Ladon[TK] Posted December 2, 2025 Report Posted December 2, 2025 This is my ANH Stunt TK from Authentic Props. https://imgur.com/a/URfExfA Quote
gmrhodes13[Staff] Posted December 2, 2025 Report Posted December 2, 2025 Hi Shane when posting images we usually try to add them all (showing) to your post, a great how to here Overall looking good, there area few things for basic, and a few adjustments will be needed for higher level 2 and 3 (EIB and Centurion) Belt should come up at the back. Detonator end caps, gaps and panel incorrectly sized Top of rear calves cover strip should stop under the top ridge You can also remove the sharp corners on the rear of the forearms, if you wish. Also nip the corners (cut or round off) so they don't catch when moving Tighter strapping between the back plate and kidney may reduce the gap shown. For higher levels Shoulders could come inwards at the front to reduce the gap Belt could come up a touch The top of the ABS belt shall sit at or just above the bottom of the central and vertical ab button panels. A slight overlap is suggested, but not required. You could cut the extra material from the ends of your forearms under the biceps, they can catch when moving. You could also bring the down a touch just to give you a bit more room. Thighs could come up a touch, will give you some room at the knees. Also adding some stiff foam behind the sniper plate can push forward to stop catching on the thigh. Also noticed the left leg thigh is on an angle, as I have very thin legs I added some foam to the insides of the thighs to keep them central. Also match gaps between forearms and gloves/handplates Drop boxes should stop at the end of the plastic belt For Level 3, the corners of the plastic ammo belt shall be trimmed at a 45 degree angle that meets the outer edge of the cloth belt. For a more screen accurate look, it is suggested that the top of the rear ridge of the sniper plate be aligned with the top ridge of the calf. Also note that the sides are angled rather than curved. Shoulder straps on the rear should sit on the backplate, elastic loops can help this but you may also need a hot water bath You could add some scrap material behind the gaps in the lower ridges, also fill the seam with ABS paste or miliput or silicon (or something similar). Looks like your inner thigh ammo strip is attached incorrectly, it should be mounted to the lower ridge just like the outside Front views Back views You may need tighter strapping on the sides to reduce the gap, doubled over elastic can help. Han snap should not be painted should be silver Also for L3 you would need silicon handplates Hand guards shall be latex or latex-like, solid white or painted white, and affixed to rubber gloves with no visible strapping or stitching. A few other things on the helmet Vocoder should be sharper Hovi tips rim painted, also white inside Tube stripes should be the same gap from the cheek, yours angles downwards towards the back A little hard to make out some other helmet details. So a few adjustments for basic and I would highly encourage you to also seek the higher levels approval once you've been cleared for basic. Good luck 1 Quote
Ladon[TK] Posted December 2, 2025 Author Report Posted December 2, 2025 15 minutes ago, gmrhodes13 said: Hi Shane when posting images we usually try to add them all (showing) to your post, a great how to here Overall looking good, there area few things for basic, and a few adjustments will be needed for higher level 2 and 3 (EIB and Centurion) Belt should come up at the back. Detonator end caps, gaps and panel incorrectly sized Top of rear calves cover strip should stop under the top ridge You can also remove the sharp corners on the rear of the forearms, if you wish. Also nip the corners (cut or round off) so they don't catch when moving Tighter strapping between the back plate and kidney may reduce the gap shown. For higher levels Shoulders could come inwards at the front to reduce the gap Belt could come up a touch The top of the ABS belt shall sit at or just above the bottom of the central and vertical ab button panels. A slight overlap is suggested, but not required. You could cut the extra material from the ends of your forearms under the biceps, they can catch when moving. You could also bring the down a touch just to give you a bit more room. Thighs could come up a touch, will give you some room at the knees. Also adding some stiff foam behind the sniper plate can push forward to stop catching on the thigh. Also noticed the left leg thigh is on an angle, as I have very thin legs I added some foam to the insides of the thighs to keep them central. Also match gaps between forearms and gloves/handplates Drop boxes should stop at the end of the plastic belt For Level 3, the corners of the plastic ammo belt shall be trimmed at a 45 degree angle that meets the outer edge of the cloth belt. For a more screen accurate look, it is suggested that the top of the rear ridge of the sniper plate be aligned with the top ridge of the calf. Also note that the sides are angled rather than curved. Shoulder straps on the rear should sit on the backplate, elastic loops can help this but you