'm going to cut the screw that secure the trigger group to the handle and body and the rounded end (the one not having the screw driver slot) will be attached to the switch plunger (removable). On the other side of the handle, where you read the "Free / Lock", the other half of the screw will go on a M3 head less screw that installed on a small bolt then glued on the back of the aux switch with some JBweld. Original Look will be preserved. more to come, I've taken about 110 pics during that build log :duh

The choice of alu for the main tube/receiver is due to my location. You just can't imagine how it's hard (or extremely expensive) to buy metal in here, plus with the metric system, the closest size were either 35 or 40 mm. Then I don't have TIG welding equipment, so I did it this way. I've seen another project where the member brazed the parts together, I was very impressed on how good looking the sterling ended. the kit I got was chopped this way Even getting alu tubes in the UK shipped to me wasn't that easy, since it's heavy and not all vendors will accept to ship across the channel :unsure Also, with the humble machining tools I have, alu remained the easiest solution. here's some more of the build log. I wanted to have the blaster Powder Coated cause I like props you can hang around with, without the fear of paint chipping and so forth. 2 stressful days cause I was SO afraid to miss the PC job. I first went to buy some oxalic acid (you guys call that Naval Jelly, rust dissolver) to prep things nicely. I also baked the folding stock and the main body since I noticed it helped neutralizing the rest of paints, oil and so forth. Baking also gave the final kick to the steel epoxy on the main body, which stabilized and didn't melt at all. Then I cleaned with water, then with biodegradable degreaser, and wiped properly, then compressed air to blow away any trace of moisture. I resisted to the envy to re coat the folding stock (an area isn't thick enough) but I didn't. Too risky. First, I remembered about the faraday effect during the PC job, and I was worried about not having the inside of the barrel dark enough. So I protected the beast and PCed the inside with a light mist of flat black (then I hadn't made more experiments with the satin black I had and I didn't want to ruin anything). then after experimenting the right flow out time and temp on a scrap part, I played again with the satin black on the trigger and its guard. I learned there how to (almost) fully disassemble a trigger group, which helped for cleaning it from all the grease. PCing the folding stock. First stress of the day final results once I've baked all the parts (the oven heated the whole afternoon, I couldn't stop). I also made my scope rail. Still a light texture but that's exactly what I wanted You can see the difference in the texture of the butt cap. It's not just due to the primer coat of flat black, the surface of the metal was different. Stock locks (and 2 smoking barrels :lol) the shorten magazine with a nice decorative inserts (SO-dim 1GB... well that's only 512 MB now :rolleyes - They didn't want it back at work after I upgraded on my previous machine)

Shaving various parts. Tedious. Don't know what God modeled after him but he had some smart enlightenment when he got B&D inventing the electric file. Let there be steel powder. This is the front flash deflector Measuring the eject port. Since my templates were shrunk of 10%, I rubbed some grunge on a piece of paper to "measure" the original one. Yes, I also used a digital caliper too :unsure Extracting the stock mount. Fortunately the pins are coming out easily. Easier than removing those **** on a MR saber :hate Shaving time again. Sorry no Gilette cream. Sorry about the heat. But admit it you look much nicer now. fitting like husband and wife (which is never perfect as you know) Rear sight. I'm cheating on that one, I'll leave a superficial layer of the original body tube to have a large flat surface for the JB weld to stick on (+ a headless screw or 2, or simply JBweld rivets). No one will notice a 2/10th mm difference in the part height. The handle and trigger group holder. Same as above. Some is cut out but I leave some surface for the attachment. No point of having that section fragile. Cleaning the muzzle. I got a HARD time extracting it. Then I machined it. Fits the barrel like a charm (supposed to). What I have to re install The butt will be coupled to the main body by just machining both parts (reducing a little bit the body OD on a 1" sleeve, and increasing a bit the ID of the rear ring, then JBweld)invisible. Electronics will remain accessible from the rear. I've identified how I'll handle the blast and the semi/full auto mode, using the the REAL SELECTOR and trigger. Very easy. More detail on that later. I also have some glams idea.

Hi ! I thought I'd share that work here too even if already posted on the RPF and other forums, just in case you guys want to discuss or ask questions. Background : I wanted to make a E-11 for a long time, my customer Pablo and his scratch built did put the scale UP. I considered screen accurate for a while, but I decided later to go for a custom E-11 since I wanted to add a screen to the blaster, hence non canon (I hope I'm not hurting any feelings). Rather than scratch built (very tempted to follow that path though), I chose real sterling parts. Here is the build log with many pics, I though that might interest some of you. SHORT CUT : here's the video :-) E-11 model X Custom Blaster - 3 videos The sterling came in chopped pieces which is the short "cut" (:happy) to disable it. Sure, it won't *ever* work again this way... The first part of the exercise is to extract all the bits and parts then clean/Shave them and re install them on the main body that will be scratch built. The rest I hope to have as many vintage parts as possible on that blaster. The scope is missing but it is on my way as I'm typing this. cutting the read sight and the removable butt cap Building the main body. The PVC BBC templates are for a 42mm OD tube matching some plumbing supplies. The real sterling is made out of a 1"1/2 OD tube. I managed to find the right diameter and correct wall too, on ebay.co.uk, tubes being sold as coolant pipes. Made of sturdy 6063 T6 aluminium from what I remember. The downsizing of the templates are an exact 10%. I shrunk only the width to match the perimeter, holes are oval but since I know what the size is supposed to be (7/16" and a few of 1/2"), so I just needed the alignment and spacing, aside the front stock lock groove that was measured on the original part and cut accordingly. I'm so happy I have those stepped drill bits. (In inches :thumbsup) Many centers and drills later... Cutting the long groove Done. Jump for joy. Cool yourself down. And wash your dirty hands you dirty boy. Some sanding to clean the outside. I used a file to clean the sharp metal edges inside, then cleaned the wall of each hole with a sharp knife, then finally put some sand paper on a piece of blade to get a nice finish inside. Then, some threaded rod and a piece of aluminium matching the ID, with sand paper taped on it => drilling machine => clean shave of the inside of the tube. I was impressed to see that the bolt is perfectly fitting in that tube ! I don't want to have a huge post with everything inside, I'll keep posting the rest of the various stages of the built later !

[entering informative but non advertising mode] Hi there, just a quick note to let you know my blaster core and voice core are on my website, very limited stock. I'll build more once I'll be installed in my new house. For the voice core, the final video has been uploaded on youtube, in case some of you are interested. Please don't answer here about Voice Core, if necessary, create a new topic and notify me, I'll be glad to be some input there. Otherwise, use the website and the contact form for questions. The user's manual of those 2 boards are online in the documentation section (Manuals are written in english) http://www.youtube.com/irvinplecter" target="_blank">http://www.youtube.com/irvinplecter [/EOT] *static burst* Erv'

si !!! a la piazza navona !!! (isn't it the place where boyz n' gals meet and flirt, in Rome ? don't know if they accept blasters... sorry to derail this one)

Hi folks, so just a little additionnal comment, I don't mean to do *any* advertising about my electronic boards but I've already been into some email answering in the past 2 days, strangely, people started asking me about blaster core to sum it up : - it should have been released in december or so. Too busy with crystal focus (for sabers), no time to write the user's manual, I've released it only to specific people I met online with whom I shared about blasters and established that they would be able to handle the board without a too detail manual (as a start at least) - manual is there now - I still have some parts and PCBs to make a few (less than 5, and only one graphic display left) - I won't order more parts before the end of june, I'm moving and I'm waiting for some parts to be available for crystal focus before I can make a big groupped order for all my boards supplies. - if you are interested, create an account at plecterlabs and subscribe to the newsletter, I might start a preorder list for blaster core during the summer, after I move. - I'll come back to you soon for the Voice Core, already demonstated in my youtube videos http://fr.youtube.com/watch?v=T2W2n1o0Ebw" target="_blank">http://fr.youtube.com/watch?v=T2W2n1o0Ebw and http://fr.youtube.com/watch?v=2BlkpypjIsM" target="_blank">http://fr.youtube.com/watch?v=2BlkpypjIsM I'll have like 15 or 16 voice core to throw in the wild very soon. First I'm waiting for some beta testers, and I still have to write the user's manual. If you are interested by either one or the other board, please email me thru the website, I don't want to derail or polluate this topic, neither to do "advertising". If someone thinks that Voice core or Blaster core are worth making a topic in this forum (I'm totally novice here and I'm not part of the 501, rebel scum I am), please start one but after talking to a moderator cause I don't want to be considered as an agressive vaccum cleaner sales man coming to your door step Erv'

I'm really proud my blaster core board ended in this kind of beautiful blaster ! Congrats Pablo ! Erv'