may also need a hot water bath You could add some scrap material behind the gaps in the lower ridges, also fill the seam with ABS paste or miliput or silicon (or something similar). Looks like your inner thigh ammo strip is attached incorrectly, it should be mounted to the lower ridge just like the outside Front views Back views You may need tighter strapping on the sides to reduce the gap, doubled over elastic can help. Han snap should not be painted should be silver Also for L3 you would need silicon handplates Hand guards shall be latex or latex-like, solid white or painted white, and affixed to rubber gloves with no visible strapping or stitching. A few other things on the helmet Vocoder should be sharper Hovi tips rim painted, also white inside Tube stripes should be the same gap from the cheek, yours angles downwards towards the back A little hard to make out some other helmet details. So a few adjustments for basic and I would highly encourage you to also seek the higher levels approval once you've been cleared for basic. Good luck Awesome! Thanks! I'll start working on it right away. 1 Quote
gmrhodes13[Staff] Posted December 2, 2025 Report Posted December 2, 2025 2 minutes ago, Ladon said: Awesome! Thanks! I'll start working on it right away. If your tube stripes are stickers you should be able to apply some tape on top, then gently lift the corners and lift the tape slowly, they should all come loose with some care, then just reapply in the correct position and remove tape. References on placement here Quote
Ladon[TK] Posted December 2, 2025 Author Report Posted December 2, 2025 1 minute ago, gmrhodes13 said: If your tube stripes are stickers you should be able to apply some tape on top, then gently lift the corners and lift the tape slowly, they should all come loose with some care, then just reapply in the correct position and remove tape. References on placement here They are the only stickers. I had painted everything else. 1 Quote
Ladon[TK] Posted December 2, 2025 Author Report Posted December 2, 2025 Can I remove any material on the calves and Thighs? I walk like a toddler. My thighs are large and shaped oddly. I have the thigh armor up as high as I can take it before it bites into my groin. Quote
gmrhodes13[Staff] Posted December 2, 2025 Report Posted December 2, 2025 5 hours ago, Ladon said: Can I remove any material on the calves and Thighs? I walk like a toddler. My thighs are large and shaped oddly. I have the thigh armor up as high as I can take it before it bites into my groin. Personally I would try to lift up your thighs to give you some more room, you do have a lot of black showing. But yes you can, they are called mobility cut outs, a lot of the costumes had them, gallery here Please note from the CRL: THIGHS Any mobility cuts on the back do not extend beyond the top of the raised ridge. SHINS Any mobility cuts on back of piece do not go past raised ridges. Quote
Ladon[TK] Posted December 2, 2025 Author Report Posted December 2, 2025 (edited) https://imgur.com/a/URfExfA#rlibfLu EDIT: Ignore this post. I'm testing to learn how to post images properly. Edited December 2, 2025 by Ladon 1 Quote
gmrhodes13[Staff] Posted December 2, 2025 Report Posted December 2, 2025 4 hours ago, Ladon said: https://imgur.com/a/URfExfA#rlibfLu EDIT: Ignore this post. I'm testing to learn how to post images properly. You need to use the link with the file extension, example .jpg .png .bmp .gif Either the Direct Link or right click copy and paste Apparently it can be a pain in mobile app 1 Quote
Ladon[TK] Posted December 3, 2025 Author Report Posted December 3, 2025 Okay, here we go. Made adjustments. https://imgur.com/gallery/501-pre-approval-2-0-7EshqKD#cJeSy4O https://imgur.com/gallery/501-pre-approval-2-0-7EshqKD#BvtRdYE https://imgur.com/gallery/501-pre-approval-2-0-7EshqKD#rfuD0Rr https://imgur.com/gallery/501-pre-approval-2-0-7EshqKD#SzolMj1 https://imgur.com/gallery/501-pre-approval-2-0-7EshqKD#p39BHYy https://imgur.com/gallery/501-pre-approval-2-0-7EshqKD#PmkKwL4 Thanks again! Quote
Ladon[TK] Posted December 3, 2025 Author Report Posted December 3, 2025 https://imgur.com/cJeSy4O https://imgur.com/BvtRdYE https://imgur.com/rfuD0Rr https://imgur.com/SzolMj1 https://imgur.com/p39BHYy https://imgur.com/PmkKwL4 Quote
Ladon[TK] Posted December 3, 2025 Author Report Posted December 3, 2025 Just now, Ladon said: https://imgur.com/cJeSy4O https://imgur.com/BvtRdYE https://imgur.com/rfuD0Rr https://imgur.com/SzolMj1 https://imgur.com/p39BHYy https://imgur.com/PmkKwL4 Quote
Ladon[TK] Posted December 15, 2025 Author Report Posted December 15, 2025 Its official! TK12325 Reporting in! 1 Quote
gmrhodes13[Staff] Posted December 15, 2025 Report Posted December 15, 2025 Congratulations trooper and welcome to the ranks A great read for the newly approved trooper, Legion Trooper Survival Guide https://drive.google.com/file/d/1tHqwvdZ2k5pxcxxHVWZxXOSxah4DnHR8/view?usp=sharing Once you start trooping post a trooping record, you can gain awards at specific levels, more info You can also request Letters of Commendation Good luck and hope to see you trooping soon 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.